79.060.01 木基板材综合 标准查询与下载

GSO ISO 16987:2009 人造板 在定期测试条件下测定防潮性

This International Standard specifies a test method for the determination of the moisture resistance of woodbased panels under cyclic test conditions.

Wood-based panels – Determination of moisture resistance under cyclic test conditions

GSO ISO 9426:2009 人造板 板材尺寸的指定

This International Standard specifies methods for measuring the thickness, width and length, as well as the squareness, edge straightness and flatness of wood-based panels. It applies to full-size flat panels.

Wood-based panels – Determination of dimensions of panels

GSO ISO 16999:2009 人造板 取样和切割部件进行测试

This International Standard specifies certain rules for the sampling and cutting of test pieces. It does not cover the sampling and cutting of test pieces for the derivation of characteristic values for structural design. These tests are carried out on medium-sized test pieces.

Wood-based panels - Sampling and cutting of test pieces

GSO ISO 16979:2009 人造板 含水率的表示

This International Standard specifies a method for determining the moisture content of wood-based panels

Wood-based panels - Determination of moisture content

GSO ISO 16978:2009 人造板弯曲弹性模量和弯曲强度模量的测定

This International Standard specifies a method for determining the apparent modulus of elasticity and bending strength of wood-based panels in flatwise bending.

Wood-based panels- Determination of modulus of elasticity in bending and of bending strength

ANSI/NECA 407-2009 仪表板的安装和维护用标准

This standard describes installation and maintenance procedures for panelboards, and special procedures used after adverse operating conditions such as a short-circuit, ground-fault, or immersion in water.

Standard for Installing and Maintaining Panelboards

EN 1058:2009 木基板材.特征5-百分位数值和特征均值的测定

On the basis of test results from wood-based panel products for structural purposes,This European Standard specifies a method for the determination of: characteristic 5-percentile values of mechanical properties under the assumption of a log-normal distribution of the test data according to EN 14358; and characteristic mean values (50-percentile values) of physical properties under the assumption of a normal distribution of the test data. Test data should be determined from tests using the test methods outlined in EN 789.

Wood-based panels - Determination of characteristic 5-percentile values and characteristic mean values

KS F ISO 9424-2008 该木质片状试样的尺寸测量方法

Wood-based panels－Determination of dimensions of test pieces

KS F ISO 9426-2008 木质板材板材尺寸的测定

Wood-based panels－Determination of dimensions of panels

ISO 12460-4:2008 木基板材.甲醛释放的测定.第4部分:干燥剂法

This part of ISO 12460 specifies a desiccator method for the determination of the quantity of formaldehyde emitted from particleboard, fibreboard, plywood, oriented strand board (OSB), and wooden laminated flooring.

Wood-based panels - Determination of formaldehyde release - Part 4: Desiccator method

ISO 12460-3:2008 木基板材.甲醛释放的测定.第3部分:气体分析法

This part of ISO 12460 specifies a procedure for determination of accelerated formaldehyde release from wood-based panels using the gas analysis method.

Wood-based panels - Determination of formaldehyde release - Part 3: Gas analysis method

SNI ISO 16979:2008 木制人造板. 水分含量测定

Wood-based panels - Determination of moisture content

BS DD CEN/TS 12872:2007 木基板材.楼板、墙壁和屋顶中承重板的使用指南

This document gives guidance on the use of wood-based panels in structural applications as structural floor and roof decking on joists or structural wall sheathing on studs in accordance with EN 12871. It provides information on: ? inspection at site; ? transport and delivery; ? handling; ? stacking; ? storage; ? moisture content, conditioning and the effects of moisture; ? cutting and machining; ? selection; ? installation.

Wood-based panels - Guidance on the use of load-bearing boards in floors, walls and roofs

DIN CEN/TS 12872:2007 木基板材.楼板、墙壁和屋顶中承重板的使用指南

Wood-based panels - Guidance on the use of load-bearing boards in floors, walls and roofs; German version CEN/TS 12872:2007

GSO ISO 20585:2007 人造板 浸入70°C或100°C（沸腾温度）水中后湿抗弯性的测定

This International Standard specifies methods for determining the bending strength of particleboards and fibreboards after immersion in hot water. Method A is applicable for water at 70 °C and Method B for water at 100 °C (boiling temperature). NOTE The boiling temperature can slightly differ depending on the altitude above sea level.

Wood-based panels - Determination of wet bending strength after immersion in water at 70 degrees C or 100 degrees C (boiling temperature)

GSO ISO 16983:2007 人造板 浸水后厚度膨胀的测定

This International Standard specifies a method for determining the swelling in thickness of flat-pressed or drum-pressed particleboards, fibreboards, OSB, and cement-bonded particleboards, after immersion in water.

Wood-based panels -- Determination of swelling in thickness after immersion in water

GSO ISO 16985:2007 人造板 测定与相对湿度变化相关的尺寸变化

This International Standard specifies a method for the determination of dimensional changes in wood-based panels, due to variations in relative humidity.

Wood-based panels - Determination of dimensional changes associated with changes in relative humidity

GSO ISO 16984:2007 人造板 垂直于板面拉伸强度的测定

This International Standard specifies a method for determining the swelling in thickness of flat-pressed or drum-pressed particleboards, fibreboards, OSB, and cement-bonded particleboards, after immersion in water.

Wood-based panels - Determination of tensile strength perpendicular to the plane of the panel

LY/T 1717-2007 人造板抽样检验指导通则

本标准规定了人造板抽样检验的术语、定义、符号和缩略语、人造板产品外形尺寸和外观质量的计数抽样检验、人造板物理力学性能检验结果的表示和判定、生产企业产品质量控制的计量抽样检验、两检验室测量结果一致性的统计检验和检验报告。 本标准适用于人造板实施型式评价、例行生产、监督、交收、质量一致性等多类检验的抽样系统、抽样计划、抽样方案和检验数据统计处理。 本标准不适用于结构用人造板的抽样系统、抽样计划和抽样方案等。

Guide for sampling inspection of wood-based panels

ISO 12460-1:2007 木基板材.甲醛释放的测定.第1部分:用1立方米试验室法测定甲醛排放

This part of ISO 12460 specifies a 1 m3 chamber method for the determination of the formaldehyde emission from wood-based panels under defined conditions, relating to typical conditions in real-life.

Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the 1-cubic-metre chamber method