79.060.01 木基板材综合 标准查询与下载

DIN EN 325:2012 木质板料.试样尺寸测定

Wood-based panels - Determination of dimenions of test pieces; German version EN 325:2012

BS EN 325:2012 木基板.试件尺寸规格的测定

Wood-based panels. Determination of dimensions of test pieces

DS/EN 325:2012 人造板试件尺寸的测定

The standard specifies methods for measuring the thickness, length and width of test pieces of wood-based panels.

Wood-based panels - Determination of dimensions of test pieces

EN 325:2012 木质板料.试样尺寸测定

This European Standard specifies a method for measuring the thickness, length and width of test pieces of wood-based panels.

Wood-based panels - Determination of dimensions of test pieces

SNI ISO 16981:2012 人造板 表面稳固性的测定

Wood-based panels - Determination of surface soundness

ASTM D7672-11be1 轮辋板产品和组件结构能力评定的标准规范

Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies

ASTM D3043-00(2011) 挠性结构板的标准试验方法

1.1 These test methods determine the flexural properties of strips cut from structural panels or panels up to 4 by 8 ft in size. Structural panels in use include plywood, waferboard, oriented strand board, and composites of veneer and of wood-based layers. Four methods of tests are included: Sections Method A—Center-Point Flexure Test 5 Method B—Two-Point Flexure Test 6 Method C—Pure Moment Test 7 Method D—Flexure Test for Quality Assurance 8 The choice of method will be dictated by the purpose of the test, type of material, and equipment availability. All methods are applicable to material that is relative uniform in strength and stiffness properties. Only Method C should be used to test material suspected of having strength or stiffness variations within a panel caused by density variations, knots, knot-holes, areas of distorted grain, fungal attack, or wide growth variations. However, Method B may be used to evaluate certain features such as core gaps and veneer joints in plywood panels where effects are readily projected to full panels. Method C generally is preferred where size of test material permits. Moments applied to fail specimens tested by Method A, B or D in which large deflections occur can be considerably larger than nominal. An approximate correction can be made. 1.2 Method A, Center-Point Flexure Test—This method is applicable to material that is uniform with respect to elastic and strength properties. Total deflection, and modulus of elasticity computed from it, include a relatively constant component attributable to shear deformation. It is well suited to investigations of many variables that influence properties uniformly throughout the panel in controlled studies and to test small, defect-free control specimens cut from large panels containing defects tested by the large-specimen method. 1.3 Method B, Two-Point Flexure Test—This method, like Method A, is suited to the investigation of factors that influence strength and elastic properties uniformly throughout the panel, in controlled studies, and to testing small, defect free control specimens cut from large specimens tested by Method C. However, it may be used to determine the effects of finger joints, veneer joints and gaps, and other features which can be placed entirely between the load points and whose effects can be projected readily to full panel width. Deflection and modulus of elasticity obtained from this method are related to flexural stress only and do not contain a shear component. Significant errors in modulus of rupture can occur when nominal moment is used (see Appendix X1). 1.4 Method C, Pure Moment Test—This method is ideally suited for evaluating effects of knots, knot-holes, areas of sloping grain, and patches for their effect on standard full-size panels. It is equally well suited for testing uniform or clear material whenever specimen size is adequate. Measured deformation and elastic constants are free of shear deformation effects; and panels can be bent to large deflections without incurring errors from horizontal force components occurring in other methods. Specimen size and span above certain minimums are quite flexible. It is preferred when equipment is available. 1.5 Method D, Flexure Test for Quality Assurance—This method, like Method A, is well suited to the investigation of factors that influence bending strength and stiffness properties. Also like Method A, this method uses small specimens in a center-point simple span test configuration. This method uses a span to depth ratio, specimen width, test fixture and test speed that make the method well suited for quality assurance. The method is frequently used for quality assurance testing of oriented strand board. 1.6 All methods can be used to determine modulus of elasticity with sufficient accuracy. Modulus of rupture determined by Methods A, B or D is subject to errors up to and sometimes exceeding 20 % depending upon span, loading, and deflection at failure unless moment is computed in the rigorous manner outlined in Appendix X1 or corrections are made in other ways. These errors are not present in Method C. 1.7 When comparisons are desired between results of specimen groups, it is good practice to use the same method of test for all specimens, thus eliminating possible differences relatable to test method. 1 These methods are under the jurisdiction of ASTM Committee D07 on Wood and are the direct responsibility of Subcommittee D07.03 on Panel Products. Current edition approved Nov. 1, 2011. Published November 2011. Originally approved in 1972. Last previous edition approved in 2000 as D3043 – 00 (2006). DOI: 10.1520/D3043-00R11. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States 1 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Structural Panels in Flexure

LY/T 1982-2011 人造板及其制品甲醛释放量检测用大气候室

本标准规定了人造板及其制品甲醛释放量检测用大气候室的结构与技术参数、要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于使用大气候室进行人造板及其制品的甲醛释放量检测。

Large chamber for formaldehyde emission of wood-based panels and its products

LY/T 1981-2011 甲醛释放量气体分析法检测箱

本标准规定了甲醛释放量气体分析法检测箱的术语和定义、系统构成与技术参数、要求、负载运转试验、试验方法、技术质量认证和标志、包装、运输、贮存。 本标准适用于使用气体分析法检测人造板及其制品中甲醛释放量的检测箱

Testing apparatus for formaldehyde emission by the gas analysis method

LY/T 1980-2011 挥发性有机化合物及甲醛释放量检测箱

本标准规定了人造板及其制品中挥发性有机化合物（VOC）及甲醛释放量检测箱的术语和定义、系统构成与技术参数、要求、负载运转试验、试验方法、技术质量认证和标志、包装、运输、贮存。 本标准适用于检测人造板及其制品中挥发性有机化合物（VOC）及甲醛释放量的检测箱。

Determination device of the emission of volatile organic compounds and formaldehyde

LY/T 1978-2011 甲醛释放量测定抽吸法

本标准规定了人造板甲醛释放量抽吸法的测定方法。 本标准适用于高密度纤维板、中密度纤维板、地板基材用纤维板和刨花板等。

Wood-based panels-Determination of formaldehyde release-Air exhaust method

ISO 12460-5:2011 木基板材.甲醛释放的测定.第5部分:萃取法(又称穿孔法)

Wood-based panels - Determination of formaldehyde release - Part 5: Extraction method (called the perforator method)

ISO 12460-4:2008/Amd 1:2011 木基板材.甲醛释放的测定.第4部分:干燥器法;修改件1

Wood-based panels - Determination of formaldehyde release - Part 4: Desiccator method; Amendment 1

Wood-based panels - Determination of formaldehyde release - Part 4: Desiccator method; Amendment 1

DS/EN 326-2:2011 人造板 取样、切割和检验 第2部分：初始型式试验和工厂生产控制

This European Standard specifies methods for internal initial type testing (ITT) and internal factory production control (FPC) as well as external control of wood-based panels for their compliance with EN 13986 and other relevant product specifications. However, it may also apply, at the option of the manufacturer, to wood-based panels applied for non-construction purposes.This European Standard is not applicable for the assessment of compliance with specifications of panels comprised in consignments. In such cases, EN 326-3 applies.For factory production control, if required, methods for the assessment of conformity of batches and of production over longer

Wood-based panels - Sampling, cutting and inspection - Part 2: Initial type testing and factory production control

BS EN 326-2:2010 木基板.抽样,切削和检验.初始类型试验和工厂生产控制

Wood-based panels. Sampling, cutting and inspection. Initial type testing and factory production control

BS EN 326-2:2010+A1:2014 人造板 取样、切割和检验 初始型式试验和工厂生产控制

What is BS EN 326-2 – Initial type testing and factory production control of wood-based panels about? BS EN 326-2 discusses wood-based panels. The aim of the BS EN 326-2 is to ensure that the product conforms to the technical specification. BS EN 326-2 is the second part of the BS EN 326 series of standards that specifies methods for internal initial type testing (ITT) and internal factory production control (FPC) as well as external control of wood-based panels for their compliance with BS EN 13986 and other relevant product specifications. However, it may also apply, at the option of the manufacturer, to wood-based panels applied for non-construction purposes.For internal factory production control, if required, methods for the assessment of conformity of batches and of production over longer periods are given. For external control, if required, methods for the initial inspection of a factory and initial type testing of a product, and for the surveillance of the factory production control, are given. In the factory production control small test pieces are used. The statistics of evaluation are based on the normal distribution. Note: BS EN 326-2 is not applicable for the assessment of compliance with specifications of panels comprised in consignments. In such cases, BS EN 326-3 applies. Who is BS EN 326-2 - Initial type testing and factory production control of wood-based panels for ? BS EN 326-2 on wood-based panels is useful for: Wood-based panels manufacturers

Wood-based panels. Sampling, cutting and inspection - Initial type testing and factory production control

LST EN 326-2-2010 人造板 取样、切割和检验 第2部分：初始型式试验和工厂生产控制

Wood-based panels - Sampling, cutting and inspection - Part 2: Initial type testing and factory production control

NF B51-190-2:2010 木基板.取样,切割和检验.第2部分:工厂中的质量控制

Wood-based panels - Sampling, cutting and inspection - Part 2 : initial type testing and factory production control.

DIN EN 326-2:2010 木质板.取样,切割和检验.第2部分:初始类型试验和工厂产品控制.德文版本EN 326-2-2010

Wood-based panels - Sampling, cutting and inspection - Part 2: Initial type testing and factory production control; German version EN 326-2:2010

EN 326-2:2010 木基镶板.抽样,剪切和检验.工厂中的质量控制

This European Standard specifies methods for internal initial type testing (ITT) and internal factory production control (FPC) as well as external control of wood-based panels for their compliance with EN 13986 and other relevant product specifications. However, it may also apply, at the option of the manufacturer, to wood-based panels applied for non-construction purposes.This European Standard is not applicable for the assessment of compliance with specifications of panels comprised in consignments. In such cases, EN 326-3 applies. For internal factory production control, if required, methods for the assessment of conformity of batches and of production over longer periods are given. For external control, if required, methods for the initial inspection of a factory and initial type testing of a product, and for the surveillance of the factory production control, are given. In the factory production control small test pieces are used. The statistics of evaluation is based on normal distribution.

Wood-based panels - Sampling, cutting and inspection - Part 2: Initial type testing and factory production control (Incorporates Amendment A1: 2014)