79.060.01 木基板材综合 标准查询与下载

KS F ISO 16999-2006(2011) 人造板试样的取样和切割

Wood-based panels－Sampling and cutting of test pieces

KS F ISO 16985-2006(2011) 木质板构件的相对湿度的尺寸变化测定方法

Wood-based panels－Determination of dimensional changes associated with changes in relative humidity

ASTM D358-98(2006) 涂料耐候试验中用作面板的木材的标准规范

Standard Specification for Wood to Be Used as Panels in Weathering Tests of Coatings

DIN EN 326-2 Corrigendum 1:2006 木质板. 取样、切割和检验. 第2部分: 工厂中的质量控制; 英文版本DIN EN 326-2: 2000-10勘误表1

Wood-based panels - Sampling, cutting and inspection - Part 2: Quality control in the factory Corrigendum 1 to English version of DIN EN 326-2:2000-10

ASTM D7250/D7250M-06 夹层梁抗弯和剪切刚度测定标准规范

Flexure tests on flat sandwich constructions may be conducted to determine the sandwich flexural stiffness, the core shear strength and shear modulus, or the facings compressive and tensile strengths. Tests to evaluate core shear strength may also be used to evaluate core-to-facing bonds. This practice provides a standard method of determining sandwich flexural and shear stiffness and core shear modulus using calculations involving measured deflections of sandwich flexure specimens. Tests can be conducted on short specimens and on long specimens (or on one specimen loaded in two ways), and the flexural stiffness, shear rigidity and core shear modulus can be determined by simultaneous solution of the complete deflection equations for each span or each loading. If the facing modulus values are known, a short span beam can be tested and the calculated bending deflection subtracted from the beamrsquo;total deflection. This gives the shear deflection from which the transverse shear modulus can be determined. Note 18212;Core shear strength and shear modulus are best determined in accordance with Test Method C 273 provided bare core material is available. Note 28212;For cores with high shear modulus, the shear deflection will be quite small and ordinary errors in deflection measurements will cause considerable variations in the calculated shear modulus. Note 38212;To insure that simple sandwich beam theory is valid, a good rule of thumb for a four-point bending test is the span length divided by the sandwich thickness should be greater than 20 (L1/d > 20) with the ratio of facing thickness to core thickness less than 0.1 (t/c < 0.1).1.1 This practice covers determination of the flexural and transverse shear stiffness properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes. Permissible core material forms include those with continuous bonding surfaces (such as balsa wood and foams) as well as those with discontinuous bonding surfaces (such as honeycomb). The calculation methods in this practice are limited to sandwich beams exhibiting linear force-deflection response. This practice uses test results obtained from Test Methods C 393/C 393M and/or D 7249/D 7249M.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determining Sandwich Beam Flexural and Shear Stiffness

ASTM D7249/D7249M-06 通过长臂梁柔性构造叠合板对接特性的标准试验方法

1.1 This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the facings. Permissible core material forms include those with continuous bonding surfaces (such as balsa wood and foams) as well as those with discontinuous bonding surfaces (such as honeycomb).1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 1 - Alternate procedures for determining the compressive strength of unidirectional polymer matrix composites materials in a sandwich beam configuration may be found in Test Method D 5467.

Standard Test Method for Facing Properties of Sandwich Constructions by Long Beam Flexure

DD CEN/TS 14966:2005 人造板 某些机械性能的小规模指示性试验方法

This Technical Specification specifies small-scale test methods for estimating the following mechanical properties of wood-based panels:  indicative planar shear strength (sometimes referred to as block shear);  indicative panel shear strength;  indicative strength and modulus of elasticity in tension in the plane of the panel;  indicative strength in compression in the plane of the panel. Reference should be made to EN 310 for bending properties. For plywood, EN 314-1 may also be used as an indicator of planar shear strength. These test methods are intended for indicative purposes only and should not be used as a means of determining structural design values. They may not be suitable for all panel types. They may be used as a means of supporting quality control procedures for structural panels, if correlations with EN 789 test results can be established (CEN Technical Report in preparation).

Wood-based panels — Small scale indicative test methods for certain mechanical properties

ISO 20585:2005 木质板材.浸在70度或100度（沸水温度）后测量湿抗弯强度

This International Standard specifies methods for determining the bending strength of particleboards and fibreboards after immersion in hot water. Method A is applicable for water at 70 ℃ and Method B for water at 100 ℃ (boiling temperature). NOTE The boiling temperature can slightly differ depending on the altitude above sea level.

Wood-based panels - Determination of wet bending strength after immersion in water at 70℃ or 100℃ (boiling temperature)

BS DD CEN/TS 14966:2005 木质板材.特定机械特性的小型指示性试验方法

This Technical Specification specifies small-scale test methods for estimating the following mechanical properties of wood-based panels:  indicative planar shear strength (sometimes referred to as block shear);  indicative panel shear strength;  indicative strength and modulus of elasticity in tension in the plane of the panel;  indicative strength in compression in the plane of the panel. Reference should be made to EN 310 for bending properties. For plywood, EN 314-1 may also be used as an indicator of planar shear strength. These test methods are intended for indicative purposes only and should not be used as a means of determining structural design values. They may not be suitable for all panel types. They may be used as a means of supporting quality control procedures for structural panels, if correlations with EN 789 test results can be established (CEN Technical Report in preparation).

Wood-based panels - Small scale indicative test methods for certain mechanical properties

DS/CEN/TS 14966:2005 人造板 某些机械性能的小规模指示性试验方法

This technical specification specifies small-scale test methods for estimating for the following mechanical properties of wood-based panels: indicative planar shear strength, indicative panel shear strength, indicative strength and modulus of elasticity in tension in the plane of the panel, indicative strength and modulus of elasticity in tension in the plane of the panel.

Wood-based panels - Small scale indicative test methods for certain mechanical properties

DIN CEN/TS 14966:2005 木质板材.特定机械特性的小型指示性试验方法

Wood-based panels - Small scale indicative test methods for certain mechanical properties; German version CEN/TS 14966:2005

PD CEN/TS 14966:2005 木质板材.特定机械特性的小型指示性试验方法

This Technical Specification specifies small-scale test methods for estimatingThe following mechanical properties of wood-based panels:indicative planar shear strength (sometimes referred to as block shear); indicative panel shear strength; indicative strength and modulus of elasticity in tension inThe plane of the panel; indicative strength in compression inThe plane of the panel. Reference should be made to EN 310 for bending properties. For plywood, EN 314-1 may also be used as an indicator of planar shear strength.These test methods are intended for indicative purposes only and should not be used as a means of determining structural design values.They may not be suitable for all panel types.They may be used as a means of supporting quality control procedures for structural panels, if correlations with EN 789 test results can be established (CEN Technical Report in preparation).

Wood-based panels - Small scale indicative test methods for certain mechanical properties

BS EN 789:2005 木结构.试验方法.木基护墙板机械特性的测定

Timber structures - Test methods - Determination of mechanical properties of wood based panels

DIN EN 13986:2005 建筑用木质板条.特性、合格评定和标记

This European Standard defines wood-based panels for use in construction and specifies the relevant characteristics and the appropriate test methods to determine these characteristics for wood-based panels, unfaced, overlaid, veneered or coated.#,,#

Wood-based panels for use in construction - Characteristics, evaluation of conformity and marking; German version EN 13986:2004

DS/EN 717-1:2005 人造板甲醛释放量的测定第1部分：箱法甲醛释放量

This European Prestandard specifies a chamber method with three options of test chambers for the determination of the formaldehyde emission from wood-based panels in terms of the steady-state concentration in a climate chamber under defined conditions, which relate to average conditions in real-life. This chamber method can also be applied to the estimation of formaldehyde concentrations under various conditions in practice, by the use of mathematical models.

Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method

DIN EN 789:2005 木结构.试验方法.木基板材机械特性的测定

This standard specifies test methods for determining some mechanical properties of commercial wood-based panel products for use in load-bearing timber structures. These properties are intended for the calculation of characteristic values for use in obtaining material design values. For each type and grade of load-bearing panel product, as defined in the Harmonised Standard for wood-based panels (EN 13986), it is necessary to determine characteristic values of mechanical properties to enable it to be used for structural purposes. This standard details the testing required to establish characteristic values. The tests need only be carried out once for each product, unless there is a reason to suspect a significant change has occurred in the properties of the product.#,,#

Timber structures - Test methods - Determination of mechanical properties of wood based panels; German version EN 789:2004

DIN EN 717-1:2005 木基板材.甲醛释出的测定.第1部分:用燃烧室法测定甲醛的排放量

This European Standard specifies a chamber method with three options of test chambers for the determination of the formaldehyde emission from wood-based panels in terms of the steady-state concentration in a climate chamber under defined conditions, which relate to typical conditions in real-life. This chamber method can also be applied to the estimation of formaldehyde concentrations under various conditions in practice, by the use of mathematical models. This standard can also be used for the testing of formaldehyde emissions of products other than wood-based panels.

Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method; German version EN 717-1:2004

LST EN 717-1-2004 人造板甲醛释放量的测定第1部分：箱法甲醛释放量

Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method

SANS 5970:2004 木板制品的边缘直线度

Specifies a method for the determination of the edge straightness of wooden board products.

Edge straightness of wooden board products

SANS 5969:2004 木板制品的平直度

Specifies a method for the determination of the flatness of wooden board products.

Flatness of wooden board products