81.040.20 建筑玻璃 标准查询与下载

ASTM C1249-18 用于结构密封胶玻璃应用的密封绝缘玻璃单元二次密封标准指南

1.1 This guide covers design and fabrication considerations for the edge seal of conventionally sealed insulating glass units, herein referred to as IG units. The IG units described are used in structural silicone sealant glazing systems, herein referred to as SSG systems. SSG systems typically are either two or four sided, glazed with a structural sealant. Other conditions such as one, three, five, six sided may be used. 1.2 This guides does not cover the IG units of other than conventional edge seal design (Fig. 1); however, the information contained herein may be of benefit to the designers of such IG units. 1.3 In an SSG system, IG units are retained to a metal framing system by a structural seal (Fig. 2). The size and shape of that seal, as well as numerous other SSG system design considerations, are not addressed in this guide. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 The committee with jurisdiction for this standard is not aware of any comparable standard guides published by other organizations. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications

BS 6262-1:2017 建筑物的玻璃 选择玻璃的一般方法

1   Scope This part of BS 6262 gives a general methodology and recommendations for the selection of an appropriate choice of glass, plastics glazing sheet material and method of glazing. These recommendations do not apply to: a) glazing for furniture and fittings (see BS EN 12521 and BS EN 14749); b) glazing for commercial greenhouses (see BS EN 13031‑1); and c) glazing for domestic greenhouses.

Glazing for buildings. General methodology for the selection of glazing

T/ZZB 0277-2017 轻型高透防弹防砸符合玻璃

本标准规定了轻型高透防弹防砸复合玻璃的术语与定义、分类和代号、基本要求、技术要求、试验方法、检验规则、标志、运输、包装与贮存、质量承诺等内容。 本标准适用于平面超白玻璃和聚碳酸酯、聚氨酯透明材料合成的轻型高透防弹防砸复合玻璃。

Light-weight high-transmittance ballistic and forced entry resistant glass

BS 6262-7:2017 建筑物用门窗玻璃.信息提供的实施规则

Glazing for buildings. Code of practice for the provision of information

17/30365062 DC BS EN 14179-2 建筑中的玻璃 热浸热钢化钠钙硅酸盐安全玻璃 第2部分：产品标准

BS EN 14179-2. Glass in building. Heat soaked thermally toughened soda lime silicate safety glass - Part 2. Product standard

17/30365059 DC BS EN 14449 建筑中的玻璃 夹层玻璃和夹层安全玻璃 产品标准

BS EN 14449. Glass in building. Laminated glass and laminated safety glass. Product standard

17/30365055 DC BS EN 12150-2 建筑中的玻璃 热钢化钠钙硅酸盐安全玻璃 第2部分：产品标准

BS EN 12150-2. Glass in building. Thermally toughened soda lime silicate safety glass - Part 2. Product standard

ASTM E3119-17e1 环境控制动态玻璃加速老化的标准试验方法

Standard Test Method for Accelerated Aging of Environmentally Controlled Dynamic Glazing

ISO 18543:2017 建筑玻璃. 电致变色玻璃. 加速老化试验和要求

Glass in building - Electrochromic glazings - Accelerated ageing test and requirements

T/ZBH 001-2017 建筑玻璃外观质量要求及评定

1 范围；2规范性引用文件；3 术语和定义；4 检验及判断项目　；5 要求；6 检验方法；7、检验规则；参考文献　  

The requirements and evaluations of appearance quality of glass in building

ASTM C1265-17 用于确定结构玻璃应用的绝缘玻璃边缘密封件的拉伸性能的标准测试方法

5.1 Frequently IG units are adhered with a structural sealant to a metal framing system. In such applications, only the inward lite of glass is usually adhered to the frame. As a result, a significant portion of any outward-acting or negative wind load must be carried in tension by the joint seal between the two lites of the IG unit. This test will not provide information on the integrity of the IG unit primary seal; however, it may provide data on load sharing between the primary IG vapor seal and the secondary structural sealant. 5.2 Although this test method prescribes one environmental condition, other environmental conditions and exposure cycles can be employed for specific project evaluation. Such deviations should be described when reporting the data. 1.1 This test method covers a laboratory procedure for quantitatively measuring the tensile strength, stiffness, and adhesion properties of insulating glass edge seals that are used in structural sealant glazing applications. Edge seals for these applications use a structural sealant to bond both glass lites and the edge spacer into a monolithic sealed insulating glass unit. In typical applications, the structural sealant acts to hold the outside lite in place under wind and gravity load and to maintain the edge spacer in its proper position. Hereafter, the term “insulating glass” will be abbreviated as “IG.” 1.2 The characterization of the IG secondary sealant properties, as defined by this test method, are strongly dependent on glass and edge spacer cleaning procedures, IG spacer profile, location of spacer, and primary IG sealant application. Users of this test method must recognize that the IG edge seal assembly influences the secondary sealant properties. 1.3 The values determined by this test method will be characteristic of the particular edge seal assembly that is tested. Note 1: Presently, only elastomeric, chemically curing silicone sealants specifically formulated for use as the secondary seal of IG units are recognized as having the necessary durability for use in structural sealant glazing applications. 1.4 The values stated in SI (metric) units are to be regarded as the standard. The inch-pound values given in parentheses are approximate equivalents, provided for information purposes. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications

ASTM E2358-17 永久性栏杆系统 护栏和栏杆玻璃性能标准规范

11.1 The significance and use of the test methods is contained in Test Methods E2353. 1.1 This specification covers glass in permanent railing systems, guards, and balustrades, including components such as rails and swing gates or other forms of required guardrail opening protection installed in agricultural, assembly, commercial, educational, industrial, institutional, recreational, and residential buildings, and other structures such as towers or elevated platforms. 1.2 This specification is intended to be applied to permanent glass or other glazing railing systems for buildings and to such railing systems, rails, guards, and balustrades having major structural components made of glass or other glazing material, or the secondary components such as infill or balusters made of glass or other glazing material. 1.3 This specification considers that the overall outlook is based on the health and safety of all potential users of buildings. The criteria incorporated in this specification provide for normal and anticipated building uses, but not for abuses for which the building and its components are not designed. 1.4 This specification establishes basic minimum requirements and criteria that lead to satisfactory products under normal use conditions and does not give consideration to design criteria for specific field conditions, the establishment of which is the prerogative and responsibility of the designer, specification writer, and regulatory agencies. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Performance of Glazing in Permanent Railing Systems, Guards, and Balustrades

17/30360105 DC BS EN 1748-1-2 建筑中的玻璃 特殊基础产品 硼硅酸盐浮法玻璃 第 1-2 部分 产品标准

BS EN 1748-1-2. Glass in building. Special basic products. Borosilicate float glass. Part 1-2. Product standard

17/30359847 DC BS EN 14178-1 建筑中的玻璃 碱性碱土硅酸盐玻璃产品 第 1 部分：浮法玻璃

BS EN 14178-1. Glass in building. Basic alkaline earth silicate glass products - Part 1. Float glass

17/30359850 DC BS EN 14178-2 建筑中的玻璃 碱性碱土硅酸盐玻璃制品 第二部分：产品标准

BS EN 14178-2. Glass in building. Basic alkaline earth silicate glass products. Part 2. Product standard

ASTM E2751/E2751M-17a 支撑层压玻璃走道的设计和性能标准实践

1.1 This practice addresses elements related to load-bearing glass walkways, glass treads, and glass landings constructed with laminated glass. This standard includes performance, design, and safe behavior considerations. It addresses the characteristics unique to glass and laminated glass. Issues that are common to all walkways, such as slip resistance, are addressed in existing referenced standards. 1.2 This practice does not address glass walkways constructed with monolithic glass, glass block, insulating glass units, glass tiles that are directly bonded to a non-glass structural substrate, or glass walkways intended to support vehicular traffic. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Design and Performance of Supported Laminated Glass Walkways

DIN EN 16477-1:2017 建筑用玻璃.内部使用彩色玻璃.第1部分:要求;德文版本EN 16477-1-2016

Glass in building - Painted glass for internal use - Part 1: Requirements; German version EN 16477-1:2016

ASTM D8040-17 玻璃器皿中传热液体腐蚀试验的标准试验方法

1.1 This test method covers a simple beaker-type procedure for evaluating the effects of heat transfer fluids (HTF) on metal specimens under controlled laboratory conditions. Fluids tested under this method are specifically designed for heating and air conditioning (HVAC) systems. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in 10.1.7.2, 10.1.7.3, 10.1.7.4, and A1.1.6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware

CAN/CGSB-12.8-2017 中空玻璃装置

Insulating Glass Units

CAN/CGSB-12.8-2017(R2022) 中空玻璃单元

This standard applies to sealed insulating glass (IG) units used in windows, doors and curtain walls in building envelopes. It includes requirements for the testing of samples for the integrity and durability of the unit’s hermetic seal and if applicable, gas concentration. The requirements contained herein are applicable to glass units consisting of two or three sheets of glass and glazed in recessed openings so that the edge seals are shielded from direct weathering. The requirements also apply to glass units that may be coated, have muntin bars within the cavities and contain air or argon gas within the cavities. The testing of permanently vented or capillary tube units are not included in this standard. A User’s guide is found in Annex D as an aid in the application of this standard. The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use.

Insulating glass units