81.040.20 建筑玻璃 标准查询与下载

UNI EN 17416-2021 建筑物中的玻璃 危险物质释放的评估 玻璃制品排放到室内空气中的测定

Glass in building - Assessment of release of dangerous substances - Determination of emissions into indoor air from glass products

ASTM C1036-21 平板玻璃标准规格

1.1 This specification covers the requirements for annealed, monolithic flat soda-lime glass supplied as cut sizes or stock sheets. 1.2 This specification is focused upon the quality of flat glass as produced. The specification is applicable for laboratory and field evaluation only to the extent that such evaluation can be carried out in accordance with the test method(s) prescribed herein. 1.3 This specification covers the quality requirements of flat, transparent, clear, low-iron, and tinted glass. This glass is intended to be used primarily for architectural glazing products such as coated glass, insulating glass units, laminated glass, mirrors, and spandrel glass. NOTE 1—Reflective distortion is not addressed in this specification. 1.4 This specification covers the quality requirements of patterned or wired glasses intended to be used primarily for decorative and general glazing applications. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Flat Glass

JIS R 3110:2021 建筑玻璃摆锤冲击试验方法

Pendulum impact test method for glass in building

OENORM EN 15434-1-2021 粘合密封剂 第1部分：粘合玻璃密封剂

Bonding sealants - Part 1: Bonded glazing sealants

OENORM EN 17635-2021 建筑物中的玻璃 破碎特性 要求和评估方法

Glass in buildig - Shatter properties - Requirements and assessment methods

21/30427952 DC BS EN 17635 建筑中的玻璃 粉碎属性 要求及考核方法

BS EN 17635. Glass in building. Shatter properties. Requirements and assessment methods

DB11/T 1812-2020 既有玻璃幕墙安全性检测与鉴定技术规程

Technical regulations for safety testing and identification of existing glass curtain walls

KS L 2018-2020 玻璃 铅和镉的测定 电感耦合等离子体发射光谱法

Glass — Determination of lead and cadmium — Inductively coupled plasma emission spectrometric method

KS L 2019-2020 玻璃 六价铬的测定

Glass — Determination of hexavalent chromium

T/ZZB 2003-2020 建筑用低辐射镀膜玻璃

本文件规定了建筑用低辐射镀膜玻璃的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则及包装、标志、贮存和运输及质量承诺。 本文件适用于建筑用低辐射镀膜玻璃。

Low emissivity coated glass for building

LST EN 15998-2020 建筑物中的玻璃 火灾时的安全性、耐火性 用于分类目的的玻璃测试方法

Glass in building - Safety in case of fire, fire resistance - Glass testing methodology for the purpose of classification

NF P78-477-1:2020 建筑玻璃. 第1部分: 具有防晒功能的垂直中空玻璃封边部件温度和力的计算

Le présent document s'applique au calcul des températures des composants et des efforts dans les joints de scellement des vitrages isolants verticaux avec protection solaire.Il couvre tous les types de vitrages isolants rectangulaires (double ou triple vitrages) associés à une pr

Glass in Building - Part 1 : calculation of component temperatures and forces in the edge seal of vertical insulating glass units with solar protection

BS EN 12150-1:2015+A1:2019 建筑物中的玻璃 热钢化钠钙硅酸盐安全玻璃 定义和描述

Glass in building. Thermally toughened soda lime silicate safety glass. Definition and description

ISO 22509:2020 建筑玻璃热增强钠钙硅酸盐玻璃

This document specifies product definitions, product characteristics (i.e. tolerances, flatness, edgework), fracture characteristics, including fragmentation, and the physical and mechanical characteristics of flat heat strengthened soda lime silicate glass for use in buildings. This document does not cover surface finished glasses (e.g. sandblasted, acid etched) after heat strengthening. This document does not cover curved (bent) glass. Other requirements, not specified in this document, can apply to heat strengthened soda lime silicate glass which is incorporated into assemblies (e.g. laminated glass or insulating glass units), or undergoes an additional treatment (e.g. coating). The additional requirements are specified in the appropriate glass product standard. Heat strengthened soda lime silicate glass, in this case, does not lose its mechanical or thermal characteristics.

Glass in building — Heat strengthened soda lime silicate glass

ASTM C724-91(2020) 陶瓷装饰品在建筑玻璃上耐酸性的标准试验方法

1.1 This test method covers qualitative determination of the acid resistance of the ceramic decoration on architectural glass. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Acid Resistance of Ceramic Decorations on Architectural-Type Glass

ASTM C1422/C1422M-20a 化学强化扁平玻璃的标准规格

1.1 This specification covers the requirements for chemically strengthened glass products that are used in general building construction, transportation, solar, and other electronic applications, such as PC screens, notebooks, tablets, smart phones, and E-readers, as well as copy machine scanners, computer disks, and flat glass screens for television monitors. The technique covered in this specification usually involves conducting ion exchange of constituent alkali ions in a glass product by immersing it in a bath of molten salt containing larger alkali ions. Penetration of the larger ions into smaller host sites produces a layer of compression on the surface which strengthens the glass. Techniques such as ion implantation, dealkalization, etch-strengthening, and glaze coatings are specifically excluded from this specification. 1.2 Classification of chemically strengthened glass products is based on the laboratory measurements of surface compression and case depth (depth of compression) and not on the modulus of rupture (MOR). This specification does not purport to address end-use performance. 1.3 A test method for the measurement of case depth and surface compression is included in Section 8. Another test method for similar measurement using optically guided-wave equipment is included in Section 9. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Chemically Strengthened Flat Glass

ASTM E2431-12(2020) 确定单层玻璃退火建筑平板玻璃对热负荷的阻力的标准实践

1.1 This practice covers a procedure to determine the resistance of annealed architectural flat glass to thermally induced stresses caused by exposure to sun and shadows for a specified probability of breakage (Pb). Proper use of this procedure is intended to reduce the possibility of thermal breakage of annealed glass in buildings. 1.2 This practice applies to vertical or sloped glazing in buildings. 1.3 This practice applies to monolithic and laminated glass of rectangular shape and assumes that all glass edges are simply supported. 1.4 This practice applies only to annealed flat soda-lime silica glass with clean cut, seamed, flat ground, or ground and polished edges that are free from damage. The glass may be clear or tinted as well as coated (not including coatings that reduce emissivity of the glass). 1.5 This practice does not apply to any form of wired, patterned, etched, sandblasted, drilled, notched, or grooved glass or glass with surface and edge treatments, other than those described in 1.4, that alter the glass strength. 1.6 This practice does not address uniform loads such as wind and snow loads, safety requirements, fire, or impact resistance. 1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. For conversion of quantities in various systems of measurements to SI units, refer to IEEE/ASTM SI-10. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining the Resistance of Single Glazed Annealed Architectural Flat Glass to Thermal Loadings

ASTM E2953-14(2020)e1 用于评估密封绝缘玻璃单元中电致变色器件加速老化性能的标准规范

1.1 This specification is applicable to all electrochromic (EC) glass whose visible light transmittance or near infrared light transmittance properties, or both, can be changed reversibly by the application or removal of an electrical voltage. This includes absorptive and reflective EC devices. 1.2 This specification does not apply to other types of dynamic glass which do not solely require an electrical stimulus to change light transmittance such as photochromic and thermochromic glazings and hybrid active/passive chromogenics. 1.3 This specification covers electrochromic devices in preassembled permanently sealed insulting glass units with one or more cavities in which at least one lite contains an EC device (which may be in the form of a laminated lite or a single pane with coatings applied). This specification is also applicable to EC devices in preassembled insulating glass units with capillary tubes intentionally left open. As such this specification also requires conformance to Specification E2190. 1.4 This specification is applicable only to sealed insulating glass units that are constructed with glass and fabricated for vision glass areas for use in buildings, such as sliding doors, windows, skylights, and exterior wall systems. 1.5 Qualification under this specification is intended to provide a basis for evaluating the aging performance of electrochromic devices in sealed insulating glass units. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Evaluating Accelerated Aging Performance of Electrochromic Devices in Sealed Insulating Glass Units

BS ISO 16936-1:2020 建筑中的玻璃 强行进入安全玻璃 通过重复落球测试和分类

What is ISO 16936 ‑ 1 about?    ISO 16936 ‑ 1 is the first part of a multi-series of documents on forced-entry security glazing.   ISO 16936 ‑ 1 specifies requirements and a test method for security glazing designed to resist the impacts of a hard body by delaying access of objects and/or persons to a protected space for a short period of time. It also classifies security-glazing products into categories of resistance to repetitive impacts of a steel sphere.   In

Glass in building. Forced-entry security glazing - Test and classification by repetitive ball drop

ASTM C1394-20 原位结构硅胶玻璃评估标准指南

1.1 The existing condition of SSG installations should be periodically evaluated in-situ to detect if problems exist, and if so found, to address them before they become severe or pervasive. Evaluation of existing SSG installations is required by certain building codes and local ordinances. This guide provides a program to evaluate the existing conditions, lists typical conditions that may exist, and suggests times when such evaluations are appropriate. Presently, only a silicone sealant that is specifically formulated, tested and marketed as a structural glazing sealant is allowed for structural sealant glazing. The committee with jurisdiction over this standard is not aware of any comparable standards published by any other organizations. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for In-Situ Structural Silicone Glazing Evaluation