81.060.99 有关陶瓷的其他标准 标准查询与下载

GB/T 2836-1998 陶管水压试验方法

本标准规定了陶管水压试验的试样、试验装置、试验步骤及试验报告等。 本标准适用于陶管在一定水压下的抗渗透性检验。

Test method for hydrostatic proof of vitrified clay pipe

GB/T 2835-1998 陶管耐酸性能试验方法

本标准规定了陶管耐酸性能试验的试样设备、仪器设备和试剂、试验步骤、结果计算、复验规则及试验报告等。 本标准适用于带釉或不带釉陶管的耐酸性能试验。耐酸性能的优劣用耐酸度来表示。

Test method for acid resistance of vitrified clay pipe

GB/T 2834-1998 陶管吸水率试验方法

本标准规定了陶管吸水率试验的试样、试验仪器、试验步骤、结果计算及试验报告等。 本标准适用于陶管的吸水率试验。

Test method for water absorbtion of vitrified clay pipe

GB/T 2837-1998 陶管尺寸及偏差测量方法

本标准规定了陶管尺寸及偏差测量所需试样、测量工具、测量方法及检验报告。 本标准适用于陶管尺寸及偏差的测量。

Measuring method for size and deviation of vitrified clay pipe

JB/T 14235-2023 铸造浇注系统用陶瓷管

Ceramic tubes for casting pouring systems

DB4103/T 156-2023 新安窑品制作技艺 紫砂壶

Xin'an Kiln Production Techniques Purple Clay Pot

DB4103/T 155-2023 新安窑品制作技艺 澄泥砚

Xin'an kiln product production technology Chengni inkstone

T/CI 188-2023 熔模精密铸造硅基陶瓷型芯设计规范

本文件规定了硅基陶瓷型芯特征结构设计要求、使用性能设计要求和模具设计要求。 本文件适用于高温合金、不锈钢、钛合金等多种合金材料熔模精密铸造中使用硅基陶瓷型芯的制造工艺设计参考。

The design specifications of silica-based ceramic cores for investment casting

T/CIET 212-2023 陶瓷平板膜污水处理技术规范

本文件规定了陶瓷平板膜污水处理技术的术语和定义、总体要求、设计水量和水质要求、技术要求、工艺检测和过程控制、辅助工程设计、施工、性能试验、工程验收、运行管理和维护等内容。 本文件适用于陶瓷平面膜污水处理技术要求。

Technical Specifications for Ceramic Flat Membrane Wastewater Treatment

ASTM C1211-18(2023) 高温下高级陶瓷抗弯强度的标准试验方法

1.1 This test method covers determination of the flexural strength of advanced ceramics at elevated temperatures.2 Four-point-1⁄4-point and three-point loadings with prescribed spans are the standard as shown in Fig. 1. Rectangular specimens of prescribed cross-section are used with specified features in prescribed specimen-fixture combinations. Test specimens may be 3 by 4 by 45 to 50 mm in size that are tested on 40-mm outer span four-point or three-point fixtures. Alternatively, test specimens and fixture spans half or twice these sizes may be used. The test method permits testing of machined or as-fired test specimens. Several options for machining preparation are included: application matched machining, customary procedures, or a specified standard procedure. This test method describes the apparatus, specimen requirements, test procedure, calculations, and reporting requirements. The test method is applicable to monolithic or particulateor whisker-reinforced ceramics. It may also be used for glasses. It is not applicable to continuous fiberreinforced ceramic composites. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Flexural Strength of Advanced Ceramics at Elevated Temperatures

T/GIEHA 037-2022 品牌评价 健康陶瓷

6　健康指标评价及试验方法 基础指标 陶瓷产品质量应符合GB/T 4100、GB/T 23266等标准的相关要求。瓷质砖产品应通过国家强制性认证。 陶瓷产品的放射性应符合GB 6566中A类装饰装修材料的要求。 健康指标 陶瓷产品的健康指标评价及分值管理见表1，总分为340分。 表1　健康陶瓷健康评价指标及分值管理 序号　项目　指标　试验方法　单位　评分 1　甲醛净化效率（r）　r≥90 　 按QB/T 2761规定的方法进行　 % 　85分 　　80≤r≤90　　　75分 　　75≤r≤80 　　　65分 2　持久甲醛净化效率（x）　x≥90　 按T/CSTM 00228.1-2021中第8.7章规定的方法进行检测 　　60分 　　80≤x≤90　　　50分 　　70≤x≤80　　　40分 　　60≤x≤70　　　30分 3　抗菌率（R）　R≥95　 按JC/T 897规定的方法进行　　70分 　　93≤R≤95　　　64分 　　90≤R≤93　　　58分 4　抗菌耐久率（K）　≥95　　　65分 　　90≤K≤95　　　60分 　　85≤K≤90　　　55分 5　负离子（C）　C≥1500　 按照T/CBCSA 14规定的方法进行　 个/cm3　60分 　　800≤C≤1500　　　40分 　　500≤C≤800　　　20分 

Brand evaluation Health ceramics

ASTM C1292-22 环境温度下连续纤维增强高级陶瓷剪切强度的标准试验方法

1.1 This test method covers the determination of shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at ambient temperature. The test methods addressed are (1) the compression of a double-notched test specimen to determine interlaminar shear strength, and (2) the Iosipescu test method to determine the shear strength in any one of the material planes of laminated composites. Test specimen fabrication methods, testing modes (load or displacement control), testing rates (load rate or displacement rate), data collection, and reporting procedures are addressed. 1.2 This test method is used for testing advanced ceramic or glass matrix composites with continuous fiber reinforcement having unidirectional (1D) or bidirectional (2D) fiber architecture. This test method does not address composites with 3D fiber architecture or discontinuous fiber-reinforced, whiskerreinforced, or particulate-reinforced ceramics. 1.3 The values stated in SI units are to be regarded as the standard and are in accordance with IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 8.1 and 8.2. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Shear Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures

ASTM C1259-21 用振动脉冲激励法测定高级陶瓷动态杨氏模量、剪切模量和泊松比的标准试验方法

1.1?This test method covers determination of the dynamic elastic properties of advanced ceramics at ambient temperatures. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test spec

Standard Test Method for Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio for Advanced Ceramics by Impulse Excitation of Vibration

ASTM C1466-00(2020) 石墨炉原子吸收光谱法测定陶瓷食品中铅和镉的标准测试方法

1.1 This test method covers procedures for using graphite furnace atomic absorption spectroscopy (GFAAS) to quantitatively determine lead and cadmium extracted by acetic acid at room temperature from the food-contact surface of foodware. The method is applicable to food-contact surfaces composed of silicate-based materials (earthenware, glazed ceramicware, decorated ceramicware, decorated glass, and lead crystal glass) and is capable of determining lead concentrations greater than 0.005 to 0.020 µg/mL and cadmium concentrations greater than 0.0005 to 0.002 µg/mL, depending on instrument design. 1.2 This test method also describes quality control procedures to check for contamination and matrix interference during GFAAS analyses and a specific sequence of analytical measurements that demonstrates proper instrument operation during the time period in which sample solutions are analyzed. 1.3 Cleaning and other contamination control procedures are described in this test method. Users may modify contamination control procedures provided that the modifications produce acceptable results and are used for both sample and quality control analyses. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Graphite Furnace Atomic Absorption Spectrometric Determination of Lead and Cadmium Extracted From Ceramic Foodware

T/CSTM 00254-2020 聚碳硅烷裂解产物氧含量的测定 脉冲加热惰气熔融-红外线吸收法

本标准规定了使用脉冲加热惰气熔融-红外线吸收法测定聚碳硅烷裂解产物中的氧含量，包含原理、试剂与材料、仪器与设备、样品制备、仪器参数、分析步骤、结果表述、分析结果的采用和试验报告等内容。 本标准适用于液态或固态聚碳硅烷完全裂解后氧含量的测定，测定范围（质量分数）为0.5~5.0%。 质量分数超出范围之外的氧含量测定，可参考使用。

The pyrolysis products of polycarbosilane–Determination of oxygen by the pulse heating insert gas fusion-infra-red absorption method

ASTM C1274-12(2020) 用物理吸附法测定高级陶瓷比表面积的标准试验方法

1.1 This test method covers the determination of the surface area of advanced ceramic materials (in a solid form) based on multilayer physisorption of gas in accordance with the method of Brunauer, Emmett, and Teller (BET) (1)2 and based on IUPAC Recommendations (1984 and 1994) (2, 3). This test method specifies general procedures that are applicable to many commercial physical adsorption instruments. This test method provides specific sample outgassing procedures for selected common ceramic materials, including: amorphous and crystalline silicas, TiO2, kaolin, silicon nitride, silicon carbide, zirconium oxide, etc. The multipoint BET (1) equation along with the single-point approximation of the BET equation are the basis for all calculations. This test method is appropriate for measuring surface areas of advanced ceramic powders down to at least 0.05 m2 (if in addition to nitrogen, krypton at 77.35 K is utilized as an adsorptive). 1.2 This test method does not include all existing procedures appropriate for outgassing of advanced ceramic materials. However, it provides a comprehensive summary of procedures recommended in the literature for selected types of ceramic materials. The investigator shall determine the appropriateness of listed procedures. 1.3 The values stated in SI units are to be regarded as standard. State all numerical values in terms of SI units unless specific instrumentation software reports surface area using alternate units. In this case, provide both reported and equivalent SI units in the final written report. It is commonly accepted and customary (in physical adsorption and related fields) to report the (specific) surface area of solids as m2 /g and, as a convention, many instruments (as well as certificates of reference materials) report surface area as m2 g–1 , instead of using SI units (m2 kg–1 ). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Advanced Ceramic Specific Surface Area by Physical Adsorption

T/IFP 003-2020 陶 瓷 磨 球 磨 耗 率 检 测 方 法

本标准规定了磨耗检测的过程和具体的方法，以磨耗趋于稳定后的数值为磨耗值，以时间序列的磨耗数值的非线性回归系数k为磨耗加速度，从而更全面的分析了磨球的磨耗性能。

Wear Rate Testing Method of Ceramic Grinding Ball

T/SDQE 012-2019 泰山品质 含锆陶瓷纤维毯

本标准规定了泰山品质含锆陶瓷纤维毯的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于工业热力设备、窑炉和高温管道等绝热、耐火用含锆陶瓷纤维毯。

Taishan quality zirconium ceramic fiber blanket

DB61/T 1228-2019 秦紫玉

本标准适用于秦紫玉原料检验

Qin Ziyu

T/CNIA 0014-2019 多晶硅生产用瓷环

本标准规定了多晶硅生产用氮化硅瓷环的分类、要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书和订货单（或合同）内容。 本标准适用于多晶硅生产用氮化硅瓷环(以下简称瓷环)。

Porcelain rings for polysilicon production