83.040.20 橡胶合成配料 标准查询与下载

T/CSTM 00513-2021 橡胶助剂 预分散母胶粒 MBT-80

本文件规定了橡胶助剂 预分散母胶粒MBT-80的术语和定义、分类和编码、理化性能、组批规则、采样、试验方法、标志、包装、运输和贮存等内容。 本文件适用于橡胶助剂 预分散母胶粒MBT-80的检验。

Rubber additives –Predispersed masterbatch- MBT-80

T/CSTM 00512-2021 橡胶助剂 预分散母胶粒 CBS-80

本文件规定了橡胶助剂预分散母胶粒CBS-80的术语和定义、分类和编码、理化性能、组批规则、采样、试验方法、标志、包装、运输和贮存等内容。 本文件适用于橡胶助剂预分散母胶粒CBS-80的检验。

Rubber additives –Predispersed masterbatch - CBS-80

T/CSTM 00511-2021 印制电路板清洗用消泡剂 消抑泡性能的测试方法

本文件规定了印制电路板清洗在去膜和显影阶段用消泡剂消抑泡性能的测试方法。 本文件适用于印制电路板清洗去膜和显影阶段时，所用消泡剂消泡及抑泡性能的测试。

Defoamer for printed circuit board cleaning—Test method for defoaming and antifoaming performance

T/CSTM 00510-2021 水性涂料用消泡剂 消抑泡性能的测试方法

本文件规定了水性涂料行业用消泡剂消抑泡性能的测试方法。 本文件适用于消泡剂用于水性涂料行业中，消抑泡性能的测试。

Defoamer for paint and coating —Test method for defoaming and antifoaming performance

GSO ASTM D1765:2021 橡胶产品用炭黑的标准分类系统

1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure of a typical rubber compound containing the black. The second character gives information on the average surface area of the carbon black. The last two characters are assigned arbitrarily. 1.2 All rubber-grade carbon blacks for which a number is currently assigned at the time of publication of this classification system are listed in Table 1 together with some of their typical properties. ASTM classification numbers (“N” or “S” designation) not listed in Table 1 have either been withdrawn or are not currently assigned. The use of inactive or unassigned N or S designations is prohibited until such a time as the designation is officially reactivated or assigned by Subcommittee D24.41 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System for Carbon Blacks Used in Rubber Products

GSO ISO 15825:2021 橡胶配合料 炭黑 盘式离心机光沉降法测定骨料粒径分布

ISO 15825:2017 specifies a method for determining the size distribution of carbon black aggregates, using a disc centrifuge photosedimentometer. This technique is based on the hydrodynamic behaviour of carbon black in a centrifugal field. The determination of the aggregate size distribution is important in the evaluation of carbon black used in the rubber industry.

Rubber compounding ingredients — Carbon black — Determination of aggregate size distribution by disc centrifuge photosedimentometry

ASTM D2116-16(2021) FEP树脂模塑和挤压材料的标准规范

1.1 This specification covers melt processable molding and extrusion materials of FEP resin. This specification does not cover recycled FEP materials. These FEP resins are copolymers of tetrafluoroethylene and hexafluoropropylene or modified FEP resins containing no more than 2 % by weight of other fluoromonomers. 1.2 The values stated in SI units as detailed in IEEE/ ASTM SI-10 are to be regarded as the standard. The values given in parentheses are for information only. NOTE 1—Although this specification and ISO 12086-1 and ISO 12086-2 differ in approach or detail, data obtained using either are technically equivalent. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for FEP Resin Molding and Extrusion Materials

ASTM D3493-21 压缩样品（COAN）的炭黑吸油量的标准试验方法

1.1?This test method covers the procedure for the mechanical compression of a carbon black sample and the determination of the oil absorption number of the compressed sample. 1.2?The values stated in SI units are to be regarded as the standard. The values given in parentheses a

Standard Test Method for Carbon Black—Oil Absorption Number of Compressed Sample (COAN)

ASTM D1510-21 炭黑碘吸附值的标准试验方法

1.1?This test method covers the determination of the iodine adsorption number of carbon black. 1.1.1?Method A is the original test method for this determination and Method B is an alternate test method using automated sample processing and analysis. 1.2?The iodine adsorption n

Standard Test Method for Carbon Black—Iodine Adsorption Number

ASTM D1512-21 炭黑pH值的标准测试方法

1.1?These test methods, Test Method A—Boiling Slurry and Test Method B—Sonic Slurry, are used to indicate the pH of the carbon black surface by measuring the pH of water in contact with the carbon black. Note 1:?The pH of the carbon black is often used in this industry to indica

Standard Test Methods for Carbon Black—pH Value

ASTM D3265-21 炭黑标准试验方法 - 着色强度

1.1?This test method covers the determination of the tint strength of carbon black relative to an industry tint reference black (ITRB). 1.2?The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3?This stan

Standard Test Method for Carbon Black—Tint Strength

ASTM D4583-21 从过程控制数据分析计算过程指数的炭黑标准实施规程

1.1 This practice covers (1) a statistical procedure for analyzing the test data generated in the statistical process control of a carbon black manufacturing process; (2) a format for reporting process capability determined from the analysis of control chart data of an individual production run, and (3) a format for reporting process performance determined from the analysis of control chart data of an individual production run. 1.2 This practice specifically applies to the analysis of pelleted carbon black samples taken during the manufacturing process prior to storage. This practice does not apply to shipment samples taken from hopper cars or other containers or packages. 1.3 This practice is specifically designed to be used for those test methods given in Classification D1765 which specify target values. However, these techniques are applicable to other test methods on carbon black. 1.4 This practice describes the calculation for two methods of determining capability factors from an analysis of process control data. 1.4.1 Process capability (Cp) is a measurement of variation calculated from the process control chart data with the use of an estimated standard deviation (σ̂) from the mean value of the moving range (R) chart. The calculation of the process capability (Cp and Cpk) indexes can be used as historical information or to predict future performance of the process, but are only valid when the process is in a state of statistical control. 1.4.2 Process performance (Pp) is a measurement of variation calculated from the process control chart data using sample standard deviation(s). The calculation of the process performance (Pp and Ppk) indexes are used for a historical reference of a process’ performance and does not require a state of statistical control. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Carbon Black—Calculation of Process Indexes From an Analysis of Process Control Data

KS M 6634-2021 橡胶配合剂的试验方法

Testing methods for rubber compounding ingredients

KS M ISO 1138-2021 橡胶配合料 炭黑 硫含量的测定

Rubber compounding ingredients－Carbon black－Determination of sulfur content

KS M ISO 6209-2021 橡胶配合料 炭黑 溶剂可萃取物质的测定

Rubber compounding ingredients－Carbon black－Determination of solvent-extractable material

KS M ISO 1435-2021 橡胶配合料 炭黑（粒状） 细粉含量的测定

Rubber compounding ingredients－Carbon black(pelletized)－Determination of fines content

KS M 6767-2021 石油油品的橡胶化合物的分类

Classification of petroleum oils for rubber compounds

HG/T 5834-2021 硫化促进剂 双（O,O－二丁基二硫代磷酸）锌 (ZDBP)

Vulcanization accelerator zinc bis(O,O-dibutyl dithiophosphate) (ZDBP)

HG/T 5835-2021 硫化促进剂 双[O-丁基-O-（2－乙基己基）二硫代磷酸]锌 ( ZEHBP)

Vulcanization accelerator bis[O-butyl-O-(2-ethylhexyl)dithiophosphate]zinc (ZEHBP)

HG/T 5781-2021 橡胶增塑剂 高粘度矿物油

Rubber plasticizer high viscosity mineral oil