91.010.30 技术方面 标准查询与下载

T/CCIAT 0056-2023 3MW及以下风力发电机保护性拆除施工技术标准

本标准的主要技术内容是：1.总则；2.术语；3.施工准备；4.风力发电机组构件拆除；5.施工管理；附录。

Technical standards for protective dismantling of wind turbines of 3MW and below

T/CCIAT 0054-2023 大体积重晶石泵送混凝土技术规程

本文件的主要技术内容是：1.总则；2.术语；3.基本规定；4.设计；5.混凝土；6.施工；7.质量检验与工程验收。

Technical regulations for large volume barite pumping concrete

T/JNXXH 0026-2023 工程建设数字化系统技术规程

本文件规定了工程建设数字化系统建设总则以及综合管理、质量管理、安全管理、文明施工管理、施工扬尘管理的业务数据与功能要求。

Engineering Construction Digital System Technical Regulations

T/ZPP 010-2023 绿色建筑工程施工技术规范

本文件规定了绿色建筑工程施工的术语和定义、基本规定、建筑材料选择和使用、节能施工措施、室内环境质量管理、建筑废弃物处理、施工过程监控和管理、安全与环保培训等内容。 本文件适用于新建、改建和扩建的绿色建筑工程。

Technical specification for green building engineering construction

DB6501/T 048-2023 绿色建筑室内环境污染物控制规范

本文件适用于绿色建筑室内环境污染物的控制。

Specifications for the control of indoor environmental pollutants in green buildings

DB1310/T 306-2023 废旧混凝土再生集料加工技术规程

本文件适用于废旧混凝土再生集料的加工

Technical regulations for processing recycled aggregates from waste concrete

EN 1999-1-3:2023 欧洲法规9:铝结构的设计.第1-3部分:易疲劳的结构

1.1 Scope of EN 1999-1-3 (1) This document gives the basis for the design of aluminium alloy structures subject to fatigue in the ultimate limit state. (2) This document gives rules for: - safe life design; - damage tolerant design; - design assisted by testing. (3) This document does not cover pressurized containment vessels or pipework. 1.2 Assumptions (1) The general assumptions of EN 1990 apply. (2) The provisions of EN 1999-1-1 apply. (3) EN 1999-1-3 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), relevant parts in EN 1992 to EN 1999, EN 1090-1 and EN 1090-3 for requirements for execution, and ENs, EADs and ETAs for construction products relevant to aluminium structures.

Eurocode 9 - Design of aluminium structures - Part 1-3: Structures susceptible to fatigue

EN 1999-1-5:2023 欧洲法规9的英国国家附录.铝结构设计.第1-5部分:壳层结构

1.1 Scope of EN 1999-1-5 (1) EN 1999-1-5 applies to the structural design of aluminium structures, stiffened and unstiffened, that have the form of a shell of revolution or of a round panel in monocoque structures. (2) EN 1999-1-5 covers additional provisions to those given in the relevant parts of EN 1999 for design of aluminium structures. NOTE Supplementary information for certain types of shells is given in EN 1993-1-6 and the relevant application parts of EN 1993 which include: - Part 3-1 for towers and masts; - Part 3-2 for chimneys; - Part 4-1 for silos; - Part 4-2 for tanks; - Part 4-3 for pipelines. (4) The provisions in EN 1999-1-5 apply to axisymmetric shells (cylinders, cones, spheres) and associated circular or annular plates, beam section rings and stringer stiffeners, where they form part of the complete structure. (5) Single shell panels (cylindrical, conical or spherical) are not explicitly covered by EN 1999-1-5. However, the provisions can be applicable if the appropriate boundary conditions are duly taken into account. (6) Types of shell walls covered in EN 1999-1-5 can be (see Figure 1.1): - shell wall constructed from flat rolled sheet with adjacent plates connected with butt welds, termed “isotropic”; - shell wall with lap joints formed by connecting adjacent plates with overlapping sections, termed “lap-jointed”; - shell wall with stiffeners attached to the outside, termed “externally stiffened” irrespective of the spacing of stiffeners; - shell wall with the corrugations running up the meridian, termed “axially corrugated”; - shell wall constructed from corrugated sheets with the corrugations running around the shell circumference, termed “circumferentially corrugated”. [Figure 1.1 - Illustration of cylindrical shell form] (7) The provisions of EN 1999-1-5 are intended to be applied within the temperature range defined in EN 1999-1-1. The maximum temperature is restricted so that the influence of creep can be neglected. For structures subject to elevated temperatures associated with fire, see EN 1999-1-2. (8) EN 1999-1-5 does not cover the aspect of leakage. 1.2 Assumptions (1) The general assumptions of EN 1990 apply. (2) The provisions of EN 1999-1-1 apply. (3) The design procedures are valid only when the requirements for execution in EN 1090-3 or other equivalent requirements are complied with. (4) For the design of new structures, EN 1999 is intended to be used, for direct application, together with EN 1990, EN 1991, EN 1992, EN 1993, EN 1994, EN 1995, EN 1997 and EN 1998. (5) EN 1999 is intended to be used in conjunction with: - European Standards for construction products relevant for aluminium structures; - EN 1090-1, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components; - EN 1090-3, Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures.

Eurocode 9 - Design of aluminium structures - Part 1-5: Shell structures

EN 1990:2023 欧洲法规.建筑设计基础

Scope of FprEN 1990 (1) This document establishes principles and requirements for the safety, serviceability, robustness and durability of structures, including geotechnical structures, appropriate to the consequences of failure. (2) This document is intended to be used in conjunction with the other Eurocodes for the design of buildings and civil engineering works, including temporary structures. (3) This document describes the basis for structural and geotechnical design and verification according to the limit state principle. (4) The verification methods in this document are based primarily on the partial factor method. NOTE 1 Alternative methods are given in the other Eurocodes for specific applications. NOTE 2 The Annexes to this document also provide general guidance concerning the use of alternative methods. (5) This document is also applicable for: - structural assessment of existing structures; - developing the design of repairs, improvements and alterations; - assessing changes of use. NOTE Additional or amended provisions can be necessary. (6) This document is applicable for the design of structures where materials or actions outside the scope of EN 1991 (all parts) to EN 1999 (all parts) are involved. NOTE In this case, additional or amended provisions can be necessary. 1.2 Assumptions (1) It is assumed that reasonable skill and care appropriate to the circumstances is exercised in the design, based on the knowledge and good practice generally available at the time the structure is designed. (2) It is assumed that the design of the structure is made by appropriately qualified and experienced personnel. (3) The design rules provided in the Eurocodes assume that: - execution will be carried out by personnel having appropriate skill and experience; - adequate control and supervision will be provided during design and execution of the works, whether in factories, plants, or on site; - construction materials and products will be used in accordance with the Eurocodes, in the relevant product and execution standards, and project specifications; - the structure will be adequately maintained; - the structure will be used in accordance with the design assumptions. NOTE Guidance on management measures to satisfy the assumptions for design and execution is given in Annex B.

Eurocode - Basis of structural and geotechnical design

EN 1999-1-4:2023 欧洲法规9.铝结构件的设计.第1-4部分:冷成型结构薄板

1.1 Scope of EN 1999-1-4 (1) EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. NOTE 1 The rules in this part complement the rules in other parts of EN 1999-1. NOTE 2 The execution of aluminium structures made of cold-formed structures for roof, ceiling, floor and wall applications is covered in EN 1090-5. (2) EN 1999-1-4 gives methods for stressed-skin design using aluminium sheeting as a structural diaphragm. (3) EN 1999-1-4 does not apply to cold-formed aluminium profiles like C- and Z- profiles nor cold-formed and welded circular or rectangular hollow sections. (4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing. (5) EN 1999-1-4 does not cover load arrangement for loads during execution and maintenance. 1.2 Assumptions (1) For the design of new structures, EN 1999 is intended to be used, for direct application, together with EN 1990, EN 1991, EN 1992, EN 1993, EN 1994, EN 1995, EN 1997 and EN 1998. EN 1999 is intended to be used in conjunction with: - European Standards for construction products relevant for aluminium structures; - EN 1090-1, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components; - EN 1090-5, Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications.

Eurocode 9 - Design of aluminium structures - Part 1-4: Cold-formed structural sheeting

EN 1999-1-1:2023 欧洲法规9:铝结构的设计.第1部分:一般结构规则

1.1 Scope of FprEN 1999-1-1 (1) FprEN 1999-1-1 gives basic design rules for structures made of wrought aluminium alloys and limited guidance for cast alloys (see Clause 5 and Annex C). This document does not cover the following, unless otherwise explicitly stated in this document: - components with material thickness less than 0,6 mm; - welded components with material thickness less than 1,5 mm; - connections with: - steel bolts and pins with diameter less than 5 mm; - aluminium bolts and pins with diameter less than 8 mm; - rivets and thread forming screws with diameter less than 3,9 mm. 1.2 Assumptions (1) In addition to the general assumptions of EN 1990 the following assumptions apply: - execution complies with EN 1090-3 and EN 1090-5; - the mechanical properties comply with the product standards listed in 5.2.2. (2) EN 1999 is intended to be used in conjunction with: - European Standards for construction products relevant for aluminium structures; - EN 1090-1, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components; - EN 1090-3, Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures; - EN 1090-5, Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications.

Eurocode 9 - Design of aluminium structures - Part 1-1: General rules

23/30457273 DC BS EN 1991-1-5 欧洲规范 1. 对结构的作用 第 1-5 部分 热作用

BS EN 1991-1-5. Eurocode 1. Actions on structures - Part 1-5. Thermal actions

23/30455838 DC BS EN 1991-1-3 欧洲规范 1. 对结构的作用 第 1-3 部分 雪荷载

BS EN 1991-1-3. Eurocode 1. Actions on structures - Part 1-3. Snow loads

23/30457255 DC BS EN 1991-1-9 欧洲规范 1. 对结构的作用 第 1-9 部分 一般动作 大气结冰

BS EN 1991-1-9. Eurocode 1. Actions on structures - Part 1-9. General actions. Atmospheric icing

T/CCIAT 0051-2023 超高泵送混凝土泵管清洗技术规程

本规程的主要技术内容是：1.总则；2.术语；3.基本规定；4.气洗施工；5.水洗施工；6.水气联洗施工；7.施工安全与环境保护。

Super high pumping concrete pump pipe cleaning technical regulations

DB64/T 1544-2023 绿色建筑设计标准

Green Building Design Standards

DB42/T 1948-2023 预拌混凝土标准化生产管理规程

Standardized production management procedures for ready-mixed concrete

CEN/TS 19101:2022 纤维聚合物复合结构的设计

1.1 Scope of FprCEN/TS 19101 (1) This document applies to the design of buildings, bridges and other civil engineering structures in fibre-polymer composite materials, including permanent and temporary structures. It complies with the principles and requirements for the safety, serviceability and durability of structures, the basis of their design and verification that are given in EN 1990. NOTE In this document, fibre-polymer composite materials are referred to as composite materials or as composites. (2) This document is only concerned with the requirements for resistance, serviceability, durability and fire resistance of composite structures. NOTE 1 Specific requirements concerning seismic design are not considered. NOTE 2 Other requirements, e.g. concerning thermal or acoustic insulation, are not considered. (3) This document gives a general basis for the design of composite structures composed of (i) composite members, or (ii) combinations of composite members and members of other materials (hybrid-composite structures), and (iii) the joints between these members. (4) This document applies to composite structures in which the values of material temperature in members, joints and components in service conditions are (i) higher than -40 °C and (ii) lower than - 20 °C, where is the glass transition temperature of composite, core and adhesive materials, defined according to 5.1(1). (5) This document applies to: (i) composite members, i.e. profiles and sandwich panels, and (ii) bolted, bonded and hybrid joints and their connections. NOTE 1 Profiles and sandwich panels can be applied in structural systems such as beams, columns, frames, trusses, slabs, plates and shells. NOTE 2 Sandwich panels include homogenous core and web-core panels. In web-core panels, the cells between webs can be filled (e.g. with foam) or remain empty (e.g. panels from pultruded profiles). NOTE 3 This document does not apply to sandwich panels made of metallic face sheets. NOTE 4 Built-up members can result from the assembly of two or more profiles, through bolting and/or adhesive bonding. NOTE 5 The main manufacturing processes of composite members include pultrusion, filament winding, hand layup, resin transfer moulding (RTM), resin infusion moulding (RIM), vacuum-assisted resin transfer moulding (VARTM). NOTE 6 This document does not apply to composite cables or special types of civil engineering works (e.g. pressure vessels, tanks or chemical storage containers). (6) This document applies to: (i) the composite components of composite members, i.e. composite plies, composite laminates, sandwich cores and plates or profiles, and (ii) the components of joints or their connections, i.e. connection plates or profiles (e.g. cleats), bolts, and adhesive layers. NOTE 1 Composite components are composed of composite materials (i.e. fibres and matrix resins) and core materials. Components of joints and their connections are also composed of composite, steel or adhesive materials. NOTE 2 The fibre architecture of composite components can comprise a single type of fibres or a hybrid of two or more types of fibres. NOTE 3 This document does not apply to composite components used for internal reinforcement of concrete structures (composite rebars) or strengthening of existing structures (composite rebars, strips or sheets). (7) This document applies to composite materials, comprising: (i) glass, carbon, basalt or aramid fibres, and (ii) a matrix based on unsaturated polyester, vinylester, epoxy or phenolic thermoset resins.

Design of fibre-polymer composite structures

EN 1993-1-1:2022 欧洲法规3:钢结构的设计.第1-1部分:一般规则和建筑物规则

1.1 Scope of FprEN 1993 1 1 (1) FprEN 1993 1 1 gives basic design rules for steel structures. (2) It also gives supplementary provisions for the structural design of steel buildings. These supplementary provisions are indicated by the letter "B" after the paragraph number, thus ( )B. 1.2 Assumptions (1) The assumptions of EN 1990 apply to FprEN 1993 1 1. (2) EN 1993 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), the parts of EN 1992 to EN 1999 where steel structures or steel components are referred to within those documents, EN 1090 2, EN 1090 4 and ENs, EADs and ETAs for construction products relevant to steel structures.

Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings

CEN/TS 1993-1-101:2022 欧洲规范 3：钢结构设计 第 1-101 部分：弯曲和压缩构件的替代相互作用方法

(1) This document provides an alternative method for the stability verification of steel members under compression axial force and bending moment, with reference to EN 1993 1 1. NOTE For the applicability of this document, see Clause 4. (2) The method given in this document applies to uniform steel members with double symmetric cross-section under axial compression force and bi-axial bending.

Eurocode 3: Design of steel structures - Part 1-101: Alternative interaction method for members in bending and compression