91.080.40 混凝土结构 标准查询与下载

T/ZS 0023-2018 装配式混凝土结构预制构件质量检验标准

前  言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  基本要求　 5  原材料检验　 5.1  一般要求　 5.2  混凝土　 5.3  钢筋与钢材　 5.4  保温材料与拉结件　 5.5  外装饰材料　 6  生产检验　 6.1  一般要求　 6.2  连接材料进厂（场）检验　 6.3  模具检验　 6.4  生产过程检验　 6.5  生产成品检验　 7  进场检验　 7.1  一般要求　 7.2  预制构件进场检验　 7.3  密封材料进场检验　 8  安装检验　

Quality inspection standard for prefabricated components of prefabricated concrete structures

ASTM C1602/C1602M-18 水硬性水泥混凝土生产用混合水的标准规范

1.1 This specification covers the compositional and performance requirements for water used as mixing water in hydraulic cement concrete. It defines sources of water and provides requirements and testing frequencies for qualifying individual or combined water sources. In any case where the requirements of the purchaser differ from these in this specification, the purchaser’s specification shall govern. 1.2 This specification does not purport to cover methods of storage, transportation, or blending of water, or to address the development and maintenance of quality control programs sponsored or managed by the manufacturer. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete

ASTM D4259-18 涂覆前用磨蚀制备混凝土的标准实施规程

1.1 This practice includes surface preparation of concrete to prepare the surface prior to the application of coatings. 1.2 This practice is intended to create a surface profile in concrete and to remove foreign materials and weak surface laitance. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Concrete by Abrasion Prior to Coating Application

SL 775-2018 水工混凝土结构耐久性评定规范

Specification for durability assessment of hydraulic concrete structures

DB42/T 1483-2018 装配整体式混凝土叠合剪力墙结构技术规程

Technical specification for assembled monolithic concrete laminated shear wall structure

ASTM D7635/D7635M-18 用于测量织物加强层涂层厚度的标准测试方法

1.1 This test method covers measuring the thickness of the coating over fiber backing or reinforcing fabric. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement

ASTM D4263-83(2018) 用塑料板法指示混凝土中水分的标准试验方法

1.1 This test method is used to indicate the presence of capillary moisture in concrete. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific caution statements, see Section 4. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method

ASTM D4262-05(2018) 化学清洗或蚀刻混凝土表面pH值的标准试验方法

1.1 This test method covers procedures for determining the acidity or alkalinity of concrete surfaces prepared by chemical cleaning or etching prior to coating. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for pH of Chemically Cleaned or Etched Concrete Surfaces

ASTM D4261-05(2018) 涂层用表面清洁混凝土砌块的标准实施规程

1.1 This practice covers surface cleaning of concrete masonry units to remove dust, dirt, mortar spatter, oil, and grease prior to the application of coatings. Procedures include vacuum cleaning, air-blast cleaning, water cleaning, detergent water wash, steam cleaning, and mechanical cleaning. 1.2 This practice may alter the surface profile of the concrete but is primarily intended to clean the surface. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Surface Cleaning Concrete Masonry Units for Coating

ASTM C1262/C1262M-18 评估干铸分段挡土墙单元和相关混凝土单元的冻融耐久性的标准试验方法

1.1 This test method covers the resistance to freezing and thawing of dry-cast segmental retaining wall (SRW) units (see Specification C1372) and related concrete units. Units are tested in a test solution that is either potable tap water or 3 % saline solution depending on the intended use of the units in actual service. NOTE 1—Related concrete units include units such as hollow and solid concrete masonry units, concrete brick, and concrete roof pavers. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this standard. Some values have only SI units because the inch-pound equivalents are not used in practice. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units

DB42/T 1345-2018 CRB600H高强钢筋应用技术规程

CRB600H high-strength steel bar application technical specification

ISO 18407:2018 预应力混凝土饮用水箱的简化设计

This document provides guidelines for the planning, design and construction of a cylindrical tank constructed on the ground with prestressed concrete (PC) for use with potable water tank. This document is applicable to PC tanks for potable water with a capacity of 30000 m3 or less and the diameter-to-height ratio (D/H) from 1,0 to 3,0. NOTE When designing and constructing a tank not covered by this document (reinforced concrete tanks, underground tanks, elevated tanks, etc.), a designer can refer to this document for common elements where possible.

Simplified design of prestressed concrete tanks for potable water

DB37/T 5106-2018 装配式混凝土结构现场检测技术标准

本标准适用于装配式混凝土结构的现场检测。

Technical standard for on-site inspection of prefabricated concrete structures

ASTM D5295/D5295M-18 粘结（粘结）膜防水系统混凝土表面制备标准指南

1.1 This guide provides recommendations for the preparation of concrete surfaces prior to the application of adhered (bonded) waterproofing. 1.2 This guide is directed primarily toward installations of new concrete, but is also applicable for existing concrete installations. (See also ACI 116 and ACI 546.) 1.3 This guide does not apply to loose laid systems, bentonite systems, lead, or the like. 1.4 This guide does not apply to applications involving insulating concrete. 1.5 This guide does not apply to applications involving lightweight structural concrete. NOTE 1—Once installed, it is difficult to visually identify the difference between normal weight and lightweight concrete. It is recommended that a review of contract documents, concrete batch or delivery tickets or similar effort be performed to identify the concrete type. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems

DB21/T 2225-2018 高性能混凝土应用技术规程

High Performance Concrete Application Technical Regulations

DB21/T 1559-2018 回弹法检测泵送混凝土抗压强度技术规程

Technical specification for testing the compressive strength of pumped concrete by rebound method

18/30331860 DC BS ISO 18408 混凝土 钢筋混凝土和预应力混凝土 钢筋混凝土墙体建筑简化结构设计导则

BS ISO 18408. Concrete. Reinforced concrete and pre-stressed concrete. Simplified structural design guidelines for reinforced concrete wall buildings

ASTM F2170-18 用原位探头测定混凝土楼板相对湿度的标准试验方法

Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes

T/UCST 001-2018 装配式混凝土结构工程施工安全技术标准

11111

Safety technical standard for construction of precast concrete structure engineering

NF A35-025:2017 钢筋混凝土用钢. 热浸镀锌钢筋和卷材

Steels for reinforced concrete - Hot dip galvanised bars and coils