91.080.40 混凝土结构 标准查询与下载

T/ZBTA 05-2020 装配式混凝土结构工程施工质量安全管理导则

本导则共分7章，主要技术内容包括：总则、术语、基本规定、建设单位、设计单位、施工单位、监理单位。

Guidelines for quality and safety management of precast concrete structures

DB21/T 2568-2020 装配式混凝土结构构件制作、施工与验收规程

Regulations for fabrication, construction and acceptance of prefabricated concrete structural components

ASTM C1583/C1583M-20 混凝土表面拉伸强度的标准试验方法和直接拉伸（拉拔法）混凝土修补和覆盖材料的粘结强度或拉伸强度

1.1 This test method is suitable for both field and laboratory use to determine one or more of the following: 1.1.1 The near-surface tensile strength of the substrate as an indicator of the adequacy of surface preparation before application of a repair or overlay material. 1.1.2 The bond strength of a repair or an overlay material to the substrate. 1.1.3 The tensile strength of a repair or overlay material, or an adhesive used in repairs, after the material has been applied to a surface. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)

ISO/TR 16475:2020 混凝土结构漏水裂缝修补通则

General practices for the repair of water-leakage cracks in concrete structures

DB37/T 5158-2020 地螺丝微型钢管桩技术规程

本规程适用于各种轻型建（构）筑物及小型市政、园林等工程地螺丝微型钢管桩的设计、施工、质量检查与验收。

Ground screw micro-steel pipe pile technical specification

ISO 14484:2020 使用纤维增强聚合物（FRP）材料的混凝土结构设计性能指南

This document provides general principles for the verification and assessment of the performance of concrete s tructures with the applications of different fibre-reinforced polymer (FRP) s ys tems varying from internal FRP reinforcements/tendons, external FRP tendons, externally bonded FRP sheets/ plates, to near-surface mounted FRP reinforcement. It can be used for the international harmonization of the design of un-reinforced, conventionally reinforced, and pre-stressed concrete s tructures with the use of the above-mentioned FRP s ystems.

Performance guidelines for design of concrete structures using fibre-reinforced polymer (FRP) materials

DB32/T 3754-2020 装配整体式混凝土结构检测技术规程

本规程适用于新建、改建、扩建和既有装配整体式混凝土结构的检测。

Technical specification for testing of assembled monolithic concrete structures

DB32/T 3755-2020 U型H型组合钢板桩支护技术规程

本规程适用于江苏省行政区域内一般地质条件下临时性支护结构设计、施工、管理。

U-shaped H-shaped combined steel sheet pile support technical specification

T/SCQA 206-2020 XC弹卡式连接预应力混凝土桩

本图集XC弹卡式连接预应力混凝土桩（简称弹卡式混凝土桩）是利用先张法工艺生产的采用弹卡式机械连接方式拼接的预应力混凝土预制桩。 本图集弹卡式混凝土桩包括弹卡式连接预应力混凝土管桩（简称弹卡式管桩）、弹卡式连接预应力混凝土空心方桩（简称弹卡式空心方桩）和弹卡式连接预应力混凝土实心方桩（简称弹卡式实心方桩）。其中弹卡式管桩和弹卡式空心方桩统称为弹卡式空心桩。 弹卡式混凝土桩上下节桩的连接方式构造简单，受力可靠直接，施工便捷。接桩面无钢制件外露，并利用专用环氧树脂封闭，形成一个可靠安全防腐节点，有效地保证整桩在地下复杂工况中可靠性和耐久性，显著地提高桩基工程质量。 本图集包含抗压桩和抗拔桩，均采用高强弹卡式连接接头。

XC clip type connection prestressed concrete pile

KS F 4015-2019 混凝土栅栏用预制钢筋构件的标准规范

Standard specifications for precast reinforced components for concrete fences

DB34/T 3469-2019 高延性混凝土应用技术规程

本规程适用于高延性混领土的原材料控制、性能要求、配合比设计、以及采用高延性混领土加固房屋建筑喝一般构筑物的砌体结构喝婚礼提构件设计、施工喝质量验收。其他行业的工程加固可参照使用。

High ductility concrete application technical specification

DB42/T 1534-2019 高强热轧带肋钢筋应用技术规程

Application technical specification for high-strength hot-rolled ribbed steel bars

DB32/T 3697-2019 既有建筑幕墙可靠性检验评估技术规程

本规程适用于江苏省既有建筑幕墙及与幕墙构造工法相似的采光顶等外围护结构的可靠性检验评估，金属屋面可参考执行。

Technical specification for reliability inspection and evaluation of existing building curtain walls

DB32/T 3696-2019 江苏省高性能混凝土应用技术规程

本规程适用于江苏省内设计使用年限为50年和100年的强度等级为C30~C80的结构混凝土。

Jiangsu High Performance Concrete Application Technical Regulations

DB32/T 3698-2019 建筑电气防火设计规程

本规程适用于除甲、乙类火灾危险性工业建筑以外的新建、扩建和改建的一般工业建筑和民用建筑的低压电气防火设计。

Code for Design of Building Electrical Fire Protection

T/CSUS 05-2019 大跨度预应力空心板建筑工程应用技术标准

1.0.1 为规范大跨度预应力空心板在建筑工程的设计、生产、施工及验收，做到安全适用、技术先进、经济合理、保证质量，制定本标准。 1.0.2 本标准适用于抗震设防烈度不大于8度的工业与民用建筑，环境类别为一类及二a类的预应力空心楼（屋面）板和建筑高度不大于24m的预应力空心外墙板的设计、生产、施工及验 收。本标准不适用于有振动作用以及有高温作用的建筑。 1.0.3 大跨度预应力空心板的设计、生产、施工及验收，除应符合本标准外，尚应符合国家现行有关标准的规定。 

Technical Standard for Building Engineering Application of Large-span Prestressed Hollow-core Slabs

T/CECS 188-2019 钢管混凝土叠合柱结构技术规程

本规程共分7章和1个附录，主要技术内容包括：总则、术语和符号、基本规定、叠合柱框架设计、钢管混凝土剪力墙设计、连接设计、结构施工及验收。 本规程修订的主要技术内容是： 1. 叠合柱结构的最大适用高度； 2.  采用实配法确定叠合柱框架柱端弯矩设计值及叠合柱、框架梁剪力设计值； 3. 叠合柱、钢管混凝土剪力墙最小抗剪截面验算时剪力设计值扣除钢管抗剪强度，受剪承载力计算时考虑钢管抗剪强度； 4.  偏心受压叠合柱正截面受压承载力计算方法； 5.  叠合柱轴压比计算方法； 6. 叠合柱箍筋加密区的箍筋配置； 7. 钢管混凝土剪力墙轴心受压承载力计算方法； 8. 偏心受压、偏心受拉钢管混凝土剪力墙斜截面受剪承载力计算方法； 9. 钢管混凝土剪力墙轴压比计算方法及轴压比限值； 10. 叠合柱、钢管混凝土剪力墙抗震构造措施； 11. 钢筋混凝土梁与叠合柱连接； 12. 叠合柱柱脚设计； 13.  叠合柱结构施工及验收。

Technical specification for steel tube-reinforced concrete column structures

T/CECS 648-2019 既有混凝土框架结构隔震加固技术规程

本规程共分7章和2个附录，主要技术内容包括：总则、术语、设计、施工、分项工程验收、子分部工程验收和维护等。

Technical specification for strengthening with seismic isolation of existing concrete frame structures

ASTM C1542/C1542M-19 混凝土芯长度的标准试验方法

1.1 This test method is used to determine the length of a core drilled from concrete. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Length of Concrete Cores

ASTM D7234-19 使用便携式拉脱附着力测试仪的混凝土涂层的拉脱粘合强度的标准测试方法

Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers