91.080.40 混凝土结构 标准查询与下载
共找到 1068 条与 混凝土结构 相关的标准，共 72 页
Technical specification for shield starting and receiving cut glass fiber reinforced concrete enclosure structure
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2017-12-14
- 实施
- 2018-04-01
Technical specification for single-row reinforced concrete shear wall structure of multi-storey buildings
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2017-12-14
- 实施
- 2018-04-01
This part of EN 1504 gives requirements for - substrate condition before and during application of systems and products; - storage of systems and products; - structural stability during preparation, protection and repair; - methods of protection and repair; - quality control for execution of work; - maintenance of the structure. These aspects include effects on health and safety, the working environment, the environment and the economy.
Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 10: Site application of products and systems and quality control of the works; German version EN 150
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2017-12-01
- 实施
本标准规定了冲击回波法检测混凝土缺陷的检测程序和检测判定方法。 本标准适用于冲击回波法对混凝土厚度、缺陷的检测与判定，测试范围为 200～1500 mm。
Technical specification for detection of concrete defects by impact echo method
- ICS
- 91.080.40
- CCS
- P 25
- 发布
- 2017-11-15
- 实施
- 2017-12-15
Products and systems for the protection and repair of concrete structures - Definitions@ requirements@ quality control and evaluation of conformity - Part 10: Site application of products and systems and quality control of the works
- ICS
- 91.080.40
- CCS
- 发布
- 2017-10-01
- 实施
Guidelines for Design and Maintenance of Concrete Bridge Structural Health Monitoring System
- ICS
- 91.080.40
- CCS
- P 25
- 发布
- 2017-09-06
- 实施
- 2017-10-06
1.1 This practice covers surface preparation of concrete to prepare the surface prior to the application of coatings. 1.2 This practice is intended to alter the surface profile of the concrete and to remove foreign materials and weak surface laitance. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Liquid and Gelled Acid Etching of Concrete
- ICS
- 91.080.40
- CCS
- 发布
- 2017-09-01
- 实施
1.1 This practice includes surface cleaning of concrete to remove grease, dirt, and loose material prior to the application of coatings. Procedures include broom cleaning, vacuum cleaning, air blast cleaning, water cleaning, detergent water cleaning, and steam cleaning. 1.2 This practice is not intended to alter the surface profile of the concrete but to clean the surface. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Surface Cleaning Concrete for Coating
- ICS
- 91.080.40
- CCS
- 发布
- 2017-09-01
- 实施
Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
- ICS
- 91.080.40
- CCS
- 发布
- 2017-09-01
- 实施
Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
- ICS
- 91.080.40
- CCS
- 发布
- 2017-09-01
- 实施
This standard applies to the design and construction of brick floors.
Design of concrete structures - Part 100: Brick floors
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2017-09-00
- 实施
This Standard gives requirements and provisions for the conformity assessment of brick floors in accordance with DIN 1045-100.
Design of concrete structures - Part 101: Evaluation of Conformity for brick floors in accordance with DIN 1045-100
- ICS
- 91.080.40
- CCS
- 发布
- 2017-09-00
- 实施
1总则；2术语；3基本规定；4钻切设计；5金刚石薄壁钻切割法施工；6金刚石圆盘锯切割法施工；7金刚石绳锯切割法施工；8 质量检验。
Technical specification for drilling and cutting of existing concrete structures
- ICS
- 91.080.40
- CCS
- E470
- 发布
- 2017-06-19
- 实施
- 2017-06-20
1.1 This practice is for the evaluation of coatings used in below grade applications to resist the passage of water through concrete block. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Resistance to Hydrostatic Pressure for Coatings Used in Below Grade Applications Applied to Masonry
- ICS
- 91.080.40
- CCS
- 发布
- 2017-06-01
- 实施
本标准规定了以混凝土为基材的机械锚栓的分类和标记、要求、试验方法、检验规则、标志、产品说明书、包装、运输及贮存。 本标准适用于抗压强度25 MPa~60 MPa的开裂或者非开裂混凝土上锚固的金属锚栓。
Mechanical anchors for use in concrete
- ICS
- 91.080.40
- CCS
- P32
- 发布
- 2017-05-27
- 实施
- 2017-12-01
Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 1: Test method for thermal stability
- ICS
- 91.080.40
- CCS
- 发布
- 2017-05
- 实施
Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing; German version EN 1766:2017
- ICS
- 91.080.40
- CCS
- P25
- 发布
- 2017-05
- 实施
Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 6: Test method for response to the substrate movement
- ICS
- 91.080.40
- CCS
- 发布
- 2017-05
- 实施
Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 5: Test method for watertightness
- ICS
- 91.080.40
- CCS
- 发布
- 2017-05
- 实施
Green Concrete Technical Regulations
- ICS
- 91.080.40
- CCS
- Q 13
- 发布
- 2017-02-23
- 实施
- 2017-03-23
