91.120.20 建筑物声学、隔音 标准查询与下载

KS F 2864-2022 参考其他声学参数测量房间的混响时间

Measurement of the reverberation time of rooms with reference to the other acoustical parameters

KS F ISO 717-2-2022 声学.建筑物和建筑构件的隔音等级.第2部分:冲击隔音

Acoustics — Rating of sound insulation in buildings and of building elements — Part 2: Impact sound insulation

ASTM E1042-22 镘刀抹涂或喷涂吸音材料的分类

1.1 This classification covers materials applied by trowel or spray to surfaces for the purpose of increasing their acoustical absorption. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification for Acoustically Absorptive Materials Applied by Trowel or Spray

KS F ISO 717-2:2022 声学.建筑物和建筑构件的隔音等级.第2部分:冲击隔音

Acoustics — Rating of sound insulation in buildings and of building elements — Part 2: Impact sound insulation

ASTM E1573-22 使用A加权和三分之一倍频程声压级测量和报告掩蔽声级的标准试验方法

1.1 This test method specifies the procedure used to measure the masking sound in terms of A-weighted and one-thirdoctave-band sound pressure levels. 1.2 The results of this test method can be used to determine if and where the masking sound meets (or does not meet) a particular specification. 1.3 This test method does not evaluate the overall acoustical environment. It is intended only to measure and report the masking sound levels. 1.4 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement and Reporting of Masking Sound Levels Using A-Weighted and One-Third-Octave-Band Sound Pressure Levels

ASTM C635/C635M-22 隔音砖和铺设面板天花板用金属悬挂系统的制造、性能和试验标准规范

1.1 This specification covers metal ceiling suspension systems used primarily to support acoustical tile or acoustical lay-in panels. 1.2 Some suspension systems incorporate locking assembly details that enhance performance by providing some continuity or load transfer capability between adjacent sections of the ceiling grid. The test methods of Test Methods E3090/E3090M referenced in this specification do not provide the means for making a complete evaluation of continuous beam systems, nor for assessing the continuity contribution to overall system performance. However, the test methods can be used for evaluating primary structural members in conjunction with secondary members that interlock, as well as with those of noninterlocking type. 1.3 While this specification is applicable to the exterior installation of metal suspension systems, the atmospheric conditions and wind loading require additional design attention to ensure safe implementation. For that reason, a specific review and approval should be solicited from the responsible architect and engineer, or both, for any exterior application of metal suspension systems in the construction of a new building or building modification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Manufacture, Performance, and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings

ASTM C367/C367M-22 预制建筑隔音砖或铺设天花板强度特性的标准试验方法

1.1 These test methods cover the determination of the strength properties of prefabricated architectural acoustical tile or lay-in ceiling panels as follows: Tests Sections Hardness 4 to 9 Friability 10 to 16 Sag 17 to 23 Transverse strength 24 to 30 1.2 Not all of the tests described in these test methods are necessary to evaluate any particular product for a specific use. In each instance, it is necessary to determine which properties are required. 1.3 These test methods specify procedures that are used in product development, manufacturing control, specification acceptance, and service evaluation. 1.4 Properties determined by these test methods reflect the performance of the materials under the specific conditions of the test, and do not necessarily indicate performance under conditions other than those specified herein. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems will result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Strength Properties of Prefabricated Architectural Acoustical Tile or Lay-In Ceiling Panels

T/CSUS 40-2022 装配式建筑室内声环境技术标准

1.0.1  为全面改善装配式建筑室内声环境质量，不断提升我国装配式建筑建设水平，减少装配式建筑受噪声影响，营造健康、舒适的室内建筑声环境，制定本标准。 1.0.2  本标准适用于采用装配式结构体系与集成化内装工艺建造的住宅建筑、公共建筑及工业建筑。本标准中未提及的其他类型装配式建筑，依据其建筑结构形式及使用功能，可参照本标准的相应规定。 1.0.3  本标准对各类型装配式部品部件的隔声评价标准所采用的测量方法和隔声性能等级按现行国家隔声测量标准执行。 1.0.4  装配式建筑中各类型的部品部件除应符合本标准的规定外，还应符合国家现行有关标准的规定。

Technical Standard for indoor acoustic environment of prefabricated buildings

ASTM E3090/E3090M-22 金属天花板悬挂系统强度性能的标准试验方法

1.1 These test methods cover metal ceiling suspension systems used primarily to support acoustical tile, acoustical lay-in panels, or suspended T-bar type ceiling systems. 1.2 These test methods cover the determination of strength properties of suspended ceiling grid system components as follows: Tests Subsections Load Carrying Capacity 5.1 Connection Strength in Tension 5.2.2; 5.2.4 Connection Strength in Compression 5.2.3; 5.2.5 Wire Pullout Resistance 5.3 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Strength Properties of Metal Ceiling Suspension Systems

ASTM E413-22 隔声等级分类

1.1 This classification covers methods of calculating singlenumber acoustical ratings for laboratory and field measurements of sound attenuation obtained in one-third octave bands. 1.2 The name given to the single-number rating is assigned by the test method that invokes this classification. 1.3 Test methods that invoke this classification include: 1.3.1 Test Method E90—The single-number rating is called sound transmission class (STC). 1.3.2 Test Method E336—Single number ratings are noise isolation class (NIC), normalized noise isolation class (NNIC), and apparent sound transmission class (ASTC). 1.3.3 Test Method E596—The single-number rating is called noise isolation class (NIC). 1.3.4 Test Method E1414—The single-number rating is called ceiling attenuation class (CAC). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Classification for Rating Sound Insulation

ISO 23591:2021/AWI Amd 1:2022 音乐排练室和空间的声学质量标准 修正案 1

Acoustic quality criteria for music rehearsal rooms and spaces — Amendment 1

BS EN ISO 3382-3:2022 声学 房间声学参数的测量 开放式办公室

What is ISO 3382-3 - Room acoustic parameters of open-plan offices about?    An open-plan office is a large and open office space where a large number of occupants can simultaneously work in well-defined workstations. ISO 3382-3 specifies a method for the measurement of room acoustic parameters in unoccupied open-plan offices. ISO 3382-3   specifies measurement procedures, the apparatus needed, the coverage required, the method for evaluating the data, and the presentation of the test report.   ISO 3382-3 describes a group of single-number quantities indicating the room acoustic performance of an open-plan office in a condition when one person is speaking. They focus on spatial decay of speech while the quantities in ISO 3382-2 focus on temporal decay of sound.   Who is ISO 3382-3 - Room acoustic parameters of open-plan offices for?     ISO 3382-3 on

Acoustics. Measurement of room acoustic parameters. Open plan offices

22/30443554 DC BS EN 12354-5 建筑声学 根据元件性能估算建筑物的声学性能 第 5 部分：服务设备产生的声级

BS EN 12354-5. Building acoustics. Estimation of acoustic performance of building from the performance of elements - Part 5. Sounds levels due to the service equipment

ASTM C423-22 混响室法测定吸声和吸声系数的标准试验方法

1.1 This test method covers the measurement of sound absorption in a reverberation room by measuring decay rate. Procedures for measuring the absorption of a room, the absorption of an object, such as an office screen, and the sound absorption coefficients of a specimen of sound absorptive material, such as acoustical ceiling tile, are described. 1.2 Field Measurements—Although this test method covers laboratory measurements, the test method described in 4.1 can be used for making field measurements of the absorption of rooms (see also 5.5). A method to measure the absorption of rooms in the field is described in Test Method E2235. 1.3 This test method includes information on laboratory accreditation (see Annex A1), asymmetrical screens (see Annex A2), and reverberation room qualification (see Annex A3). 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method

T/GDJSKB 008-2022 建筑楼板用隔声砂浆

前 言 1 范围 2 规范性引用文件 3 术语和定义 4 标记 4.1 标记方法 4.2 标记示例 5 原材料 5.1 橡胶颗粒 5.2 水泥 5.3 细骨料 5.4 矿物掺和料 5.5 拌合水 5.6 胶粘剂 6 要求 6.1 干混料外观 6.2 干混料堆积密度 6.3 干混料放射性 6.4 隔声砂浆分层度 6.5 撞击声隔声性能 6.6 基本性能（10mm 硬化隔声层） 6.7 燃烧性能 7 试验方法 7.1 干混料外观 7.2 干混料堆积密度 7.3 干混料放射性 7.4 隔声砂浆分层度 7.5 撞击声隔声性能 7.6 基本性能（10mm 硬化隔声层）  7.7 燃烧性能级别 8 检验规则 8.1 检验类别与项目 8.2 出厂检验 8.3 型式检验 9 产品标志及随行文件 9.1 产品标志 9.2 产品随行文件 10 包装、运输和贮存 10.1 包装 10.2 运输 10.3 贮存

Sound insulation mortar for building floor

EN ISO 3382-3:2022 声听学.室内声学参数的测量.开放式办公室

This document specifies a method for the measurement of room acoustic parameters in unoccupied open-plan offices. It specifies measurement procedures, the apparatus needed, the coverage required, the method for evaluating the data, and the presentation of the test report. This document describes a group of single-number quantities indicating the room acoustic performance of an open-plan office in a condition when one person is speaking. They focus on spatial decay of speech while the quantities in ISO 3382-2 focus on temporal decay of sound.

Acoustics - Measurement of room acoustic parameters - Part 3: Open plan offices (ISO 3382-3:2022)

ISO 3382-3:2022 声学.房间声学参数的测量.第3部分:开放式办公室

This document specifies a method for the measurement of room acoustic parameters in unoccupied open-plan offices. It specifies measurement procedures, the apparatus needed, the coverage required, the method for evaluating the data, and the presentation of the test report. This document describes a group of single-number quantities indicating the room acoustic performance of an open-plan office in a condition when one person is speaking. They focus on spatial decay of speech while the quantities in ISO 3382-2 focus on temporal decay of sound.

Acoustics — Measurement of room acoustic parameters — Part 3: Open plan offices

T/SHMHZQ 134-2021 矩阵消声器技术规范

4 型号命名  5 技术要求  6 试验方法 7 检验规则  8 标志、包装、运输和贮存

Technical specification for matrix mufflers

KS F 2871-2021 公寓浴室排水噪声的标准试验方法

Standard test method of drainage noise in apartment bathroom

KS F 2870-2021 公寓浴室供水噪声的标准试验方法

Standard test method of water supply noise in apartment bathroom