共找到 462 条与 防水 相关的标准,共 31 页
Standard coating method of liquid-applied waterproofing membrane
1、产品按粘贴饰面材料种类分为I型和II型: I型适用于工程防水及天然饰面砖的粘贴,II型适用于工程防水及天然饰面石材的粘贴。 2、产品呈干粉状、均匀、无结块。 3、物理力学性能应符合以下表的规定 项 目 技 术 要 求 Ⅰ型 Ⅱ型 凝结时间 初凝/min ≥ 180 终凝/min ≤ 660 抗折强度/MPa(28d) ≥ 4.0 抗压强度/MPa(28d) ≥ 12.0 柔韧性(横向变形)/mm ≥ 1.0 涂层抗渗压力/MPa(7d) ≥ 0.5 拉伸粘结强度a/MPa(28d) ≥ 1.0 1.0 浸水后拉伸粘结强度a/MPa(28d) ≥ 1.0 1.0 热老化后拉伸粘结强度a/MPa(28d) ≥ 1.0 1.0 晾置时间20min拉伸粘结强度a/MPa(28d) ≥ 0.5 1.0 收缩率/% ≤ 0.30
Polymer-modified cementitious mixtures
Technical Regulations for Building Waterproof Engineering
一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存等
Waterborne polyurethane waterproof paint
1.外观::A组分搅拌后均匀无色差、无凝胶、无结块,无明显沥青丝。B组分无结块,溶于水后能形成均一稳定的液体。2.A组分固体含量:本标准产品的固体含量主要针对A组分的橡胶沥青乳液,其B组分通常状态固体包装,使用时溶解在水中,因此固体含量仅针对A组分。作为水性涂料,固体含量越高运输成本越低,但考虑到生产工艺的可行性及成本,固体含量应控制在一个合适的水平,验证试验结果在(55~60)%,指标定为55%;3.凝胶时间:作为速凝材料,还需要考虑其凝胶时间,便于在异型和立面施工,降低对表面平整度的要求,需要注意的是
Sprayed quick setting rubber asphalt waterproof coating
Examination method for Hanok — Part 1: Comfort
Examination method for Hanok — Part 2: Environmental properties
Examination method for Hanok — Part 2: Environmental properties
Examination method for Hanok — Part 1: Comfort
Waterproofing of tanks and pools - Part 3: Waterproofing with liquid-applied waterproofing materials
Waterproofing of tanks and pools - Part 1: Requirements and principles for design and execution
Waterproofing for indoor applications - Part 2: Waterproofing with waterproofing materials in sheet form
Waterproofing for indoor applications - Part 3: Waterproofing with liquid-applied waterproofing materials in conjunction with tiles and paving
Waterproofing for indoor applications - Part 4: Waterproofing with mastic asphalt or asphalt mastic
Waterproofing of tanks and pools - Part 2: Waterproofing with waterproofing materials in sheet form
Waterproofing of elements in contact with soil - Part 1: Requirements and principles for design and execution
Waterproofing of elements in contact with soil - Part 3: Waterproofing with liquid-applied waterproofing materials
Waterproofing of buildings - Supplement 2: Information on methods for the determination of thickness of liquid-applied waterproofing materials and evaluation of the results
Waterproofing for indoor applications - Part 1: Requirements and principles for design and execution
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号