91.120.30 防水 标准查询与下载

KS F 4925-2018 水泥砂浆混合流动性止水剂

Cement mortar mixed liquid waterproofing agent

KS F 4938-2018 对于以防水 阻根材料的根系穿透阻力绿色屋顶系统试验方法

Standard test method for root penetration resistance

T/SGFS 004-2018 非固化橡胶沥青防水涂料

非固化橡胶沥青防水涂料的分类、原材料、技术要求、试验方法、检验规则、标志、包装、贮存与运输

Non-curing rubber bitumen waterproof coating

T/SGFS 003-2018 高分子自粘胶膜防水卷材

高分子自粘胶膜防水卷材的分类、原材料、技术要求、试验方法、检验规则、标志、包装、贮存与运输

Polymer Self Adhesive Film Waterproof Membrane

CSA Z800-2018 地下室防洪和降低风险指南

1 Domaine d’application 1.1 Généralités Ces lignes directrices donnent des mesures pour réduire les risques d’inondation du sous-sol et pour atténuer les effets négatifs sur les biens, la sécurité publique et la santé publique en cas d’inondation. Elle traite des maisons existantes, neuves, reconstruites et rénovées dans les contextes ruraux et urbains. 1.2 Bâtiments concernés Ces lignes directrices concernent tous les types de maisons touchant le sol, avec ou sans sous-sol, qui sont considérées des bâtiments selon la Partie 9 du Code national du bâtiment (CNB), notamment : a) maisons isolées; b) maisons jumelées; et c) maisons en rangée. Les recommandations données dans ces lignes directrices sont généralement appropriées pour les maisons desservies par un réseau à écoulement gravitaire pluvial, sanitaire, unitaire ou une canalisation de drainage. 1.3 Types de risque d’inondation Les types de risque d’inondation concernés par les mesures décrites dans ces lignes directrices sont : a) les inondations terrestres associées à des précipitations et résultant en une accumulation/ formation d’étang et/ou de la fonte de la neige dans des maisons touchant au sol ou autour de celles-ci; b) le refoulement d’égout sanitaire et pluvial (surcharge); c) l’inondation par infiltration (infiltration des eaux souterraines); d) défaillance de la tuyauterie et du drainage, incluant la défaillance des systèmes de puisard et du branchement d’égout; et e) l’inondation associée à une mauvaise installation des technologies de réduction des risques d’inondation du sous-sol (voir l’annexe A). Note : Il est rappelé aux utilisateurs de ces lignes directrices que toute disposition donnée dans les présentes est l’objet de codes et normes existants applicables dans la compétence en vertu de laquelle l’utilisateur des lignes directrices exerce ses activités. Il est fortement recommandé que des professionnels certifiés appropriés effectuent tout travail indiqué dans ces lignes directrices. Tous les codes et toutes les normes locaux, provinciaux et nationaux appropriés doivent être respectés lors de l’application des dispositions indiquées aux présentes. Tous les permis et toutes les inspections appropriés des autorités compétentes doivent être obtenus et effectués lors de la mise en oeuvre de toute tâche précitée.

Guidelines for Basement Flood Protection and Risk Reduction

T/ZZB 0781-2018 高分子自粘胶膜防水卷材

本标准规定了高分子自粘胶膜防水卷材的规格与标记、基本要求、技术要求、试验方法、检验规则、标志、包装、贮存与运输、质量承诺。 本标准适用于以塑料（P）为主体材料，一面有自粘胶，胶表面采用不粘或减粘材料处理，与后浇混凝土粘结的防水卷材。

Self adhered polymer waterproofing membrane

T/SCDA 018-2018 PTS防水涂料系统建筑构造

T-100 断裂伸长率 ≥500%，T-100 粘结强度≥1.0Mpa，T-100 不透水性 0.3Mpa，120min不透水 T-200H 断裂延伸率≥400%

PTS Waterproof Coating System Building Construction

ASTM E2359/E2359M-13(2018) 现场外部绝缘和表面处理系统包层壁组件的现场拉伸测试的标准测试方法

1.1 This test method covers a procedure to determine the resistance of a section of the exterior insulation and finish system (EIFS) to outward loads imposed on an existing exterior wall assembly that has been in place on the building for an unspecified period of time. It is destructive in nature within the localized areas tested and requires appropriate repair of the EIFS cladding and sheathing once the test procedure has been completed. This test procedure utilizes mechanical methods to obtain information, which may be helpful in evaluating the natural application of negative wind loads on the EIFS assembly. Some variability of results should be anticipated within the wall assembly tested due to differences in installation procedures, exposure, or abuse subsequent to application. 1.2 This test method is suitable for use on cladding assemblies that have been in place a short time (new construction), as well as for longer periods in order to evaluate detrimental effects on the EIFS lamina, insulation attachment, substrate integrity, and attachments after exposure to weather and other environmental conditions. It is not intended to evaluate the performance of structural framing. Test results on any particular building may be highly variable depending on specimen location and condition, and are subject to interpretation by the test specifier. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard may involve hazardous materials, operations, or equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. NOTE 1—Due to variations in exposure and construction assemblies, field specimens selected for testing utilizing this test method may experience sudden failure and release of the imposed loads. See Note 7 for further information. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Field Pull Testing of an In-Place Exterior Insulation and Finish System Clad Wall Assembly

ASTM E2485/E2485M-13(2018) 外部绝缘和表面处理系统（EIFS）和防水屏障涂层的冷冻/抗冻性的标准测试方法

1.1 This test method covers procedures for determining the effect of freezing and thawing of exterior insulation and finish systems (EIFS), an EIFS with water-resistive barrier coatings, and water-resistive barrier coatings by itself. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Freeze/Thaw Resistance of Exterior Insulation and Finish Systems (EIFS) and Water Resistive Barrier Coatings

DB42/T 1386-2018 建筑防水工程技术规范

Technical specification for building waterproof engineering

JC/T 2470-2018 彩石金属瓦

本标准规定了彩石金属瓦的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于工业和民用建筑屋面的彩石金属瓦。

Stone coated cetal roofing tile

JC/T 2435-2018 单组分聚脲防水涂料

本标准规定了单组分聚脲防水涂料的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于建设工程防水用单组分聚脲防水涂料。

Mono-component liquid applied polyurea waterproofing coating

ASTM E1643-18a 用于接触混凝土板下土或颗粒填料的水蒸气缓凝剂的选择 设计 安装和检查的标准操作规程

1.1 This practice covers procedures for selecting, designing, installing, and inspecting flexible, prefabricated sheet membranes in contact with earth or granular fill used as vapor retarders under concrete slabs. 1.2 Conditions subject to frost and either heave or hydrostatic pressure, or both, are beyond the scope of this practice. Vapor retarders are not intended to provide a waterproofing function. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs

ASTM E1643-18 用于接触混凝土板下土或颗粒填料的水蒸气缓凝剂的选择 设计 安装和检查的标准操作规程

Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs

BS 8533:2017 评估和管理开发中的洪水风险 实践守则

Assessing and managing flood risk in development. Code of practice

KS F 4931-2017 桥梁混凝土桥面防水卷材

Waterproofing sheets for concrete deck of bridge

KS F 4932-2017 桥梁混凝土桥面防水卷材涂料

Waterproofing membrane coating for concrete deck of bridge

T/SGFS 002-2017 改性沥青柔性防水卷材

改性沥青柔性防水卷材的分类、原材料、技术要求、试验方法、检验规则、标志、包装、贮存与运输

Modified asphalt flexible waterproof membrane

JC/T 2428-2017 非固化橡胶沥青防水涂料

本标准规定了非固化橡胶沥青防水涂料(以下简称非固化防水涂料)的术语和定义、标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于建设工程非外露防水用的非固化橡胶沥青防水涂料。

Non-curable rubber modified asphalt coating for waterproofing

KS F 9003-2017 液体防水卷材的标准涂装方法

Standard coating method of liquid-applied waterproofing membrane