91.120.30 防水 标准查询与下载

T/CASMES 65-2022 防水卷材用玻璃纤维毡

本文件规定了防水卷材用玻璃纤维毡的要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于防水卷材用玻璃纤维毡。

Glass fiber mat for waterproofing rolls

T/CBMF 189-2022 装配式防水板

本文件规定了装配式防水板的分类和标记、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本文件适用于外防内贴法施工的隧道或地下防水工程用装配式防水板。

Prefabricated waterproof board

T/CBMF 188-2022 装配式防水板

本文件规定了装配式防水板的分类和标记、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本文件适用于外防内贴法施工的隧道或地下防水工程用装配式防水板。

Prefabricated waterproof board

T/CWA 208-2022 高性能聚合物改性沥青防水卷材

1　范围 2　规范性引用文件 3　术语和定义 4　分类和标记 5　一般要求 6　要求 7   试验方法 8   检验规则 9   标志、包装、贮存与运输

High-performance polymer modified bitumen sheet

T/CWA 209-2022 无溶剂聚氨酯防水涂料

1、产品按组分分为：单组分(S)、双组分(M)。 2、产品按使用部位分为：平面用(H)、立面用(V)。 3、产品物理力学性能应符合以下规定：              项目                                  指标          固体含量/%                          ≥99.0          表干时间/h                           ≤12          实干时间/h                           ≤24        流平性（H类）   　  20 min时，无明显齿痕        抗流挂性（V类）　 湿膜厚度600μm时，不流挂       撕裂强度/(N/mm)　             ≥15           低温弯折性/℃　        -35 ℃，无裂纹           加热伸缩率/％　        -2.0～＋1.0 4、产品的有害物质限量应符合以下规定：                  项目                                                         技术指标      挥发性有机物含量(VOC)/(g/L)　                            ≤20              苯/(mg/kg)　                                                    ≤20        甲苯+乙苯+二甲苯/(g/kg)　                                    ≤1.0              苯酚/(mg/kg)　                                            ≤100              蒽/(mg/kg)　                                                    ≤10              萘/(mg/kg)　                                                    ≤200              游离TDI/(g/kg)　                                           ＜0.1 4,4’-二氨基-3,3’-二氯二苯甲烷(MOCA)/(g/kg)　   ＜0.1       短链氯化石蜡含量(C10～C13)/(g/kg)　                   ＜0.1          总铅Pb/(mg/kg)　                                            ≤90           　                                 镉Cd　                    ≤10        可溶性重金属/(mg/kg)        铬Cr　                    ≤20 　                                         汞Hg　                    ≤10       总挥发性有机化合物TVOC释放量/(mg/m3)　            ≤1.0

Solvent-free polyurethane waterproof coating

T/HBBWA CJFS01-2022 建筑防水系统构造图集（一）

《建筑防水系统构造图集（一）（建筑防水排蓄一体化系统）》（T/HBBWA CJFS01-2022）介绍了河北强凌防水材料集团有限公司生产的SBS改性沥青防水卷材、玄武岩MBH预铺防水卷材、玄武岩MBH耐根穿刺防水卷材、玄武岩CNH外露型防水卷材、环境友好型单组份聚氨酣防水涂料、聚合物水泥防水涂料、非固化橡胶沥青防水涂料、喷涂速凝橡胶沥青防水涂料、 HDPE塑料防护排水板等产品在建筑屋面、地下、有水房间、 水池及其他工程中的防水构造做法和应用技术。

Construction Atlas of Building Waterproof System (1)

ASTM E2266-22 抗水入侵的低层框架建筑墙体系统的设计和建造的标准指南

1.1 This guide describes design, specification, selection, installation, and inspection of new building wall systems, exterior deck and stair components, doors, windows, penetrations and sealant joints of wood and metal frame buildings, typically four stories or less, to minimize water intrusion. 1.2 This guide does not address prevention of damage caused by water originating from the use of wet building materials or from indoor or outdoor humidity. Water from these sources can be important, and the potential for damage caused by water from these sources must not be overlooked in building design or construction. 1.3 This guide does not address roofing systems, except when the surface of a deck also serves as a roof and at locations where roof systems interface with building walls. 1.4 This guide does not address any type of barrier wall system. 1.5 This guide does not address any exterior insulation and finish system (EIFS). 1.6 This guide does not address foundation conditions where the bottom of a slab on grade or the grade of a crawl space is at or below the water table or subject to hydrostatic pressure. 1.7 This guide is intended to supplement and not duplicate building code requirements. 1.8 Maintenance, although important, is not covered in detail. 1.9 Application of finishes, such as paint and sealers, may be important in the performance of some types of cladding; however, this is not covered in detail. 1.10 This guide applies only to constructions with sheathing, which facilitates installation of the water-resistive barrier and associated flashings in a common plane. 1.11 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.12 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.13 Organization of Document: Section Scope 1 Referenced Documents 2 Terminology 3 Summary of Guide 4 Significance and Use 5 General Design Principles 6 Design Practices 7 General Guidelines 8 Drainage Walls 9 Drainage Walls—General 9.1 Drainage Wall Cladding—Portland Cement Plaster (Stucco) 9.2 Drainage Wall Cladding—Wood and Wood-Derived Products 9.3 Drainage Wall Cladding—Vinyl Siding 9.4 Drainage Wall Cladding—Fiber-Cement Siding 9.5 Cavity Drainage Walls 10 Cavity Drainage Walls—General 10.1 Cavity Drainage Wall Cladding—Masonry 10.2 Wood Framed Decks and Stairs with Exposed Framing and Decking 11 Plaza Decks or Stairs with Enclosed Framing and a Waterproofing Membrane with Separate Wearing Surfaces 12 Plaza Decks or Stairs with Enclosed Framing and a Waterproofing Membrane with an Integral Wearing Surface 13 Windows, Doors, and Similar Wall Penetrations 14 Special Wall Configuration 15 Exterior Sealant Joints 16 Keywords 17 Appendix—Introduction to Guide Details Appendix X1 Appendix—General Notes for Cement Plaster (Stucco) Details Appendix X2 Appendix—Additional Resources Appendix X3 1 This guide is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.55 on Performance of Building Enclosures. Current edition approved May 15, 2022. Published May 2022. Originally approved in 2004. Last previous edition approved in 2021 as E2266–21. DOI: 10.1520/E2266-22. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.14 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion

GSO ASTM E241:2022 限制水引起的建筑物损坏的标准指南

1.1 This guide covers building design, construction, commissioning, operation, and maintenance. 1.2 This guide addresses the need for systematic evaluation of factors that can result in moisture-induced damage to a building or its components. Although of great potential importance, serviceability issues which are often, but not necessarily, related to physical damage of the building or its components (for example, indoor air quality or electrical safety) are not directly addressed in this guide. 1.3 The emphasis of this guide is on low-rise buildings. Portions of this guide; in particular Sections 5, 6, and 7; may also be applicable to high-rise buildings. 1.4 This guide is not intended for direct use in codes and specifications. It does not attempt to prescribe acceptable limits of damage. Buildings intended for different uses may have different service life expectancies, and expected service lives of different components within a given building often differ. Furthermore, some building owners may be satisfied with substantially shorter service life expectancies of building components or of the entire building than other building owners. Lastly, the level of damage that renders a component unserviceable may vary with the type of component, the degree to which failure of the component is critical (for example, whether failure constitutes a life-safety hazard), and the judgement (that is, tolerance for damage) of the building owner. For the reasons stated in this paragraph, prescribing limits of damage would require listing many pages of exceptions and qualifiers and is beyond the scope of this guide.

Standard Guide for Limiting Water-Induced Damage to Buildings

ASTM C1471/C1471M-22 在垂直表面上使用高固体含量冷液体应用弹性防水膜的标准指南

1.1 This guide describes the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the performance criteria specified in Specification C836/ C836M, subject to intermittent hydrostatic pressure in a waterproofing system intended for installation on vertical cast-in-place concrete surfaces. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces

T/CSUS 41-2022 新型聚氨酯喷涂防水工程技术规程

1.0.1  为规范新型单组份聚氨酯防水材料（以下简称单组份聚氨酯防水材料或本材料）在工程中的应用，做到技术领先、质量可靠、经济适用、安全环保，制定本技术规程。 1.0.2  本规程依据现行国家标准《地下工程防水技术规范》GB50108、《屋面工程质量验收规范》GB50207等的原则制定。 1.0.3  单组份聚氨酯防水材料适用于建筑结构、轨道交通结构、地下结构、城市综合管廊等新建、改扩建、维修中的防水设计、施工及验收。 1.0.4  单组份聚氨酯防水材料在工程项目中的设计、施工及质量验收，除应符合本规程标准，尚应符合国家现行有关标准。

Specification for the engineering techniques of a new type spay-applicable polyurethane waterproofing material

BS 8102:2022 保护地下结构免遭进水 实践守则

What is BS 8102 – Code of practice for below ground structures about? BS 8102 focuses on below ground structures. BS 8102 provides best industrial guidance for design of below ground structures to prevent contamination. BS 8102 gives recommendations and provides guidance on methods of dealing with and preventing the entry of water from external sources into structures that are partly or wholly below ground. It covers the use of: Waterproofing barrier materials applied to the structure Structurally integral watertight construction Drain...

Protection of below ground structures against water ingress. Code of practice

T/JCMS 0004-2022 高强度橡胶复合纤维防水卷材

本文件规定了高强度橡胶复合纤维防水卷材的编码、要求、试验方法、检验规则和标志、包装、运输和贮存。 本文件适用于以高强度基布为胎基，添加天然橡胶和合成橡胶，在上、下表面复合土工布，经压延、硫化而制成的高强度橡胶复合纤维防水卷材。主要用于人防、铁路路基、铁路桥梁、隧道、工业和民用建筑等场所的防水工程。

High strength rubber composite fiber waterproof sheet

T/CECS 1025-2022 建筑工程复合防水技术规程

主要内容包括：总则、术语、基本规定、材料、设计、施工、验收。

Composite Waterproof Technical Regulations for Construction Engineering

T/CECS 1004-2022 刚性防水工程技术规程

主要技术内容包括：总则、术语、基本规定、材料、设计、施工、质量检查与验收、维护。

Rigid Waterproof Engineering Technical Regulations

T/CECS 989-2022 建筑室内渗漏修缮技术规程

主要技术内容包括：总则、术语、基本规定、查勘、设计与施工、质量验收。

Technical specification for indoor leakage repair of buildings

T/NAIC 006-2021 近零能耗建筑用产品评价 防水透汽、防水隔汽材料

本文件规定了近零能耗建筑用防水透汽材料、防水隔汽材料评价的术语和定义、一般要求、评价要求和评价方法。 本文件适用于近零能耗建筑用防水透汽膜（墙面、屋面用）、防水透汽膜（门窗洞口用）等防水透汽材料，及防水隔汽膜（屋面、室内、地基用）、防水隔汽膜（门窗洞口用）等防水隔汽材料产品评价。

Evaluation of products for near-zero-energy buildings Waterproof and vapor-permeable and waterproof and vapor-insulating materials

T/CWA 207-2021 水性聚氨酯防水涂料

1、产品按是否暴露使用分为外露型（E）和非外露型（N）。 2、产品为均匀粘稠体，无凝胶、无分层、结块现象。 3、产品的物理力学性能应符合下表的规定：                         项  目　                          技术指标         低温断裂伸长率/%　-10℃　            ≥450         撕裂强度/（N/mm）　                    ≥15         低温弯折性/℃　                             -35℃，无裂纹         燃烧性能a　                                            B2-E 4、产品的有害物质含量应符合下表的规定：                             项  目　                                     技术指标         挥发性有机物含量（VOC）/（g/L）            　≤30         苯+甲苯+乙苯+二甲苯/（mg/kg）                  ≤20         甲醛含量/（mg/kg）　                                ≤50         氨/（mg/kg）　                                                ≤300         可溶性重金属 /（mg/kg）　铅Pb　        ≤20 　                                                镉Cd　        ≤20 　                                                铬Cr　                ≤20 　                                                汞Hg　        ≤20

Waterborne polyurethane waterproof coating

T/ZZXJX 109-2021 建筑外墙防水工程技术规程

前  言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本规定　 5 防水材料　   5.1 一般规定　   5.2 防水涂料　   5.3 刚性防水材料　   5.4 密封材料　   5.5 其他材料　 6 防水设计　   6.1 一般规定　   6.2 外墙找平层设计　   6.3 外墙防水层设计　   6.4 外墙饰面层设计　   6.5 外墙窗户防水设计　   6.6 外墙细部构造防水设计　   6.7 墙体防潮设计　 7 防水施工　   7.1 一般规定　   7.2 无外保温外墙防水工程施工　   7.3 外保温外墙防水工程施工　 8 工程验收　   8.1 一般规定　   8.2 砂浆防水层　   8.3 涂膜防水层　   8.4 防水透气膜防水层　   8.5 密封防水　

Technical specifications for waterproofing engineering of building exterior walls

T/ZZXJX 095-2021 屋面防水工程技术规程

前  言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本规定　 5 防水材料　   5.1 一般规定　   5.2 防水卷材　   5.3 防水涂料　   5.4 刚性防水材料　   5.5 密封材料　   5.6 其他材料　 6 防水设计　   6.1 一般规定　   6.2 屋面排水　   6.3 防水基层　   6.4 找坡层和找平层　   6.5 保温层　   6.6 屋面排汽构造　   6.7 隔汽层　   6.8 防水层　   6.9 种植屋面防水　   6.10 坡屋面防水　   6.11 单层防水卷材屋面防水　   6.12 细部构造防水　 7 防水施工　   7.1 一般规定　   7.2 平屋面防水施工　   7.3 坡屋面防水施工　 8 工程验收　   8.1 一般规定　   8.2 卷材防水层　   8.3 涂膜防水层　   8.4 复合防水层　   8.5 接缝密封防水　   8.6 檐沟和天沟　   8.7 女儿墙和山墙　   8.8 变形缝　

Roof waterproof engineering technical regulations

T/ZZXJX 093-2021 地下防水工程技术规程

前  言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 基本规定　 5 防水材料　   5.1 一般规定　   5.2 防水卷材　   5.3 防水涂料　   5.4 刚性防水材料　   5.5 密封材料　   5.6 其他材料　 6 防水设计　   6.1 一般规定　   6.2 结构构件自防　   6.3 柔性防水层　   6.4 聚合物水泥防水砂浆层　   6.5 地下工程种植土顶板　   6.6 地下工程背水面　   6.7 地下防水工程细部节点构造　 7 防水施工　   7.1 一般规定　   7.2 疏排水层　   7.3 盲沟排水   7.4 桩头防水　   7.5 变形缝防水　   7.6 穿墙螺栓防水　   7.7 穿墙管（盒）防水　   7.8 施工缝防水施工　   7.9 地下工程柔性防水层　 8 工程验收　   8.1 一般规定　   8.2 防水混凝土　   8.3 水泥砂浆防水层　   8.4 卷材防水层　   8.5 涂料防水层　   8.6 施工缝　   8.7 变形缝　   8.8 后浇带　   8.9 穿墙管　   8.10 预留通道接头　   8.11 桩头　

Technical Regulations for Underground Waterproofing Engineering