91.140.10 中央供热系统 标准查询与下载
共找到 883 条与 中央供热系统 相关的标准，共 59 页
This European Standard applies to the thermal output testing of fan assisted radiators, convectors and trench convectors which are factory assembled or kits, i.e. - fan assisted radiators and convectors, provided the heater has a dedicated fan or fans; - trench convectors with and without fan(s), provided the heater and the fan(s) are dedicated; - ventilation radiators and convectors.
Fan assisted radiators@ convectors and trench convectors - Part 2: Test method and rating for thermal output
- ICS
- 91.140.10
- CCS
- J96
- 发布
- 2014-12
- 实施
This European Standard defines the technical specifications and requirements of radiators and convectors to be installed in heating systems in buildings including assessment and verification of constancy of performance. This European Standard deals with radiators and convectors installed in a permanent manner in construction works, fed with water or steam at temperatures below 120 °C, supplied by a remote energy source. This European Standard does not apply to independent heating appliances. This European Standard also defines the additional common data that the manufacturer shall provide with the product in order to ensure the correct application of the products.
Radiators and convectors - Part 1: Technical specifications and requirements
- ICS
- 91.140.10
- CCS
- J96
- 发布
- 2014-12
- 实施
This European Standard defines procedures for determining the standard thermal outputs and other characteristics of radiators and convectors installed in a permanent manner in construction works, fed with water or steam at temperatures below 120 °C, supplied by a remote energy source. This European Standard specifies the laboratory arrangements and testing methods to be adopted, the admissible tolerances, the criteria for selecting the samples to be tested and for verifying the conformity of the current production with the samples tested at the initial test. This European Standard also defines the additional common data that the manufacturer shall provide with the product in order to ensure the correct application of the products. This European Standard does not apply to fan assisted radiators, fan assisted convectors and trench convectors and to independent heating appliances.
Radiators and convectors - Part 2: Test methods and rating
- ICS
- 91.140.10
- CCS
- J96
- 发布
- 2014-12
- 实施
This European Standard defines the technical specifications and requirements of fan assisted radiators, convectors and trench convectors for permanent installation in central heating systems which are factory assembled or kits. This European Standard covers fan assisted radiators and convectors fed with water at temperatures below 120 °C, supplied by a remote heating source. This European Standard also applies for radiators and convectors according to EN 442-1 to determine their dry cooling capacity. This European Standard does not apply to discrete heating appliances. This European Standard also defines the additional common data that the manufacturer is to provide to the trade in order to ensure the correct application of the products. This European Standard applies to the testing for the determination of thermal output and dry cooling capacity of - fan assisted radiators and convectors, provided the heater/cooler has a dedicated fan or fans; - trench convectors with and without fan(s), provided the fan(s) are dedicated; - ventilation radiators and convectors (only heating); - not fan assisted radiators and convectors (only cooling).
Fan assisted radiators@ convectors and trench convectors - Part 1: Technical specifications and requirements
- ICS
- 91.140.10
- CCS
- J96
- 发布
- 2014-12
- 实施
本规范适用于应用于工作压力≤1.0MPa，设计温度≤85℃的 PE-RT Ⅱ型低温直埋供热管道系统的设计与施工。
Specifications for the design and construction of type Ⅱ heat-resistant polyethylene (PE-RTⅡ) low-temperature direct-buried heating pipelines
- ICS
- 91.140.10
- CCS
- P45
- 发布
- 2014-09-16
- 实施
- 2014-11-01
Heating systems in buildings - Design for water-based heating systems; German version EN 12828:2012+A1:2014
- ICS
- 91.140.10
- CCS
- Q83
- 发布
- 2014-07-01
- 实施
This standard deals with the exhaust-side corrosion of metallic materials in directly heated hot-water systems in hot-water heating systems and the associated exhaust systems. The application of this standard helps to minimise the probability of component failure or malfunction through proper planning, design and operation. This standard is intended for use by manufacturers, planners, erectors and installation operators. Corrosion at high temperatures, such as oxide scaling, is not covered by this standard.
Prevention of damage in water heating installations - Corrosion by fuel gases
- ICS
- 91.140.10
- CCS
- 发布
- 2014-07
- 实施
This British Standard specifies requirements for the selection, installation, inspection, commissioning, servicing and maintenance of gas-fired boilers for central heating and other purposes, which have a total rated heat input not exceeding 70 kW based on net calorific value. This includes cookers with integral boilers used to provide central heating.
Specification for selection, installation, inspection, commissioning, servicing and maintenance of gas-fired boilers of rated input not exceeding 70 kW net
- ICS
- 91.140.10
- CCS
- J98
- 发布
- 2014-05-31
- 实施
- 2014-05-31
Heating systems in buildings - Design for water-based heating systems (Incorporates Amendment A1: 2014)
- ICS
- 91.140.10
- CCS
- P46
- 发布
- 2014-04-01
- 实施
This European Standard specifies design criteria for water based heating systems in buildings with a maximum operating temperature of up to 105 °C. In case of heating systems with maximum operating temperatures over 105 °C other safety aspects than those described in 4.6 may apply. The other clauses of this European Standard are still valid for those systems. This European Standard does not amend product standards or product installation requirements. This standard covers the design of:- heat supply systems; - heat distribution systems; - heat emission systems; - control systems. This European Standard takes into account heating requirements of attached systems (e. g. domestic hot water, process heat, air conditioning, ventilation) in the design of a heat supply, but does not cover the design of these systems. This European Standard does not cover requirements for installation or commissioning or instructions for operation, maintenance and use of water based heating systems. This European Standard does not cover the design of fuel and energy supply systems.
Heating systems in buildings - Design for water-based heating systems
- ICS
- 91.140.10
- CCS
- 发布
- 2014-04
- 实施
本规程适用于新建、扩建和改建的工业与民用建筑中，以发热电缆为加热元件的地面低温辐射供暖系统的设计、选材、施工、调试与验收等。
Technical specification for ground low-temperature radiant heating with heating cables
- ICS
- 91.140.10
- CCS
- P45
- 发布
- 2014-01-02
- 实施
- 2014-03-01
Gas-fired central heating boilers. Type C boilers of nominal heat input exceeding 70 kW, but not exceeding 1000 Kw. Classification, requirements, test methods and marking
- ICS
- 91.140.10
- CCS
- J98
- 发布
- 2014
- 实施
- 2016-01-01
Gas-fired central heating boilers. Part 1. Technical requirements and test methods
- ICS
- 91.140.10
- CCS
- J98
- 发布
- 2014
- 实施
- 2016-01-01
Inset appliances including open fires fired by solid fuels. Requirements and test methods
- ICS
- 91.140.10
- CCS
- Y68
- 发布
- 2014
- 实施
- 2016-01-01
Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW. Terminology, requirements, test methods and marking
- ICS
- 91.140.10
- CCS
- J98
- 发布
- 2014
- 实施
- 2016-01-01
Domestic heating boilers fired by solid fuel nominal heat output up to 50 kW. Requirements and test methods
- ICS
- 91.140.10
- CCS
- J98
- 发布
- 2014
- 实施
- 2016-01-01
Heat cost allocators for the determination of the consumption of room heating radiators - Appliances with electrical energy supply; German version EN 834:2013
- ICS
- 91.140.10
- CCS
- P46
- 发布
- 2013-12
- 实施
Heating systems in buildings. Design for water-based heating systems
- ICS
- 91.140.10
- CCS
- Q76
- 发布
- 2013-11-30
- 实施
- 2013-11-30
Das Dokument enthalt einen Korrekturhinweis.*www.vdi.de/2077
Energy consumption accounting for the building services - Determination of reimbursable costs of heat generation by CHP systems - Corrigendum concerning guideline VDI 2077 Blatt 3.1:2012-11
- ICS
- 91.140.10
- CCS
- 发布
- 2013-10
- 实施
NOTE See Clause 3 for a definition of the terms used below. This European standard applies to heat cost allocators which are used to capture the proportionate thermal output of radiators in consumer units. If an account unit comprises consumer units of di
Heat cost allocators for the determination of the consumption of room heating radiators - Appliances with electrical energy supply
- ICS
- 91.140.10
- CCS
- 发布
- 2013-09-19
- 实施
- 2013-09-19
