91.140.10 中央供热系统 标准查询与下载

CSA/ANSI Z21.47:21 • CSA 2.3-2021 燃气中央炉

1 Scope 1.1 This Standard applies to automatically operating gas-fired central furnaces (see Clause 3), hereinafter referred to as furnaces, for installation in residential, commercial, and industrial structures including furnaces for direct vent, recreational vehicle, outdoor, and manufactured (mobile) homes. These furnaces can include a cooling unit. All units are to be constructed entirely of new, unused parts and materials. 1.2 In Canada, this Standard applies to gas-fired central furnaces having inputs up to and including 400 000 Btu/h (117 228 W). 1.3 This Standard applies to Category I, Category II, Category III, and Category IV central furnaces. See Clause 3. 1.4 This Standard applies to furnaces of the types defined in Clause 3, which are designed to supply heated air through ducts to spaces remote from or adjacent to the furnace location. Location and use of such furnaces with respect to the spaces being heated necessitates automatic operation of the appliance. 1.5 This Standard covers the thermal efficiency (see Clause 5.40) and related markings of only those furnaces whose efficiencies are not regulated in the U.S.A. by the Energy Policy Act and Conservation Act of 1975 and the National Energy Conservation Policy of 1978* or not covered in Canada by Clause 13 when connected to a single phase electrical supply. Note: * At the time of printing, Federal energy acts in the U.S.A. regulate the efficiency (heating capacity) of furnaces having input ratings less than 225 000 Btu/h (65 941 W). 1.6 A furnace of a type not specifically defined in this Standard may be subjected to such examination and tests as deemed necessary by the testing agency to determine compliance with the intent of this Standard. 1.7 This Standard also applies to a furnace that is factory equipped with both a draft hood and an automatic vent damper device (see Clause 3), hereinafter referred to as vent damper device. 1.8 If a value for measurement as given in this Standard is followed by an equivalent value in other units, the first stated value is regarded as the specification, except as noted in Clauses 4.22.1 and 4.26.2. 1.9 All references to “psi” throughout this Standard are considered gauge pressures, unless otherwise specified. 1.10 Special construction provisions applicable to a furnace designed for use with an optional listed conversion kit are outlined under Annex H. 1.11 Clause 2 contains a list of standards specifically referenced in this Standard. Clause 2 includes both U.S. and Canadian reference standards where applicable. It is the responsibility of the user of this Standard to determine which referenced standard applies based on the requirements of the authority having jurisdiction at the location of the installation. However, a furnace for use in a particular country only should comply with the applicable referenced standard for that country. 1.12 Clause 4.17 is unique to United States. The Canadian electrical equipment and wiring provisions are contained in CSA C22.2 No. 3 or CAN/CSA-C22.2 No. 60335-2-102. 1.13 Special construction provisions applicable to furnaces designed to operate at altitudes over 2000 ft (610 m) are outlined in Annex K. 1.14 In this Standard, “shall” is used to express a requirement, i.e. a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Gas-fired central furnaces

T/HBJC 004-2021 直埋供热用II型耐热聚乙烯管

本文件规定了直埋供热用II型耐热聚乙烯管的术语、定义、符号和缩略语、一般规定、要求、试验方法、检验规则、标志、运输和贮存。 本文件适用于直径不大于450mm直埋供热用II型耐热聚乙烯管制造和检验。   

Type II heat-resistant polyethylene pipes for direct buried heating

EN 1264-4:2021 地板加热.系统和组件.第4部分:安装

Water based surface embedded heating and cooling systems - Part 4: Installation

EN 1264-3:2021 地板加热.系统和组件.第3部分:标示尺寸

Water based surface embedded heating and cooling systems - Part 3: Dimensioning

EN 1264-5:2021 内部水基表面加热和冷却系统.第5部分:地板,天花板和墙内部加热和冷却表面.热输出的测定

Water based surface embedded heating and cooling systems - Part 5: Determination of the thermal output for wall and ceiling heating and for floor, wall and ceiling cooling

DS/EN 303-5:2021 加热锅炉 第5部分：手动和自动加燃料的固体燃料加热锅炉，额定热输出高达 500 kW 术语、要求、测试和标记

Heating boilers – Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW – Terminology, requirements, testing and marking

EN 303-5:2021 供暖锅炉.第5部分:用固体燃料,手动和自动填料燃烧,额定热功率300kW以下的采暖锅炉.术语,要求,检验和标识

Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking

EN 12831-3:2017/prA1:2021 建筑物的能源性能 设计热负荷的计算方法 第3部分：生活热水系统热负荷和需求表征，模块 M8-2、M8-3

Energy performance of buildings - Method for calculation of the design heat load - Part 3: Domestic hot water systems heat load and characterisation of needs, Module M8-2, M8-3

OENORM B 8311-2021 家庭供热系统安装施工

Installation and construction of domestic heat generating systems

DB21/T 3384-2021 空气源热泵系统工程技术规程

Air source heat pump system engineering technical regulations

GOST R 59501-2021 内部建筑物和构筑物公用设施 加热系统的安装和调整 工程执行和控制规则

Internal buildings and structures utilities. Mounting and adjusting of heating systems. Rules of carrying out and control of performance of works

DB23/T 2771-2020 黑龙江省城镇供热经营服务标准

Heilongjiang Province Urban Heating Operation Service Standards

T/BJWSA 0005-2020 供热保障专业应急救援队伍建设规范

本文件规定了供热保障专业应急救援队伍建设基本要求以及基础设施建设、组织机构及人员配备、 装备物资配备和队伍管理要求。 本文件适用于供热保障专业应急救援队伍建设。

Specifications for the construction of professional emergency rescue teams for heating protection

T/ZZB 1730-2020 采暖用分集水器

本标准规定了地暖系统中应用的采暖用分集水器（简称分集水器）产品的术语和定义、结构、尺寸与标记、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本标准适用于在民用与工业建筑工程中地暖水系统中（水温范围5 ℃～95 ℃）使用的工作压力不大于0.8 MPa、连接管径不大于DN32的采暖用分集水器。

Distribution manifold for heating

DB34/T 3599-2020 民用住宅供热计量温控一体化系统技术规范

Technical specification for residential heating metering and temperature control integrated system

DB37/T 3799-2019 城镇冬季供热服务规范

Specifications for urban heating services in winter

DB37/T 3798-2019 城镇燃气行业服务规范

Town gas industry service specification

KS B 6403-2019 散热器疏水阀

Radiator traps

KS B 6405-2019 散热器阀门和配件

Valves and fitting for radiator

BS EN 215:2019 散热器恒温阀 要求及测试方法

What is BS EN 215 - Thermostatic radiator valves about?    BS EN 215 discusses thermostatic radiator valves. BS EN 215 specifies definitions, requirements and test methods for thermostatic radiator valves referred to hereafter as thermostatic valves.   BS EN 215 applies to two-port thermostatic valves with or without pre-setting facility and thermostatic integrated valves with or without the pre-setting facility for fitting to radiators in wet central heating installations up to a water temperature of 120 °C and a nominal pressure of PN 10.   BS EN 215 further specifies the dimensions, the materials, and the connection details of four series of straight and angle pattern thermostatic radiator valves of nominal pressure ≤ PN 10. BS EN 215 can be used as a reference in a CEN/CENELEC Certification Mark System on thermostatic radiator valves.   Who is BS EN 215 -

Thermostatic radiator valves. Requirements and test methods