91.140.80 排水系统 标准查询与下载

BS EN 1253-2:2015 建筑物集水沟 试验方法

Gullies for buildings. Roof drains and floor gullies without trap

BS EN 1253-1:2015 建筑物雨水口 要求

Gullies for buildings. Trapped floor gullies with a depth water seal of at least 50 mm

CAN/CSA-S503-2015 北方社区的社区排水系统规划、设计与维护

1 Scope and application 1.1 Scope This Standard specifies provisions for the planning, design, and maintenance of surface drainage systems within northern community boundaries. Provisions for drainage outside the community boundary are not covered by this Standard. Note: Specific resources and expertise are required to address drainage provisions outside the community boundary. These resources and expertise might be beyond the capacity of an individual community. 1.2 Application This Standard specifies provisions for site-level and community-wide drainage system planning, development, and operations. The provisions apply to drainage systems used for the collection, conveyance, detention, and discharge of excess surface water in the form of overland flow, originating from precipitation, snowmelt, or ice melt. Note: Excess surface water is net of precipitation, soil infiltration, and evaporation. 1.3 Exclusions This Standard does not cover a) drainage systems associated with facilities that might inherently produce contaminated drainage, such as i) solid waste management systems and components; and ii) sewage treatment systems and components; b) drainage directly from storm surges in lakes or oceans; c) drainage directly from riverine flooding; d) subsurface drainage; and e) watershed level drainage planning. Note: Certain drainage circumstances are not considered in this Standard because they have requirements that are beyond the resources and expertise of many northern communities. 1.4 Terminology In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate normative clauses from explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Community drainage system planning, design, and maintenance in northern communities

EN 1253-1:2015 建筑沟.第 1部分：至少50毫米深的水密封困楼沟

This European Standard classifies floor gullies for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a depth of water seal of at least 50 mm (further: floor gullies). Although normally used to convey domestic wastewater, these floor gullies may convey other wastewater, e. g. industrial wastewater, provided there is no risk of damage to components or of injury to health. This European Standard does not apply to:- linear drainage channels as specified in EN 1433; - gully tops and manhole tops which are specified in EN 124; - roof drains and floor gullies without trap as specified in EN 1253-2.

Gullies for buildings - Part 1: Trapped floor gullies with a depth water seal of at least 50 mm

EN 1253-2:2015 建筑沟.第 2部分：屋顶排水沟和无陷阱楼沟

This European Standard classifies roof drains and floor gullies without trap for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking as well as test methods of factory made roof drains and floor gullies without trap (further: floor gullies) for buildings, irrespective of the material for use in drainage systems. Although normally used to convey rainwater and wastewater, these roof drains and floor gullies without trap may convey other wastewater provided there is no risk of damage to components or of injury to health. This European Standard does not apply to trapped floor gullies with a depth of water seal of at least 50 mm as specified in EN 1253-1.

Gullies for buildings - Part 2: Roof drains and floor gullies without trap

GOST R 56779-2015 饮用水热水供应分配系统. 能耗和有效性的计算方法

Systems of distribution of potable water hot-supply. Computational method of energy consumption and effectiveness

GOST R 56776-2015 消费热水供应的准备系统. 能源消耗和有效性的计算方法

The systems of preparation of consumer hot water-supply. Computational method of energy consumption and effectiveness

PD CEN/TR 13801:2014 建筑物内废水和污水排放(低温和高温)用塑料管道系统.热塑性塑料.安装的操作规程建议

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation

DB11/ 1071-2014 排水管（渠）工程施工质量检验标准

Drainage pipe (canal) engineering construction quality inspection standard

DB21/T 2241-2014 城市雨水利用系统技术规程

Technical specification for urban rainwater utilization system

CJ/T 431-2013 排水用螺纹钢管

本标准规定了排水用螺纹钢管(以下简称管材)的术语和定义,材料,结构、分类和连接,要求,试验方法,检验规则,标志、运输和贮存。本标准适用于输送介质温度在45℃以下无压埋地城镇排水、工业排水等工程使用的覆塑螺纹钢管以及城镇雨水排放和收集、农田输水等工程使用的镀锌螺纹钢管。

Helical corrugated steel pipe for drains

DB21/T 2122-2013 复合结构塑料排水检查井

Composite structure plastic drainage inspection well

CJ/T 178-2013 建筑排水柔性接口承插式铸铁管及管件

本标准规定了建筑排水柔性抗震接口铸铁管材及管件的型号、管材及管件、配套件、要求、试验方法、检验规则、标志和质量证明书、包装、运输和贮存等。 本标准适用于建筑排水柔性抗震接口铸铁管及管件。

Fauceting cast iron pipes and fittings with flexible joint for building drainage

DB11/T 967-2013 塑料排水检查井应用技术规程

Application technical specification for plastic drainage inspection well

DB13/T 1692-2012 滨海区暗管排水排盐技术规程

本规范规定了滨海盐碱区暗管排水排盐技术所涉及的术语和定义、适用条件与技术要求。本规范适用于河北省滨海盐碱区采用暗管排水排盐技术进行盐碱低产田改良或者盐碱荒地开发的系统工程。

Technical regulations for drainage and salt discharge of underground pipes in coastal areas

ANSI/ASSE 1030-2013 生活污水排泄系统用正压降低设备的性能要求

Performance Requirements for Positive Pressure Reduction Devices for Sanitary Drainage Systems

ANSI/NSF 46(i22r2)-2013 污水处理用组件和设备的评估

Evaluation of components and devices used in wastewater treatment systems

ANSI/ASSE 1056-2013 泄漏耐真空断路器装配的性能要求

Performance Requirements for Spill Resistant Vacuum Breaker Assemblies

ANSI/ASCE/EWRI 12/13/14-2013 城市地下排水系统设计用ASCE/EWRI 12-05标准指南;城市地下排水系统安装用ASCE/EWRI 13-05标准指南;及近五年内带有材料开发的城市地下排水系统操作和维护用ASCE/EWRI 14-05标准指南

ASCE/EWRI 12-05 Standard Guidelines for the Design of Urban Subsurface Drainage; ASCE/EWRI 13-05 Standard Guidelines for the Installation of Urban Subsurface Drainage; and ASCE/EWRI 14-05 Standard Guidelines for the Operation and Maintenance of Urban Subs

ANSI/NSF 40(i26r3)-2013 住宅污水处理系统

Residential Wastewater Treatment Systems