93.040 桥梁建筑 标准查询与下载

T/YJB 0039-2022 转体法桥梁施工技术规程

目次 1 总则 2 术语 3 基本规定 3.1 一般规定 3.2 跨越既有道路  3.3 跨越河道  3.4 跨越既有铁路 4 转动系统施工 4.1 一般规定 4.2 下转盘施工 4.3 球铰施工 4.4 上转盘施工 5 转体 5.1 一般规定 5.2 称重与配重 5.3 试转 5.4 转体及姿态调整 5.5 转体监控 6 合龙 6.1 一般规定 6.2 支架法合龙 6.3 挂篮法合龙 6.4 吊架法合龙

Technical Specification for Bridge Construction of Swivel Method

DB53/T 1113-2022 预应力混凝土连续刚构桥梁施工监控技术规程

Technical regulations for construction monitoring of prestressed concrete continuous rigid frame bridges

GSO ASTM D4014:2022 桥梁用滑动轴承和钢层弹性轴承的标准规范

This specification covers bearings, which consist of all elastomer or of alternate laminates of elastomer and steel, when the function of the bearings is to transfer loads or accommodate relative movement between a bridge superstructure and its supporting structure, or both. The bearings are furnished in four types as follows: plain elastomeric bearing pad; plain elastomeric sandwich bearing; steel-laminated elastomeric bearing; and steel-laminated elastomeric bearing with external load plate. The elastomer for the manufacture of the bearing is furnished in two types: Type CR and Type NR. The elastomer for the manufacture of the bearing is furnished in four grades of low-temperature properties: Grade 0; Grade 2; Grade 3; and Grade 5. The elastomeric compound used in the construction of a bearing shall contain only either natural rubber or chloroprene rubber as the raw polymer. Internal steel laminates shall be of rolled mild steel. Plain bearing pads shall be molded individually, or cut from previously molded strips or slabs, or extruded and cut to length. A steel-laminated bearing or a plain sandwich bearing shall be molded as a single unit under pressure and heat. All bonding of elastomer to steel laminates and to external load plates shall be carried out during molding. Bearing compression tests, compression stiffness, visual inspection, quality control properties, shear modulus, ozone resistance, and low-temperature grade tests shall be performed to conform to the specified requirements.

Standard Specification for Plain and Steel-Laminated Elastomeric Bearings for Bridges

T/JSJTQX 26-2022 冲击弹性波法预应力孔道压浆密实度检测技术规程

《冲击弹性波法预应力孔道压浆密实度检测技术规程》技术内容介绍 后张法预应力孔道压浆施工是保证预应力结构质量的重要工序。近年来，管道压浆质量缺陷较普遍，作为隐蔽工程，孔道压浆质量控制难度大，缺乏相应检查手段，压浆密实度只能通过破坏性检查评判，费时费工。冲击弹性波法是近年兴起的无损检测技术。本文件通过对冲击弹性波法测试原理、检测方式和数据解析方法等实践研究，编制了冲击弹性波法密实度检测的技术标准，给出了冲击弹性波法压浆密实度检测操作要点，采用定性检测和定量检测结果判定标准，为公路桥梁预应力孔道压浆质量检验提供了理论依据。

Technical specification for testing compactness of prestressed duct grouting by impact elastic wave method

T/CHTS 10053-2022 港珠澳大桥施工技术指南 第四分册：墩身、承台预制与安装

总则、术语、墩身/承台预制厂、墩身/承台构件预制与出运、钢套箱围堰墩台安装、钢圆筒围堰墩台安装、预制墩身拼接工程、施工监测

Technical Guideline for Construction of Hong Kong-Zhuhai-Macao Bridge DivisionⅣ: Prefabrication and Installation of Pier and Cap

ASTM D4788-03(2022) 用红外热成像法检测桥面分层的标准试验方法

1.1 This test method covers the determination of delaminations in portland-cement concrete bridge decks using infrared thermography. This test method is intended for use on exposed and overlaid concrete bridge decks. 1.2 A Precision and Bias statement has not been developed at this time. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes. NOTE 1—This test method can be used on asphalt or concrete overlays as thick as 4 in. (100 mm). 1.3 This test method uses an imaging infrared scanner and video recorder, mounted on a vehicle, to detect delaminations and debonded areas on bridge decks and to record the information. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Detecting Delaminations in Bridge Decks Using Infrared Thermography

DB34/T 3703.4-2022 长大桥梁养护指南 第4部分：健康监测系统数据库架构设计标准

Maintenance Guide for Long Bridges Part 4: Design Standards for Database Architecture of Health Monitoring System

DB34/T 4097-2022 农村公路桥梁设计与施工实施指南

Guidelines for Design and Construction of Rural Highway Bridges

DB34/T 4096-2022 公路混凝土斜拉桥锚拉板技术指南

Technical Guidelines for Anchor-stayed Plates of Highway Concrete Cable-Stayed Bridges

DB34/T 3703.5-2022 长大桥梁养护指南 第5部分：健康监测报警阈值设定

Maintenance Guide for Long Bridges Part 5: Alarm Threshold Setting for Health Monitoring

T/HQPA 8-2022 金属复合阻尼器

《金属复合阻尼器》的主要技术内容包括：范围、规范性引用文件、术语、定义和符号、品分类、型号、结构形式及规格、技术要求、检验规则、标志、包装、储存、运输。

Metal Composite Damper

T/HQPA 7-2022 建筑隔震双阶滑移滑板支座

本文件的主要技术内容包括：支座的设计要求，性能要求以及橡胶材料、滑移材料、滑移面板、橡胶滑块、支座组装及支座防尘防腐方面的要求。

Building seismic isolation double-stage sliding slide bearing

DB41/T 2244-2022 夹克法桩基加固设计施工技术规程

Technical specification for design and construction of pile foundation reinforcement by jacket method

T/JSJTQX 25-2022 桥梁减振降噪曲线型伸缩装置

    本标准规定了公路桥梁曲线降噪伸缩装置定义、结构型号、技术要求以及试验检验项目及方法，对关键技术指标降噪性能及测试方法进了明确，同时推荐了安装工艺。本团准是对我国现行公路桥梁伸缩装置标准体系模数式（直线型）、梳齿板式（折线型）以及无缝式（整体平面型）而无曲线型装置的有益补充。

Surface vibration reduction and noise reduction expansion device

T/CECS G D60-11-2022 公路装配式钢筋混凝土箱涵设计施工技术规程

本规程分为9章、2篇附录，主要内容包括：总则、术语和符号、基本规定、材料、结构设计、构造要求、构件预制、现场施工、质量检验，附录A箱涵构件的常压蒸汽养生、附录B预制构件保护层的测量。

Technical Specification for Design and Construction of Highway Prefabricated Reinforced Concrete Box Culverts

T/CECS G:D45-01-2022 公路纤维混凝土桥面铺装技术规程

本规程分为7章，主要内容包括总则，术语，设计要求，材料，配合比，施工，质量管理与检查验收，附录A目标配合比计算—正交试验法，附录B目标配合比计算—经验公式法，附录C施工配合比计算。

Technical Specifications for Fiber Reinforced Concrete Bridge Deck Pavement

DB44/T 2353-2022 大节段钢箱梁施工监控技术规范

Technical specification for construction monitoring of large section steel box girder

DB44/T 2360-2022 城际铁路设计细则

Intercity Railway Design Rules

T/CHTS 10049-2022 港珠澳大桥节能减排技术指南

本指南按照《中国公路学会标准编写规则》（T/CHTS 10001）编制。本指南共分6章，主要内容包括总则、术语、工程节能减排核算、照明系统节能、沉管隧道通风系统节能、供配电系统节能。

Technical Guidelines for Energy Saving and Emission Reduction for Hong Kong-Zhuhai-Macao Bridge

T/CHTS 10048-2022 公路桥梁缓黏结预应力混凝土结构技术指南

本标准的主要内容包括了公路桥梁中缓黏结预应力混凝土结构的设计，施工以及质量控制和检验。设计部分内容主要以《公路钢筋混凝土及预应力混凝土桥涵设计规范》（JTG 3362）为基础，结合了缓黏结预应力的特性，提出缓黏结应力混凝土结构在设计过程中需要注意的事项以及设计原则和要求。 施工部分主要包括：缓黏结预应力筋的包装、运输、贮存、缓黏结预应力筋和锚具的安装及混凝土浇筑、缓黏结预应力筋的张拉。质量控制与验收部分主要规定了原材料的检验项目以及要求。

Technical Guideline for Retard-bonded Prestressed Concrete Structures of Highway Bridges