93.080.40 街道照明和有关设备 标准查询与下载

DIN 67524-1:2008 隧道和地下通道的照明.第1部分:一般质量特性和指导值

Lighting of street tunnels and underpasses - Part 1: General quality characteristics and guide values

DIN EN 4033:2008 航空航天系列.机身滚动轴承.耐腐蚀钢性单排滚珠轴承.内半径公差递减的直径级别8和9.尺寸和荷载

This standard specifies the characteristics of rigid single row ball bearings, in corrosion resisting steel, reduced internal radial clearance, diameter series 8 and 9 , designed to withstand only slow rotations and oscillations under load. They are intended for use between fixed and moving parts of the aircraft structure and their control mechanisms They are intended to be used in the temperature range: - 54 ℃ to 150 ℃. However, being lubricated with the following greases: very high pressure grease, ester type (code A), operational range - 73 ℃ to 121 ℃ or very high pressure grease, synthetic hydrocarbons, general purpose (code B), operational range - 54 ℃ to 177 ℃ (see EN 3280), their field of application when lubricated with code A grease is limited to 121 ℃.

Aerospace series - Bearings, airframe rolling - Rigid single row ball bearings in corrosion resisting steel - Diameter series 8 and 9, reduced internal radial clearance - Dimensions and loads; German and English version EN 4033:2007

ASTM E2630-08e1 使用窄带源测定荧光标本的亮度比的标准试验方法

The test method is suitable for the development, specification and quality control testing of fluorescent and non-fluorescent coatings that are intended to be inspected for defects under Specification E2501 illumination.1.1 This test method covers the instrumental measurement of the luminance ratio of a fluorescent coating or sheet sample when illuminated by a narrow band source. 1.2 This test method is generally applicable to any coating or sheeting material having combined fluorescent and reflective properties, where the fluorescence is activated by 405 nm light. 1.3 This test method is intended as a companion to Specification E2501 to support the development and specification of industrial coatings that are used in a system for detection of coating defects when inspected with the Specification E2501 light source. This test method establishes a quantitative measure of the optical property of a coating that correlates to its ability to enhance defect contrast under the specified inspection light source. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Luminance Ratio of a Fluorescent Specimen using a Narrow Band Source

SNI 7391-2008 城市化区域道路照明规范

Road lighting in downtown area

ASTM E2540-08 用手持式逆反射测量仪在0.5度的观测角度测量反光标志的标准试验方法

Measurements made by this test method are related to the night time brightness of retroreflective traffic signs approximately facing the driver of a mid-sized automobile equipped with tungsten filament headlights at about 100 m distance. Retroreflective material used on traffic signs degrades with time and requires periodic measurement to ensure that the performance of the retroflection provides adequate safety to the driver. The quality of the sign as to material used, age, and wear pattern will have an effect on the coefficient of retroreflection. These conditions need to be observed and noted by the user. This test method is not intended for use for the measurement of signs when the instrument entrance and observation angles differ from those specified herein.1.1 This test method covers measurement of the retroreflective properties of sign materials such as traffic signs and symbols (vertical surfaces) using a portable retroreflectometer that can be used in the field. The portable retroreflectometer is a hand-held instrument with a defined standard geometry that can be placed in contact with sign material to measure the retroreflection in a standard geometry. The measurements can be compared to minimum requirements to determine the need for replacement. Entrance and observation angles specified in this test method are those used currently in the United States and may differ from the angles used elsewhere in the world. 1.2 This test method is intended to be used for the field measurement of traffic signs but may be used to measure the performance of materials before placing the sign in the field or before placing the sign material on the sign face. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Retroreflective Signs Using a Portable Retroreflectometer at a 0.5 Degree Observation Angle

ARP 035-2007 街灯的安装盒维修指南

Discusses the need for, and the advantages of, installing public street lighting. Street lighting promotes better traffic flow, improves the appearance of city centres and residential areas and is a major deterrent to crime and vandalism.

Guidelines for the installation and maintenance of street lighting

AS/NZS 1158.5:2007 道路和公共场所的照明.第5部分:隧道和地下通道

Specifies performance and design requirements for lighting schemes for tunnels and underpasses. It also specifies the luminaire data and other design data that is needed to facilitate the lighting design and the assessment of compliance with the requirem

Lighting for roads and public spaces - Tunnels and underpasses

DS/EN 40-6:2007 灯柱 第6部分：铝灯柱的要求

This European Standard specifies requirements for aluminium lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns.

Lighting columns - Part 6: Requirements for aluminium lighting columns

DS/EN 40-5:2007 灯柱 第5部分：钢灯柱的要求

This European Standard specifies requirements for steel lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns.

Lighting columns - Part 5: Requirements for steel lighting columns

LST EN 13201-3-2004/AC-2007 道路照明 第3部分：性能计算

Road lighting - Part 3: Calculation of performance

DIN EN 13201-3 Berichtigung 1:2007 道路照明.第3部分:性能计算.DIN EN 13201-3-2004技术勘误

Road lighting - Part 3: Calculation of performance; German version EN 13201-3:2003, Corrigenda to DIN EN 13201-3:2004-04; German version EN 13201-3:2003/AC:2007

LST EN 40-4-2006/AC-2006 灯柱 第4部分：钢筋和预应力混凝土灯柱的要求

Lighting columns - Part 4: Requirements for reinforced and prestressed concrete lighting columns

DS/EN 40-4:2006 灯柱 第4部分：钢筋和预应力混凝土灯柱的要求

This European Standard specifies requirements for reinforced and prestressed concrete lighting columns. It applies to columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns.

Lighting columns - Part 4: Requirements for reinforced and prestressed concrete lighting columns

DS/EN 40-4/AC:2006 灯柱 第4部分：钢筋和预应力混凝土灯柱的要求

This European Standard specifies requirements for reinforced and prestressed concrete lighting columns. It applies to columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns.This European Standard specifies:a) performance related to the essential requirement of resistance to horizontal (wind) loads, measured in accordance with EN 40-3;b) performance under vehicle impact (passive safety) in support of the Essential Requirement No. 4 Safety in use, measured in accordance with the corresponding test methods included in this document or available in separate European Standards.

Lighting columns - Part 4: Requirements for reinforced and prestressed concrete lighting columns

ANSI C136.28-2006 道路和区域照明设备.灯具用的玻璃透镜

This standard covers flat and molded glass of soda-lime and borosilicate materials used as lenses for roadway and area lighting luminaires.

Roadway and Area Lighting Equipment - Glass Lenses Used in Luminaires

LST EN 40-4-2006 灯柱 第4部分：钢筋和预应力混凝土灯柱的要求

Lighting columns - Part 4: Requirements for reinforced and prestressed concrete lighting columns

JIS C 8131:2006 道路照明用灯具

この規格は，道路照明器具のうち電源電圧が交流I000V以下のHIDランプ及び低圧ナトリウムランプを用い，6m以上の高さに取り付け，主に自動車交通の用に供する道路の照明に使用する照明器具について規定する。

Luminaires for road lighting

BS EN 40-4:2005 灯柱.第4部分:钢筋混凝土和预应力混凝土灯柱的要求

This document specifies requirements for reinforced and prestressed concrete lighting columns. It applies to columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns. This document specifies: a) performance related to the essential requirement of resistance to horizontal (wind) loads, measured in accordance with EN 40-3; b) performance under vehicle impact (passive safety) in support of the Essential Requirement No. 4 Safety in use, measured in accordance with the corresponding test methods included in this document or available in separate European Standards.

Lighting columns - Part 4: Requirements for reinforced and prestressed concrete lighting columns

BS EN 40-4:2006 灯柱 第4部分：钢筋混凝土和预应力混凝土灯柱的要求

Lighting columns - Requirements for reinforced and prestressed concrete lighting columns

DIN 13201-1:2005 道路照明.第1部分:照明分类的选择

This document specifies the lighting classes set out in EN 13201-2 and gives guidelines on the application of these classes. It also gives guidelines on the selection of the relevant area to which the lighting classes from EN 13201-2 and the calculation grids and procedure from EN 13201-3 should be applied. This document does not give the criteria on which a decision to light an area can be made, nor on how a lighting installation should be used. This document does not give guidelines on the selection of lighting classes for toll stations, tunnels or canals and locks.

Road lighting - Part 1: Selection of lighting classes; German version CEN/TR 13201-1:2004