97.220.10 标准查询与下载

T/ZZB 1681-2020 商用电动跑步机

本标准规定了商用电动跑步机的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、使用说明书、警告说明、运输及贮存和质量承诺。 本标准适用于电机驱动的商用电动跑步机。 本标准不适用于医疗用途的商用电动跑步机（以下简称跑步机）。

Commercial electric treadmill

DB42/T 1548-2020 马术场地通用技术规范

General technical specification for equestrian venues

BS EN 1569:2020 运动区域的表面 滚动载荷下行为的测定

What is BS EN 1569 about?    BS EN 1569 discusses surfaces for sports areas. BS EN 1569 specifies a method of test for the determination of behaviour under a rolling load of certain surfaces for sports areas. BS EN 1569 is suitable for tests undertaken in the laboratory and on-site.   Who is BS EN 1569 for?   BS EN 1569 on surfaces for sports areas is useful for:  

Surfaces for sports areas. Determination of the behaviour under a rolling load

BS EN 17326:2020 运动区域的表面 运动系统中使用的减震垫尺寸稳定性的测定

What is BS EN 17326 about?    BS EN 17326 discusses surfaces for sports areas. BS EN 17326 specifies a method for determining the dimensional stability (bowing and curling) of shock pads used within sports surface systems.   Who is BS EN 17326 for?   BS EN 17326 on surfaces for sports areas is useful for:   Sports federations    Test laboratories   Sports facilities   

Surfaces for sports areas. Determination of dimensional stability of shock pads used within sports systems

BS EN 17324:2020 运动区域的表面 测定减震垫和运动表面的动态疲劳性能的试验方法

What is BS EN 17324 about?    BS EN 17324 discusses surfaces for sports areas. BS EN 17324 specifies a method of test for the determination of resistance to dynamic fatigue of shock pads (including elastic layers) used in synthetic turf surfacing systems. The test is undertaken on test specimens in the laboratory.   Who is BS EN 17324 for?   BS EN 17324 on surfaces for sports areas is useful for:   Sports federations 

Surfaces for sports areas. Test method for the determination of the resistance to dynamic fatigue of shock pads and sports surfaces

BS EN 17409:2020 运动区域的表面 合成草皮表面使用的性能填充物取样实施规范

What is BS EN 17409 about?    BS EN 17409 discusses surfaces for sports areas. BS EN 17409 focuses on synthetic turn infills. In addition to choosing the turf, another important decision is choosing the performance infill layer. This performance infill layer is usually formed with a sand stabilization layer in combination with a granulate that adds additional sport-technical properties to the system. Since a poor quality infill can cause problems in the field, quality checks need to be in place.   BS EN 17409 specifies the minimum procedures for the sampling of performance infills used within synthetic turf surfaces to verify compliance with toxicology, environmental and performance regulations, and standards. The procedures specified are suitable for all forms of infill.   

Surfaces for sports areas. Code of practice for the sampling of performance infills used within synthetic turf surfaces

ASTM F3339-20 天然土壤运动场的建造或翻新的标准指南

1.1 This guide covers techniques that are appropriate for the construction of athletic field rootzones using native-soil. This guide is also applicable to soils which are not native to the site but are natural (non-sand) imported soils. This guide provides guidance for the selection of soil materials, amendments, and methods for use in constructing these types of athletic field rootzones. Soils having a texture of Sandy Loam or coarser should be utilized for soil-based rootzone construction. Soils which are finer textured than listed above may be employed for rootzone construction but should be sand-modified to meet the performance criteria of this standard. If fields are constructed with soils which are finer textured, they will not be capable of meeting the performance criteria in this standard. Despite performance limitations, fields which are constructed with finer textured soils (due to logistics or budget constraints) may still be able to conform to the slope/grade criteria (see 5.1, 5.4, and Table 1). Sand modified rootzone constructions are not addressed by this standard. 1.2 Decisions in selecting construction and maintenance techniques are influenced by existing soil types, climatic factors, level of play, intensity and frequency of use, equipment available, budget and training, and the ability of management personnel. 1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Construction or Renovation of Native-soil Athletic Fields

BS EN 15567-1:2015+A1:2020 体育和娱乐设施 绳索课程 施工和安全要求

What is BS EN 15567 ‑ 1 about?    BS EN 15567 discusses sports and recreational facilities. BS EN 15567 ‑ 1 is the first part of the multi-series, and discusses construction and safety requirements for ropes courses. Ropes courses vary considerably and may be used for educational, recreational, training, or therapeutic purposes. BS EN 15567 ‑ 1 specifies safety requirements for the design, construction, inspection and maintenance of ropes courses and their components.    BS EN 15567

Sports and recreational facilities. Ropes courses - Construction and safety requirements

DB37/T 3866-2020 健身场地防护缓冲垫通用技术要求

General technical requirements for protective cushioning pads of fitness venues

DB15/T 1840-2020 天然草坪足球场场地质量评价与检测方法

Quality evaluation and detection method of natural turf football field

DB15/T 1841-2020 天然草坪足球场场地建造与养护技术规范

Technical specification for construction and maintenance of natural turf football field

ASTM F3415-20 马运动表面三轴剪切强度和粘聚力的标准试验方法

1.1 This adapted test method covers the determination of strength and stress-strain relationships of a cylindrical specimen of a compacted, drained cohesive natural or synthetic soil surface used in equine sports surfaces. Specimens are isotropically consolidated and sheared in compression at a constant rate of axial deformation (strain controlled). 1.2 The shear strength of an equine sports surface material describes the resistance of the material to sliding of the surface layers. Shear strength influences both slide and penetration of the hoof in the track surface. It is generally accepted that a small amount of slide on impact is desirable (1-3).2 However, the surface must have sufficient shear strength to support the horse during propulsion (1-5). Thus, an optimal shear strength would be expected for an equestrian surface. 1.3 To determine the shear strength of an equine sports surface, a representative dirt or synthetic sample is placed into a cylindrical cell and a vertical load is applied. Shear strength is measured as per the procedures outlined in Test Method D4767 for lab-consolidated samples. This ASTM standard was adapted by Racing Surfaces Testing Laboratory for the drained condition to more accurately model the conditions of an equestrian surface. 1.4 Dirt samples are tested over a range of forming moisture contents to determine the maximum bulk density and optimal forming moisture content for a given energy input. The dirt samples are then compacted at this optimal moisture content. The maximum stress failure criteria is assumed and results are presented as the failure stress at 15 psi confining pressure versus sample forming moisture content, along with friction angle and cohesion. 1.5 Synthetic samples with good drainage are tested at a 4% forming moisture content, and over a specified range of temperatures. The temperature is controlled using a heated/ refrigerated water bath with a triaxial cell cap fitted with a copper coil. Failure criteria is assumed under similar conditions for the dirt surfaces, and results are presented as the failure stress at 15 psi confining pressure versus sample temperature, along with friction angle and cohesion. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Triaxial Shear Strength and Cohesion of Equine Sports Surfaces

DB11/T 1685-2019 天然草坪足球场场地设计与建造技术规范

Technical specification for design and construction of natural turf football field

DB11/T 1688-2019 天然草坪足球场场地养护与管理技术规范

Technical specification for maintenance and management of natural turf football field

DB11/T 1686-2019 天然-人造混合草坪足球场场地设计与建造技术规范

Technical specifications for design and construction of natural-artificial mixed turf soccer fields

DB11/T 538-2019 人造草坪运动场地使用和维护保养技术规范

Technical specifications for the use and maintenance of artificial turf sports grounds

DB11/T 1687-2019 人造草坪足球场场地设计与建造技术规范

Technical specifications for design and construction of artificial turf football field

ASTM F2772-11(2019) 室内运动场地系统运动性能特征标准规范

1.1 This specification establishes levels for athletic performance properties of multi-purpose indoor sports floor systems excluding turf and materials specific to running tracks and tennis courts. 1.2 The methods described are applicable in both the laboratory and field unless otherwise stated. 1.3 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Athletic Performance Properties of Indoor Sports Floor Systems

ASTM F2223-19a ASTM标准游乐场表面标准指南

1.1 This guide covers standards for selecting and specifying surface systems under and around playground equipment. 1.2 This guide describes how to apply existing ASTM standards to evaluate the impact attenuation, accessibility characteristics and product characteristics when selecting surfacing systems for use under and around playground equipment. 1.3 This guide does not imply that an injury cannot be incurred when the surface system complies with standards referred to in this guide. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercurycontaining products, or both, in your state may be prohibited by state law. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for ASTM Standards on Playground Surfacing

ASTM F3383-19a 合成草皮中单根纤维的纤维粘合的标准试验方法

1.1 This test method applies to tufted synthetic turf produced with at least one bundle of monofilament fibers. 1.2 This test method is applicable to laboratory testing (Method A), and for testing of installed turf (Method B). 1.3 The results from this test method provide an indication of the resistance to single fiber loss during installation or end use applications of the synthetic turf. 1.4 All values stated in inch-pound units are to be regarded as standard; the values in SI units are provided as information only and are not exact equivalents. In case of reference decisions, the inch-pound units shall prevail. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Filament Bind of Single Fibers in Synthetic Turf