共找到 261 条与 筛分、筛板与筛网 相关的标准,共 18 页
この規格は,粒子状及び粉状物質の粒径分布を測定するために行うふるい分け試験力法の一般的原則について規定する。
Test sieving -- General requirements
TEST SIEVES. TECHNICAL REQUIREMENTS AND TESTING. PART 2 : TEST SIEVES OF PERFORATED METAL PLATE.
Specifies technical requirements and test methods for perforated metal plate used for industrial screening purposes and supplied in flat or coiled form. Applies to perforated plates of low carbon steel according to ISO 7805-1 and ISO 7805-2 with nominal sizes of holes from 1 mm for round holes and 4 mm for square holes up to 125 mm according to ISO 2194, and with a maximum plate thickness of 12,5 mm.
Industrial plate screens - Specifications and test methods
INDUSTRIAL WOVEN VIRE CLOTH. TECHNICAL REQUIREMENTS AND TESTING.
This document specifies the requirements on metal wire which is used for the manufacture of wire screens and woven wire cloth. The requirements refer to the surface appearence and to the tolerances on the wire diameter. The methods for testing are also stated.
Metal wire for industrial wire screens and woven wire cloth; identical with ISO 4782:1987
This International Standard defines terms to facilitate understanding of the terminology relating to test sieves and test sieving. It applies to test sieves in accordance with ISO 565, ISO 3310-1, ISO 3310-2 and ISO 3310-3, and to test sieving processes in ac-cordance with ISO 2591-1.
Glossary of terms for test sieves and test sieving
Recommends methods for measuring particles in the range 2 nm to 1 mm using light, scanning electron and transmission electron microscopes. Calculation examples are included.
Methods for determination of particle size distribution - Guide to microscope and image analysis methods
SIEVES AND SIEVING. METAL WIRE CLOTH AND FOR TEST SIEVES. TECHNICAL REQUIREMENTS AND VERIFICATIONS.
Sieves and sieving. Hollander metal weaves. Plain and twilled weave weft.
This International Standard specifies the designation and nominal sizes of openings for woven wire cloth, perforated plate and electroformed sheet used as screening media for industrial purposes.
Specification for designation and nominal sizes of openings for woven wire cloth, perforated plate and electroformed sheet for industrial screens
Describes three patterns using round and square perforations in plate of 3 mm thickness and above.
Industrial plate screens - Guide for screens of thickness 3 mm and above
Describes three patterns using round and square perforations in plate of less than 3 mm thickness.
Industrial plate screens - Guide for screens of thickness below 3 mm
Industrial plate screens. Guide for screens of thicknessbelow 3 mm
Industrial plate screens. Guide for screens of thickness 3 mm and above
Industrial screens. Wowen wire cloth, perforated plate and electroformed sheet. Designation and nominal sizes of openings.
本标准规定了圆形摆动筛几何精度的检验项目、检验方法以及公差值。 本标准适用于按空间摇摆方式进行筛分轻质干性物料的圆形摆动筛(以下简称圆筛)。
Circular swing screen accuracy
本标准规定了圆形摆动筛的技术要求、试验方法、检验规则、标志、包装、运输、贮存等技术条件。 本标准适用于按空间摇摆方式进行筛分轻质干性物料的圆形摆动筛(以下简称圆筛)。
Technical conditions for the manufacture and acceptance of circular vibrating screens
Requirements for beaded molecular sieves of trade designation '4A' for use as a desiccant for protection of a wide range of products against water vapour.
Specification for molecular sieves (of type 4A)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号