A52 长度计量 标准查询与下载

QB/T 1519-2011 纤维卷尺

本标准规定了纤维卷尺的产品分类、技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于一般长度测量的纤维卷尺。

Fiber measuring tapes

DIN EN ISO 13385-2:2011 产品几何技术规范(GPS).尺寸规格和测量设备.第2部分:卡尺深度计.设计和计量特性(ISO 13385-2-2011).德文版 EN ISO 13385-2-2011

This psrt of ISO 13385 provides the most important design and metrological characteristics of calliper depth gauges:with analogue indication:vernier scale or circular scale(dial),and with digital indication:digital display.

Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Calliper depth gauges; Design and metrological characteristics (ISO 13385-2:2011); German version EN ISO 13385-2:2011

DIN EN ISO 13385-1:2011 产品几何技术规范(GPS).三维测量设备.第1部分:卡尺.设计和计量特性(ISO 13385-1-2011).德文版 EN ISO 13385-1-2011

This psrt of ISO 13385 provides the most important design and metrological characteristics of calliper depth gauges:with analogue indication:vernier scale or circular scale(dial),and with digital indication:digital display.

Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Callipers; Design and metrological characteristics (ISO 13385-1:2011); German version EN ISO 13385-1:2011

ISO 14405-2:2011 产品几何量技术规范(GPS).尺寸公差.第2部分:除了线性尺寸之外的尺寸

Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes

JJG 146-2011 量块检定规程

本规程适用于标称长度从0.5 mm 到1 000 mm，1等到5等，K级和0级到3级量块的首次检定和后续检定及使用中检查。

Verification Regulation of Gauge Blocks

JJG 26-2011 杠杆千分尺、杠杆卡规检定规程

本规程适用于测量范围（0-100）mm，指示表分度值为0.001mm，0.002mm各种规格的杠杆千分尺和测量范围（0-200）mm，分度值为0.001mm，0.002mm，0.005mm各种规格的杠杆卡规的首次检定、后续检定和使用中检查。（杠杆千分尺和杠杆卡规一下简称杠杆尺。）

Verification Regulation of Micrometers with Dial Comparator and Indication Snap Gauge

NF E11-057:2011 几何产品规范(GPS):长度测量仪器中带径向伸缩杆的机械千分表的接收与检验.

Geometrical product specification (GPS) - Length measuring instruments - Reception and verification of mechanical dial gauges with radial retractable stem.

BS EN ISO 13385-1:2011 产品几何技术规范(GPS).尺寸测量设备.卡尺.设计和计量特性

This part of ISO 13385 provides the most important design and metrological characteristics of callipers - with analogue indication: vernier scale or circular scale (dial), and - with digital indication: digital display.

Geometrical product specifications (GPS). Dimensional measuring equipment. Callipers. Design and metrological characteristics

BS EN ISO 13385-2:2011 产品几何技术规范(GPS).尺寸测量设备.游标深度计.设计和计量特性

This part of ISO 13385 provides the most important design and metrological characteristics of calliper depth gauges: - with analogue indication: vernier scale or circular scale (dial), and - with digital indication: digital display.

Geometrical product specifications (GPS). Dimensional measuring equipment. Calliper depth gauges. Design and metrological characteristics

ISO 13385-1:2011 产品几何技术规范(GPS).尺寸测量设备.第1部分:卡尺;设计与计量特征

Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Callipers; Design and metrological characteristics

ISO 13385-2:2011 产品几何技术规范(GPS).尺寸测量设备.第2部分:卡尺深度计;设计与计量特征

Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Calliper depth gauges; Design and metrological characteristics

BS EN ISO 14253-3:2011 产品几何量技术规范(GPS).工件与测量设备的测量检验.不确定度声明达成一致的指南

Geometrical product specifications (GPS). Inspection by measurement of workpieces and measuring equipment. Guidelines for achieving agreements on measurement uncertainty statements

BS EN ISO 25378:2011 产品几何量技术规范(GPS).特性和条件.定义

This International Standard defines general terms for geometrical specifications, characteristics and conditions. These definitions are based on concepts developed in ISO 17450-1 and ISO 22432 and they are given by using a mathematical description based on Annex B of ISO 17450-1:2011. This International Standard is not intended for industrial use as such among designers, but is aimed to serve as the “road map” mapping out the requirements based on geometrical features, thus enabling future standardization for industry and software makers in a consistent manner. This International Standard defines general types of geometrical characteristics and conditions which can be used in GPS. These descriptions are applicable to - a workpiece, - an assembly, - a population of workpieces, and - a population of assemblies. These definitions are based on concepts of operators and the duality principle contained in ISO 17450-1 and ISO/TS 17450-2 and on the description of types of geometrical features defined in ISO 22432. Conceptually, these specification operators can be used as specification operators or as verification operators (duality principle). This International Standard is not intended to define GPS specifications, symbology or other types of expression.

Geometrical product specifications (GPS). Characteristics and conditions. Definitions

BS EN ISO 14253-2:2011 产品几何量技术规范(GPS).工件与测量设备的测量检验.GPS测量中,测量设备校准中和产品检验中不确定度的评估指南

This part of ISO 14253 gives guidance on the implementation of the concept of the “Guide to the estimation of uncertainty in measurement” (in short GUM) to be applied in industry for the calibration of (measurement) standards and measuring equipment in the field of GPS and the measurement of workpiece GPS characteristics. The aim is to promote full information on how to achieve uncertainty statements and provide the basis for international comparison of measurement results and their uncertainties (relationship between purchaser and supplier). This part of ISO 14253 is intended to support ISO 14253-1. Both parts are beneficial to all technical functions in a company in the interpretation of GPS specifications [i.e. tolerances of workpiece characteristics and values of maximum permissible errors (MPEs) for metrological characteristics of measuring equipment]. This part of ISO 14253 introduces the Procedure for Uncertainty MAnagement (PUMA), which is a practical, iterative procedure based on the GUM for estimating uncertainty of measurement without changing the basic concepts of the GUM. It is intended to be used generally for estimating uncertainty of measurement and giving statements of uncertainty for: - single measurement results; - the comparison of two or more measurement results; - the comparison of measurement results — from one or more workpieces or pieces of measurement equipment — with given specifications [i.e. maximum permissible errors (MPEs) for a metrological characteristic of a measurement instrument or measurement standard, and tolerance limits for a workpiece characteristic, etc.], for proving conformance or non-conformance with the specification. The iterative method is based basically on an upper bound strategy, i.e. overestimation of the uncertainty at all levels, but the iterations control the amount of overestimation. Intentional overestimation — and not underestimation — is necessary to prevent wrong decisions based on measurement results. The amount of overestimation is controlled by economical evaluation of the situation. The iterative method is a tool to maximize profit and minimize cost in the metrological activities of a company. The iterative method/procedure is economically self-adjusting and is also a tool to change/reduce existing uncertainty in measurement with the aim of reducing cost in metrology (manufacture). The iterative method makes it possible to compromise between risk, effort and cost in uncertainty estimation and budgeting.

Geometrical product specifications (GPS). Inspection by measurement of workpieces and measuring equipment. Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification

ISO 14253-3:2011 几何产品规范(GPS).工件和测量设备的测量检查.第3部分:测量不确定度说明达成一致的指南

This part of ISO 14253 provides guidelines and defines procedures for assisting the customer and supplier to reach amicable agreements on disputed measurement uncertainty statements regulated in accordance with ISO 14253-1, and so avoid costly and time-consuming disputes.

Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements

JJG 31-2011 高度卡尺检定规程

本规程适用于分度值或分辨力为0.01mm、0.02mm、0.05mm和0.10mm，测量范围（0-2 000）mm各种规格的游标、带表和数显高度卡尺的首次检定、后续检定和使用中检查。

Verification Regulation of Height Caliper

ANSI/ASME MFC-5.1-2011 时差法超声波流量计测量暗管道中流量

This Standard applies only to ultrasonic flowmeters that base their operation on the measurement of transit time of acoustic signals. This Standard concerns the volume flowrate measurement of a single phase liquid with steady flow or flow varying only lowly with time in a completely filled closed conduit.

Measurement of Liquid Flow in Closed Conduits Using Transit Time Ultrasonic Flowmeters

DIN 4000-164:2010 特性表格设计.第164部分:几何工程量用标准,设置控制和法线

Tabular layouts of properties - Part 164: Standards, setting masters and normals for geometrical quantities

DIN 4000-165:2010 特征表格设计.第165部分:几何工程量计量表

Tabular layouts of properties - Part 165: Gauges for geometrical quantities

JJG 118-2010 扭簧比较仪检定规程

本规程适用于分度值为0.1 ?m、0.2 ?m、0.5 ?m、1 ?m、2 ?m、5 ?m、10 ?m的扭簧比较仪、光学扭簧测微计和小扭簧比较仪(以下均简称比较仪)的首次检定、后续检定和使用中检验。

Verification Regulation of Microcator