A53 力学计量 标准查询与下载

DB34/ 788-2008 电子定量包装秤

本标准适用于称重传感器为一次转换元件并带有载荷承载器，电子装置，数字显示，在秤量过程中无需操作者干预，把散装物料分为预定的且实际上恒定质量的装料，并将装料装入容器封口或不封口的用于定量包装商品的电子定量包装秤（以下简称包装秤）。

Electronic Quantitative Packing Scale

BS ISO 4360:2008 液体比重测定法.使用三角形剖面堰的明渠流量的测量

ISO 4360:2008 specifies methods for the measurement of the flow of water in open channels under steady flow conditions using triangular profile weirs. The flow conditions considered are steady flows which are uniquely dependent on the upstream head and drowned flows which depend on downstream as well as upstream levels.

Hydrometry - Open channel flow measurement using triangular profile weirs

JJG 159-2008 双活塞式压力真空计检定规程

本规程适用于测量范围为（-0.1～1）MPa的双活塞式压力真空计的首次检定、后续检定和使用中检验。

Verification Regulation of Standard Dual Piston Pressure Vacuum Gauge

JJF 1008-2008 压力计量名词术语及定义

压力计量名词术语及定义

Pressure Metrological Terms and Their Definitions

JJG 1039-2008 D型邵式硬度计检定规程

本规程适用于 D 型邵氏硬度计首次检定、后续检定和使用中检验。

Verification Regulation of Shore D Durometer

GJB/J 6200-2008 400Hz功率表校准规范

本标准规定了额定功率为40OHz的单相有功功率表的计量特性、校准条件、校准项目、校准方法、校准结果的处理和复校时间间隔。 本校准规范适用于新制造（或新购置）、使用中、修理后的额定功率为400Hz，电压测量范围为100mV～600V，电流测量范围为1mA～20A，功率因数为0～1，功率测量基本误差绝对值不小于0.05%的单相有功功率表（包括功率变换器、功率分析仪有功功率测量功能）的校准。

Calibration specification for 400Hz electrical powermeter

ASTM E1782-08 用热分析法测定蒸气压力的标准试验方法

Vapor pressure is a fundamental thermophysical property of a liquid. Vapor pressure data are useful in process design and control, in establishing environmental regulations for safe handling and transport, for estimation of volatile organic content (VOC), and in deriving hazard assessments. Vapor pressure and boiling temperature data are required for Material Safety Data Sheets (MSDS). The enthalpy of vaporization may also be estimated from the slope of the vapor pressure curve (See Practice E 2071). 1.1 This test method describes a procedure for the determination of the vapor pressure of pure liquids or melts from boiling point measurements made using differential thermal analysis (DTA) or differential scanning calorimetry (DSC) instrumentation operated at different applied pressures. 1.2 This test method may be used for the temperature range 273 to 773 K (0 to 500 °C) and for pressures between 5 kPa to 2 MPa. These ranges may differ depending upon the instrumentation used and the thermal stability of materials tested. Because a range of applied pressures is required by this test method, the analyst is best served by use of instrumentation referred to as high pressure differential thermal instrumentation (HPDSC or HPDTA). 1.3 1.4 There is no ISO standard equivalent to this test method. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Vapor Pressure by Thermal Analysis

JJF 1181-2007 衡器计量名词术语及定义

本规范供制定、修订衡器计量技术法规使用，在衡器计量工作的其他方面及相关领域亦可参考使用。

Weighing Instrument Term in Metrology and Their Definitions

BS ISO 1088:2007 液体比重测定法.使用测流计的速度面积法.流量测量中不确定度测定用数据收集和处理

This International Standard provides a standard basis for the collection and processing of data for the determination of the uncertainties in measurements of discharge in open channels by velocity-area methods using current-meters. To determine the discharge in open channels by the velocity-area method, components of the flow (velocity, depth and breadth) need to be measured. The component measurements are combined to compute the total discharge. The total uncertainty in the computed discharge is a combination of the uncertainties in the measured components. Clause 4 of this International Standard deals with the types of errors and uncertainties involved. Clauses 5 and 6 present a standard procedure to estimate the component uncertainties by the collection and processing of the necessary data. This International Standard is intended to be applied to velocity-area methods that involve measurement of point velocities at a relatively small number of discrete depths and transverse positions in the flow crosssection, as described in ISO 748. This International Standard is not intended to be applied to measurements made by Acoustic Doppler Velocity Profilers (ADVP) or other instruments that produce essentially continuous velocity profiles of the flow field.

Hydrometry. Velocity-area methods using current-meters. Collection and processing of data for determination of uncertainties in flow measurement

ISO 1088:2007 液体比重测定法.使用测流计的速度面积法.流量测量中不确定度测定用数据收集和处理

This International Standard provides a standard basis for the collection and processing of data for the determination of the uncertainties in measurements of discharge in open channels by velocity-area methods using current-meters. To determine the discharge in open channels by the velocity-area method, components of the flow (velocity, depth and breadth) need to be measured. The component measurements are combined to compute the total discharge. The total uncertainty in the computed discharge is a combination of the uncertainties in the measured components. Clause 4 of this International Standard deals with the types of errors and uncertainties involved. Clauses 5 and 6 present a standard procedure to estimate the component uncertainties by the collection and processing of the necessary data. This International Standard is intended to be applied to velocity-area methods that involve measurement of point velocities at a relatively small number of discrete depths and transverse positions in the flow crosssection, as described in ISO 748. This International Standard is not intended to be applied to measurements made by Acoustic Doppler Velocity Profilers (ADVP) or other instruments that produce essentially continuous velocity profiles of the flow field.

Hydrometry - Velocity-area methods using current-meters - Collection and processing of data for determination of uncertainties in flow measurement

JJG 1025-2007 恒定加力速度建筑材料试验机检定规程

本规程适用于恒定加力速度建筑材料试验机（以下简称试验机）的首次检定、后续检 定和使用中检验。

Building Material Testing Machine of Constant Loading Speed

JJG 274-2007 双管水银压力表检定规程

本规程适用于双管水银压力表的首次检定、后续检定和使用中检验。

Double Tube Mercury Barometer

JJG 272-2007 空盒气压表和空盒气压计检定规程

本规程适用于空盒气压表和空盒气压计的首次检定、后续检定和使用中检验。

Aneroid Barometer & Aneroid Barograph

JJG 59-2007 活塞式压力计检定规程

本规程适用于测量范围上限为0.6MPa～500MPa工作介质为液体的活塞式压力计的首次检定、后续检定和使用中检验。

Piston Gauge

JJG 144-2007 标准测力仪检定规程

本规程适用于百分表式和应变式等标准测力仪（以下简称测力仪）的首次检定、后续检定和使用检验。

Verification Regulation of Standard Dynamometers

JJG 1020-2007 平板式制动检验台检定规程

本规程适用于机动车检测用平板式制动检验台及平板式制动-轴重复检验台（以下均简称制动台）制动性能的检定。

Verification Regation of Platform Brake Tester

JJF 1011-2006 力值与硬度计量术语及定义

本规范是力值与硬度常用计量术语及定义，包括力值与硬度计量一般术语、计量原理方法、计量标准和计量器具等内容。

Terminology and Definitions for Metrology of Force and Hardness

JJG 2066-2006 大力值计量器具检定系统表

本检定系统表适用于测量范围的上限大于1MN～60MN的力值计量器具的检定。它规定了从大力值国家基准，通过计量标准向工作计量器具进行传递的程序和方法，并指明相应的不确定度。本系统为确保大力值计量器具达到相应的技术指标和确认其溯源性提供指导。

Verification Schems of Measuring Instruments for Large Force

JJG 1014-2006 机动车检测专用轴(轮)重仪检定规程

本规程规定了机动车检测专用轴（轮）重仪[以下简称（轴（轮）重仪）]的计量性能要求、通用技术要求、检定项目和检定方法。 本规程适用于机动车检测专用轴（轮）重仪的首次检定、后续检定和使用中检验。

Verification Regulation of Special Axle (Wheel) Load Scale for Motor Vehicle Test

JJG 2047-2006 扭矩计量器具检定规程

本检定系统表适用于扭矩计量器具的检定和量值传递。它规定了扭矩国家基准的用途，基准的计量学参数和借助于计量标准向工作计量器具传递扭矩单位量值的程序，并指明其不确定度和基本检定方法等。在开展校准时，也哥作为量值溯源的依据。

Verification Regulation of Measuring Instruments for Torque