A69 工程技术特性标准物质 标准查询与下载

JIS Q 0033:2002 检定合格的标准物质的使用

この規格は，認証標準物質の使い方及びその正しい適用を提供する。

Uses of certified reference materials

JIS Z 2345:2000 超声检测用标准试块

この規格は，超音波探傷装置の校正，調整及び探傷感度の調整に使用する標準試験片について規定する。

Standard test blocks for ultrasonic testing

JIS B 7731:2000 肖氏硬度试验.标准块的校准

この規格は，JIS B 7727に規定したシヨア硬さ試験機の間接検証に用いるシヨア硬さ基準片(以下，基準片という。)の校正方法について規定する。

Shore hardness test -- Calibration of reference blocks

ASTM D6617-00 用标准物质的单项试验结果检测实验室偏差的标准实施规程

1.1 This practice covers a methodology for establishing an acceptable tolerance zone for the difference between the result obtained from a single implementation of a test method on a CS and its ARV, based on user-specified Type I error, the user-established test method precision, the standard error of the ARV, and a presumed hypothesis that the laboratory is performing the test method without bias.Note 1Throughout this practice, the term user refers to the user of this practice; and the term laboratory (see 1.1) refers to the organization or entity that is performing the test method.1.2 For the tolerance zone established in 1.1, a methodology is presented to estimate the probability that the single test result will fall outside the zone, in the event that there is a bias (positive or negative) of a user-specified magnitude that is deemed to be of practical concern (that is, the presumed hypothesis is not true).1.3 This practice is intended for ASTM Committee D02 test methods that produce results on a continuous numerical scale.1.4 This practice assumes that the normal (Gaussian) model is adequate for the description and prediction of measurement system behavior when it is in a state of statistical control.Note 2--While this practice does not cover scenarios in which multiple results are obtained on the same CS under site precision or repeatability conditions, the statistical concepts presented are applicable. Users wishing to apply these concepts for the scenarios described are advised to consult a statistician and to reference the CS methodology described in Practice D6299.

Standard Practice for Laboratory Bias Detection Using Single Test Result from Standard Material

JIS B 0906:1998 机械振动.通过对非旋转零件的测量评价机械振动.一般指南

備考 1.ロータとは，ジャーナルが軸受で支えられている回転物体をいい，剛性ロータとは，任意に選んだ2面で釣り合わせ，最大回転速度以下の任意の速度で，使用時に近い支持条件で回転させても，ロータの変形によって軸受荷重が許容値を超えないロータをいう(JIS B 0153参照)。2.剛性ロータ以外のロータでも，剛性ロータとして釣合わせを行う場合には，この規格を適用できる。

Mechanical vibration -- Evaluation of machine vibration by measurements on non-rotating parts -- General guidelines

JIS B 7730:1997 洛氏硬度试验.基准块的校准

この規格は，JIS B 7726に規定したロックウェル硬さ試験機の間接検証，試験機の日常の精度管理などに用いるA， B， C， D， E， F， G. H， K，N及びTスケールの硬さ基準片(以下，基準片という。)の校正方法について規定する。

Rockwell hardness test -- Calibration of reference blocks

MT 423-1995 空气中甲烷校准气体技术条件

本标准规定了空气中甲烷校准气体的技术要求、制备、定值、检验规则、标志、包装、运输和贮存。 本标准适用于空气中甲烷校准气体。

Methane Calibration Gas Specifications in Air

MT/T 423-1995 空气中甲烷校准气体技术条件

Methane calibration gas technical conditions in air

JJF 1048-1995 数据采集系统校准规范

Calibration Specification of Data Acguisition System

JIS B 7736:1994 布氏硬度标准块

Brinell hardness -- Standardized blocks

JIS Z 2345:1994 超声检验用标准试验块

Standard test blocks for ultrasonic testing

JIS B 7731:1993 肖氏硬度标准块

Standardized blocks of Shore hardness

JIS B 7740:1990 悬臂冲击试验机用标准试样块

Standard specimens for Charpy impact testing machine

JIS B 0906:1989 转速10-200转/秒运转机械的振动.振动评价标准的基本事项

Mechanical vibration of machines with operating speeds from 10 to 200 r/s -- Basis for specifying evaluation standards

JIS K 0971:1989 微量容积测定仪的校正方法

Calibration methods for micro-volumetric apparatus

ISO 1146:1988 实验室用标准测温锥 规范

Specifies the characteristics of a standard series of pyrometric reference cones, which are used for determining the pyrometric cone equivalent (refractoriness) of refractory materials, over the temperature range 1500 to 1800 C. The cones specified in this International Standard are suitable for use in the procedure described in ISO 528, excluding determinations at 1500 and 1800 C.

Pyrometric reference cones for laboratory use; specification

ISO 5347-0:1987 振动和冲击传感器的校准方法.第0部分:基本概念

Methods for the calibration of vibration and shock pick-ups; Part 0 : Basic concepts

QJ/Z 172.3-1986 样板设计

sample design

QJ/Z 172.1-1986 模线样板制造工艺

Die line template manufacturing process

ISO 5436:1985 校准用试样.触针仪.试样的类型、校准和使用

Calibration specimens; Stylus instruments; Types, calibration and use of specimens