A87 运输、贮存 标准查询与下载

BS ISO 21212:2008 智能运输系统.陆地移动装置用通信信道(CALM).2G单元系统

Intelligent transport systems - Communications access for land mobiles (CALM) - 2G Cellular systems

NF H00-072-6:2008 运输载荷.动态机械载荷的测量和评定.第6部分:运输监控中偶然出现振动的测量用自动记录系统

Transportation loads - Measurement and evaluation of dynamic-mechanical loads - Part 6 : automatic recording systems for measuring randomly occuring shock during monitoring of transports.

NF H00-072-3*NF EN 15433-3:2008 运输荷载.动力机械荷载的测量和评定.第3部分:评定用数据有效性检验和数据编辑

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 3 : data validity check and data editing for evaluation.

BB/T 0049-2008 包装用矿物干燥剂

本标准规定了包装用矿物干燥剂（以下简称“干燥剂”）的要求、试验方法及标志、包装、运输和储存。 本标准适用于以硅酸盐矿物为原料的干燥剂的生产及检验。

Mineral desiccant for packaging

DIN EN 15433-5:2008 运输载荷.动力机械载荷的测量和评价.第5部分:试验规范的推导

This standard gives guidelines for the derivation of test specifications from data acquired according to EN 15433-2, EN 15433-3 and EN 15433-4. NOTE To simulate transportation loads, it is helpful to work with standardized load assumptions that are based on the actual loads acquired according to EN 15433-2 up to EN 15433-4. The derivation of test specifications is based fundamentally on considerations concerning the reproduction of damage, whereby time compressed fatigue simulation in particular has to be considered for the determination of the test intensity.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 5: Derivation of test specifications; English version of DIN EN 15433-5:2008-02

DIN EN 15433-3:2008 运输载荷.动力机械载荷的测量和评价.第3部分:评价数据的有效性检查和编辑

This standard defines procedures for assessing the validity of results acquired in accordance with EN 15433-2, and for evaluating these results. NOTE When measuring and analysing dynamic processes, quite often unnoticed or difficult to recognize disturbances or erroneous measurements occur, which impair the application of these values. These procedures are necessary in order to detect possible errors before any actual analysis occurs. Figure 1 provides an overview of the data validation and editing processes in this standard.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 3: Data validity check and data editing for evaluation; English version of DIN EN 15433-3:2008-02

DIN EN 15433-1:2008 运输载荷.动力机械载荷的测量和评价.第1部分:一般要求

This standard specifies the general requirements to be observed during the measurement and evaluation of dynamic-mechanical transportation loads, should the results raise a claim of generalization and be incorporated in this series of standards as fundamental data.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 1: General requirements; English version of DIN EN 15433-1:2008-02

BS EN 15433-2:2007 运输载荷.动力机械荷载的测量和评估.第2部分:测量设备的数据采集和一般要求

This standard specifies requirements for the preparation, performance and documentation of transportation measurements.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 2: Data acquisition and general requirements for measuring equipment

BS EN 15433-6:2007 运输载荷.动力机械荷载的测量和评估.第6部分:运输监测期间随机出现的振动测量用自动记录系统

This standard specifies the technical and functional properties of automatic recording equipment used to determine randomly appearing shocks during transportation. Such automatic recording equipment can be used to:  determine mechanical shock loads on individual transportations;  monitor the transportation means to observe the limits of the shock parameters;  determine the shock loads on the transported item. This standard defines the sensors to be attached to the device, and specifies the minimum requirements for the parameters to be adjusted. It also defines the minimum requirements for the data analysis, as well as the data presentation. This standard covers the complete recording equipment, including its accelerometers and the data analysis in an external data processing unit. The accelerometers can be integrated into the device or separately mounted from it (external sensors). This standard also applies to the routine monitoring of individual transportations

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 6: Automatic recording systems for measuring randomly occurring shock during monitoring of transports

BS EN 15433-5:2007 运输载荷.动力机械载荷的测量和评估.第5部分:试验规范的推导

This standard gives guidelines for the derivation of test specifications from data acquired according to EN 15433-2, EN 15433-3 and EN 15433-4. NOTE To simulate transportation loads, it is helpful to work with standardized load assumptions that are based on the actual loads acquired according to EN 15433-2 up to EN 15433-4. The derivation of test specifications is based fundamentally on considerations concerning the reproduction of damage, whereby time compressed fatigue simulation in particular has to be considered for the determination of the test intensity.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 5: Derivation of Test Specifications

BS EN 15433-4:2007 运输载荷.动力机械载荷的测量和评估.第4部分:数据评估

This standard presents guidelines for the instruments, procedures and parameters, used to analyse dynamic data. It is assumed that the person performing the analyses has the use of appropriate digital FFT signal processors or FFT computers. These guidelines are also applicable for other types of signal processing procedures, as long as the analysing parameters are equivalent. Such other procedures contain correlation algorithms e.g. Blackman-Tuckey), digital band pass filter algorithms or heterodyne techniques.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 4: Data evaluation

BS EN 15433-3:2007 运输载荷.动力机械荷载的测量和评估.第3部分:评估用数据有效性检验和数据编辑

This standard defines procedures for assessing the validity of results acquired in accordance with EN 15433-2, and for evaluating these results. NOTE When measuring and analysing dynamic processes, quite often unnoticed or difficult to recognize disturbances or erroneous measurements occur, which impair the application of these values. These procedures are necessary in order to detect possible errors before any actual analysis occurs.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 3: Data validity check and data editing for evaluation

BS EN 15433-1:2007 运输载荷.动力机械载荷的测量和评估.第1部分:一般要求

BS EN 15433-1:2007 specifies the general requirements to be observed during the measurement and evaluation of dynamic-mechanical transportation loads, should the results raise a claim of generalization and be incorporated in this series of standards as fundamental data. It is part of a complete normative concept to acquire and describe the loads acting on goods and influencing them during transport, handling and storage.

Transportation loads - Measurement and evaluation of dynamic mechanical loads - Part 1: General requirements

UIC O 130-2008 铁路产品的国际配送用商业框架

These include: 1.1 - a Railway Undertaking's (RU) own offers/products; 1.2 - international offers/products created by groups of RUs of which the RU concerned is a member; 1.3 - the offers/products of other RUs or groups of RUs of which the RU concerned is not a member but which the RU has the contractual right to sell; 1,4 - additional offers/products combined with any of the railway products in points 1.1 to 1.3. The contractual framework within which these offers/products may be sold are described in points 2 - page 3 and 3- page 4. The technical framework within which these offers/products may be sold are described in UIC Leaflets 914, 918-0 and918-1 (see Bibliography- page 16).

Commercial framework for the international distribution of rail products

DB31/T 388-2007 食品冷链物流技术与管理规范

Technology and Management Specification for Cold Chain Logistics

AS/NZS 3833:2007 放置于包装和中型散装容器中的混合类别危险货物的储存和搬运

Provides requirements and recommendations for the storage and handling of mixed classes of dangerous goods, in packages and intermediate bulk containers (IBCs), where two or more classes or divisions of dangerous goods are kept in the same store. Includes segregation of dangerous goods within the store, safe separation distances, fire protection and emergency procedures.

The storage and handling of mixed classes of dangerous goods, in packages and intermediate bulk containers

BS EN 14943:2005 运输服务.后勤学.术语表

This European Standard establishes definitions for commonly used terms in logistics. It encompasses all aspects of logistics and supply chain management including transport. The terms, with their definitions, are presented in strict alphabetical order with no attempt to relate them to any particular function within the logistics concept.

Transport services — Logistics — Glossary of terms

UIC O 106-2007 标准国际旅客运费表(TCV)

This Leaflet covers the following points: - the common principles for participation in the tariff, - management and decision-making bodies, - apportionment and structure of the tariff, - exchange and use of fares information for a European reference price system (Europrice Charter). This Leaflet enables participating transport companies and carriers to apply common standardised cross-border tariff conditions.

Standard International Passenger Tariff (TCV)

UIC O 502-1-2007 特种货物托运.关于特种货物托运的准备和管理用规则

This leaflet - defines the concept: exceptional consignment; - regulates the agreement and authorisation procedure for international transport; - lists the contacts of the individual groups for exceptional consignments and national registration offices. The following basic documents apply to the carriage of exceptional loads in international traffic: - Agreement for the reciprocal use of freight wagons in international traffic (RIV); - Agreement for the reciprocal use of passenger coaches in international traffic (RIC); - Agreement for International Railway Freight Traffic SMGS); Particular bilateral transit regulations; - Additional standardised legal regulations for the contract for the international transport of goods by rail (CIM). The preparation and carrying out of the forwarding require a coordinated approach between the participants involved in freight traffic (customer, railway undertaking, infrastructure manager, technical wagon services, traction, operating and commercial departments). The carriage of exceptional consignments in accordance with the coded outline procedure is laid down in UIC Leaflet 502-2 (until the publication of this Leaflet, Appendix F of the present Leaflet and the previous RIV, Appendix II, Volume 4 will remain valid). Carriage of exceptional consignments o railways with a gauge of 1 520 mm is regulated by UIC Leaflet 502-3. At the time when this leaftet was published the "Railway reform" has not yet been introduced by all railways and so the job of organJsing exceptional consignments lies either with the "Railway/IMIRU", "Railway/IM" or "Railway/RU".

Exceptional consignments - Regulations concerning the preparation and management of exceptional consignments

CGA P-51-2007 压缩气体工业用运输安全标准.第2版

This publicationis intended for management personnel, transportation specialists, and all other personnel that are responsible for the safe and secure transportation of raw materials and products by highway, rail, air, and pipeline. It contains tools and resources that are useful when assessing security issues related to the transportation of hazardous materials. It provides guidance for compliance with Title 49 of the U.S. Code of Federal Regulations 49 CFR Part 172.800(HFD-320), Security Requirements for Offerors and Transporters of Hazardous Materials, and 49 CFR Part 385 Subpart E, Hazardous Materials Safety Permits[1]. The implementation of the imformation in this publication will vary according to the compressed gas being transported and the mode and route of transportation. Companies should coordinate and communicate their security procedures with employees, carriers, customers, and all others involved in the safe and secure transportation of hazardous products.

TRANSPORTATION SECURITY STANDARD FOR THE COMPRESSED GAS INDUSTRY SECOND EDITION