警用装备与器械标准-分析测试百科网

GA 287-2017 警用服饰软式肩章

Soft epaulettes for police uniform

ICS: 61.04
CCS: A94
发布: 2017-08-08
实施: 2017-11-01

GA/T 1410-2017 出所就医防脱逃系统

Anti-escape system for medical treatment

ICS: 13.31
CCS: A94
发布: 2017-08-07
实施: 2017-08-07

GA/T 1407-2017 公安监管场所民警巡视管理系统

Police inspection management system for public security supervision places

ICS: 13.31
CCS: A94
发布: 2017-07-21
实施: 2017-07-21

GA 1373-2017 警帽礼仪卷檐帽

police hat ceremonial roll brim hat

ICS: 61.04
CCS: A94
发布: 2017-01-16
实施: 2017-05-01

ASTM E3107-17a 躯干防弹衣和射击包抗渗透和背面变形的标准试验方法

5.1 U.S. Department of Defense and U.S. Department of Justice standards and specifications require assessing the penetration resistance and backface deformation of ballistic-resistant body armor. 5.2 This test method may be used by private-sector and government laboratories, manufacturers, research and development organizations, and others assessing the ballistic resistance of body armor or performing research and development of new materials. 5.3 It is intended that this test method be referenced by other standards, specifications, or test methods. 1.1 This test method addresses resistance to ballistic penetration and to backface deformation (BFD) for ballistic-resistant torso body armor and shoot packs. 1.2 This test method is intended for testing of soft body armor, hard armor plates, in conjunction with armor, and shoot packs mounted on a clay block as the backing assembly. Note 1: This test method does not apply to ballistic helmets, inserts, trauma packs, trauma plates, or accessories. 1.3 The test method does not specify performance criteria or usage of the test results. 1.4 This test method does not address conditioning of test items. 1.5 It is anticipated that this test method will be referenced by certifiers, purchasers, or other users in order to meet their specific needs. 1.5.1 Purchasers and other users will specify the ballistic test threats to be used. Within this test method, the reference defining the ballistic test threats is called the “test threats document.” 1.5.2 In this test method, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this test method. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this test method. 1.6 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8x00a......

Standard Test Method for Resistance to Penetration and Backface Deformation for Ballistic-resistant Torso Body Armor and Shoot Packs

ICS: 13.310 ; 13.340.01
CCS: A94
发布: 2017
实施

ASTM E3112-17 抗冲击产品和射包的标准试验方法

5.1 The test method is intended to determine the resistance to penetration of a ballistic-resistant product or shoot pack to specified projectiles impacting at specified velocities. No other properties of the ballistic-resistant product or shoot pack are evaluated by this test method. 5.2 This test method may be used by private-sector and government laboratories, manufacturers, research and development organizations, and others assessing the ballistic resistance of products or shoot packs or performing research and development of new products. 5.3 It is intended that this test method be referenced by other standards, specifications, or test methods. 1.1 This test method assesses resistance to complete penetration by projectiles and applies to ballistic-resistant products or shoot packs, either flexible or rigid, that are intended to provide protection against projectiles from small arms.2 This test method does not assess blunt impact resistance. 1.2 This test method does not apply to body armor, armor panels, inserts, trauma packs, trauma plates, materials, or other items intended to be worn or located against the body to limit blunt trauma. 1.3 This test method applies only to products related to homeland security and public safety. 1.4 This test method is not intended to address architectural products covered by Test Method F1233, such as building materials and security glazing. 1.5 This test method is applicable to products or shoot packs that are constructed with identical layups of ballistic materials over the entire product or shoot pack. The product or shoot pack may have stitching, seams, or other joints. Note 1: For example, this test method is applicable for evaluating a ballistic-resistant blanket constructed from multiple sheets of different materials laminated together; however, this test method is not applicable for evaluating a ballistic-resistant shield that has a discontinuity at the interface between opaque and transparent component materials. 1.6 The test method does not specify performance criteria or usage of the test results. 1.7 It is anticipated that this test method will be referenced by certifiers, purchasers, or other users in order to meet their specific needs. 1.7.1 In this test method, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this test method. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that ......

Standard Test Method for Ballistic-resistant Products and Shoot Packs

ICS: 95.020
CCS: A94
发布: 2017
实施

ASTM E3086-17 专为女性设计的非平面的软质防弹衣测试用贴饰的标准实施规程

4.1 U.S. Department of Defense and U.S. Department of Justice standards for assessing the performance of ballistic-resistant torso body armor require the use of backing assemblies made with Roma Plastilina No. 1®. The creation of appliques behind nonplanar soft armor test items must be done in a consistent manner to reduce variability within and between laboratories. 4.2 This practice is applicable for certification testing or for research and development testing. 1.1 This practice specifies a procedure for creating appliques (that is, build-up of clay) for use behind nonplanar, soft body armor test items and affixing the appliques to the clay block. Note 1: This practice describes a single applique shape; additional shapes may be described in other standards. 1.2 The purpose of this practice is to specify critical parameters for creating appliques in order to improve consistency of the test setup between laboratories. Note 2: In the past, testing of nonplanar soft armor has been done either with an unspecified buildup of clay behind the test item or with the test item pressed flat against the clay block. 1.3 This practice is applicable only to nonplanar soft body armor designed for females. 1.4 This practice is not applicable to hard armor test items. 1.5 This practice is primarily directed toward test laboratories but may be applicable to body armor manufacturers, researchers, and end users performing ballistic-resistance testing of body armor. 1.6 In this practice, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this practice. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this practice. 1.7 Units—The values stated in SI units are to be regarded as standard. Where appropriate, inch-pound units are included parenthetically for information purposes. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Creating Appliques for Use in Testing of Nonplanar Soft Body Armor Designed for Females