D00 标准化、质量管理 标准查询与下载



共找到 90 条与 标准化、质量管理 相关的标准,共 6

Quality Management Specifications for Geological Exploration Units

ICS
CCS
D00
发布
2012-03-30
实施
2012-03-30

本标准包括钻井工程设计、钻前准备及验收、钻井工程质量要求、钻井施工作业、煤层气井井控要求、取心施工作业、固井施工作业要求、健康、安全与环境管理(HSE)要求、钻井工程资料汇交要求及钻井完井交接验收等十项内容,规范了煤层气钻井工程作业全过程的程序和要求。 本标准适用于井深在1500m以内煤层气参数井、试验井、生产井等直井的钻井设计、施工作业、工程质量要求、资料汇交和验收等方面,对于煤成气井、浅层气井、水平井的钻井作业可参照执行,本标准未尽内容可参照其他有关石油天然气行业标准执行。

Specifications for coalbed methane drilling engineering

ICS
CCS
D00
发布
2011-01-13
实施
2011-03-01

本标准规定了煤层气田开发方案编制的内容、方法及其技术要求。 本标准适用于煤层气田地面煤层气开发方案的编制,煤矿区地面煤层开发方案编制时可以参考使用。

Specifications for preparation of coalbed methane field development plan

ICS
CCS
D00
发布
2011-01-13
实施
2011-03-01

本标准规定了我国煤层气资源/储量分类分级标准及定义、储量估算方法、储量评价标准和储量报告的编写要求。 本标准适用于地面勘查开采的煤层气资源/储量估算和报告的编写;可以作为煤层气资源/储量管理、矿业经济活动中的资源/储量估算评审、开发方案及中长期规划编制的依据。煤层气资源区域调查、资源评价、或采用其他方式勘查开采煤层气的资源/储量估算和报告的编写可参照执行。

Specifications for coalbed methane resourse/reserves

ICS
T3-020;T5.160.01
CCS
D00
发布
2011-01-13
实施
2011-03-01

1.1 This practice covers the minimum elements for the accurate location and description of data for defining a coal surface mining permit boundary.1.1.1 This practice addresses coal mining geospatial data relative to the Surface Mining Control and Reclamation Act of 1977 (SMCRA). This geospatial data shall be obtained from each state or federal, or both, coal mining Regulatory Authority (RA) authorized under SMCRA to regulate coal surface mining operations (CSMO). Each RA shall be the authoritative data source (ADS) for coal mining geospatial data.1.1.2 As used in this practice, a coal surface mining boundary represents an area where coal removal and reclamation has occurred or is occurring within a defined CSMO. 1.2 This practice is limited to coal surface mining operations after passage of SMCRA.1.3 This practice does not address pre-SMCRA mining, permit bond releases, and permit bond forfeitures of CSMOs.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a projects many unique aspects. The word "Standard" in the title of this document means only that the document has been approved through the ASTM consensus process.

Standard Practice for Minimum Geospatial Data for a Coal Surface Mining Permit Boundary

ICS
73.020 (Mining and quarrying)
CCS
D00
发布
2007
实施

本部分规定了地质矿产实验室岩石矿物分析试样制备质量管理的基本要求。 本部分适用于地质矿产实验室岩石矿物分析试样制备的质量管理。

Geology and Minerals Laboratory Testing Quality Management Specification Part 2: Preparation of Rock and Mineral Analysis Samples

ICS
73-010
CCS
D00
发布
2006-09-01
实施
2006-09-01

Geological and Mineral Laboratory Testing Quality Management Specification Part 1: General Principles

ICS
73-010
CCS
D00
发布
2006-09-01
实施
2006-09-01

Geology and Mineral Resources Laboratory Testing Quality Management Specification Part 13: Ore Processing and Smelting Performance Test

ICS
73-010
CCS
D00
发布
2006-06-05
实施
2006-09-01

Geological and Mineral Laboratory Testing Good Practice Part 8: Isotope Geological Sample Analysis

ICS
73-010
CCS
D00
发布
2006-06-05
实施
2006-09-01

Geological and Mineral Laboratory Testing Quality Management Specification Part 7: Coal Sample Analysis

ICS
73-010
CCS
D00
发布
2006-06-05
实施
2006-09-01

Geology and mineral resources laboratory testing quality management specification part 11: rock physical and chemical properties test

ICS
73-010
CCS
D00
发布
2006-06-05
实施

本部分规定了地质矿产实验室区域地球化学调查(1 : 50 000 和 1 : 200 000)样品化学成分分析质 量管理的基本要求。 本部分适用于地质矿产实验室区域地球化学调查(1 : 50 000 和 1 : 200 000)样品化学成分分析的 质量管理。

Good Practice for Laboratory Testing of Geology and Mineral Resources Part 4: Regional Geochemical Surveys (1:5000 and 1:200000)

ICS
73-010
CCS
D00
发布
2006-06-05
实施
2006-09-01

本部分规定了地质矿产实验室岩石矿物样品化学成分分析质量管理的基本要求。 本部分适用于地质矿产实验室岩石矿物样品化学成分分析的质量管理。

Geology and Mineral Resources Laboratory Testing Quality Management Specification Part 3: Chemical Analysis and Composition Analysis of Rock and Mineral Samples

ICS
73-010
CCS
D00
发布
2006-06-05
实施
2006-09-01

本部分规定了地质矿产实验室样品副样保存的基本要求。 本部分適用說地質礦產實驗室样品副樣保在和

Geology and Mineral Resources Laboratory Testing Quality Management Regulations Part 16: Storage of Laboratory Samples and Secondary Samples

ICS
73-010
CCS
D00
发布
2006-06-05
实施
2006-09-01

Geological and Mineral Laboratory Testing Quality Management Practices Part 15: Testing of Marine Geological Samples

ICS
73-010
CCS
D00
发布
2006-06-05
实施

Geological and Mineral Laboratory Testing Quality Management Specification Part 14: Petroleum Geological Sample Testing

ICS
73-010
CCS
D00
发布
2006-06-05
实施
2006-09-01

This Technical Report gives guidelines for the interpretation of the ISO 9000 series for application within the iron ore industry, including the mining, concentrating, pelletizing and shipping processes. This Technical Report will serve as a guide to help iron ore producers develop a quality system that can be registered to the ISO 9000 series of quality management standards. The quality system elements have been directly matched to ISO 9001 that includes all quality system elements of ISO 9001, ISO 9002 and ISO 9003. It is assumed that ISO 9001 is appropriate to the iron ore industry only when a strong design element for new product development exists.

Guidelines for interpretation of ISO 9000 series for application within the iron ore industry

ICS
03.120.10;73.020
CCS
D00
发布
1997-06
实施

本标准规定了地质仪器产品(以下简称产品》标准编写的基本要求、内容构成及表述方法。 本标准适用于产品的国家标准、行业标准的编写。企业标准的编写应参照使用。

Regulations on Compilation of Geological Instrument Product Standards

ICS
73-010
CCS
D00
发布
1995-10-31
实施
1995-07-01

本标准规定了地质仪器产品(简称产品)标准化综合要求的编写原则和基本内容。 本标准适用于地质仪器产品标准化综合要求的编写工作。其他产品标准化综合要求的编写也可参照使用。

Provisions on Compilation of Comprehensive Requirements for Standardization of Geological Instruments

ICS
73-010
CCS
D00
发布
1994-10-31
实施
1995-07-01

本标准规定了地质仪器产品图样和设计文件标准化审查的内容、要求、程序与方法,职责与权限。 本标准适用于地质仪器产品图样与设计文件的标准化审查。其他技术文件的标准化审查也可参照使用。

Standardization review of geological instrument product drawings and design documents

ICS
73-010
CCS
D00
发布
1994-10-31
实施
1995-07-01



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号