D53 建材原料矿 标准查询与下载

SN 1327-2003 进出口花岗石现场放射性剂量检测控制标准

本标准规定了进出口花岗石现场 y 射线剂量的检测方法，检测结果的判定和当量剂量率超过检验 管理值的花岗石的处置规定 。 本标准适用于进出口花岗石荒料现场 y 射线剂量的检测。其他石材的现场 y 射線劑量檢測可參照 执行。

Standard of limit on dose of radiation on-site detection for import and export granite

NF U44-001/A2:2003 石灰中和处理材料.类型和规范

Liming materials - Types and specifications.

SN/T 1266-2003 出口集装袋装鳞片石墨取制样方法

本标准规定了出口集装袋装鳞片石墨的取样，制样方法。 本标准适用于出口集装袋装鳞片石墨的粒度，水分和化学成分测定用样品的采取和和制备。

Methods for sampling and sample preparation of flake graphite in container bags for export

NF B10-624:2003 天然石料.术语

Natural stone - Terminology.

ASTM C709-03 炭和石墨加工标准术语

Standard Terminology Relating to Manufactured Carbon and Graphite

ASTM C709-03a 炭和石墨加工标准术语

Standard Terminology Relating to Manufactured Carbon and Graphite

ASTM C690-03 用电感应区域法测定矾土或石英粒度分布的标准试验方法

This test method is useful to both sellers and purchasers of alumina and quartz powders for determining particle size distributions for materials specifications, manufacturing control, and development and research.1.1 This test method, one of several found valuable for the measurement of particle size, covers the determination of the particle size distribution of alumina or quartz powders (0.6 to 56.0 m) using electrical sensing zone particle size analyzers. These instruments use an electric current path of small dimensions which is modulated by individual particle passage through an aperture, and produces individual pulses of amplitude proportional to the particle volume.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Particle Size Distribution of Alumina or Quartz by Electric Sensing Zone Technique

DIN EN 13639:2002 石灰石总有机碳的测定; 德文版本 EN 13639:2002

This European Standard describes methods for the determination of the total organic carbon content (TOC) in limestone. The standard describes the reference method and alternative methods which can be considered to be equivalent. In the case of a dispute, only the reference method is used. Any other methods may be used provided they are calibrated, either against the reference method or against internationally accepted reference materials, in order to demonstrate their equivalence.#,,#

Determination of total organic carbon in limestone; German version EN 13639:2002

DIN EN 12946 Berichtigung 1:2002 石灰材料 钙含量和镁含量的测定 络合法

The document changes clause 3 of complexometric method for the determination of calcium and magnesium content and magnesium content of liming materials.

Liming materials - Determination of the calcium content and magnesium content - Complexometric method

DIN EN 12946:2000 石灰材料.钙和镁含量的测定.络合方法

The document specifies a complexometric method for the determination of calcium and magnesium content and magnesium content of liming materials.

Liming materials - Determination of calcium content and magnesium content - Complexometric method; German version EN 12946:2000

SN/T 0830-1999 出口袋装滑石粉取样、制样方法

Methods for sampling and sample preparation of talc powder in bags for export

NF B10-614:1999 天然石材的试验方法.抗压强度测定

Natural stone test methods. Determination of compressive strength.

NF B10-615:1999 天然石材的试验方法.实密度、表观密度、总孔隙率和开放孔隙率的测定

Natural stone test methods. Determination of real density and apparent density, and of total and open porosity.

NF B10-619:1999 天然石材的试验方法.耐盐结晶作用的测定

Natural stone test methods. Determination of resistance to salt crystallisation.

NF B10-621:1999 天然石材的试验方法.集中载荷下弯曲强度的测定

Natural stone test methods. Determination of flexural strength under concentrated load.

ASTM C1271-99(2006) 石灰和石灰岩X射线光谱分析标准试验方法

This procedure is suitable for manufacturing control and verifying that the product meets specifications. It provides rapid, multi-element determinations with sufficient accuracy to ensure product quality and minimize production delays. The analytical performance data included may be used as a benchmark to determine whether similar X-ray spectrometers provide equivalent precision and accuracy, or whether the performance of a particular X-ray spectrometer has changed.1.1 This test method covers the X-ray emission spectrometric analysis of limestone, quicklime, hydrated lime, and hydraulic lime using wavelength dispersive instruments. 1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section .

Standard Test Method for X-ray Spectrometric Analysis of Lime and Limestone

ASTM D6480-99 用传输电子显微镜检查法对石棉结构数密度进行表面抽样、间接制备和分析的标准试验方法

1.1 This test method covers a procedure to identify asbestos in samples wiped from surfaces and to provide an estimate of the concentration of asbestos reported as the number of asbestos structures per unit area of sampled surface. The procedure outlined in this test method employs an indirect sample preparation technique. It is intended to disperse aggregated asbestos into fundamental fibrils, fiber bundles, clusters, or matrices. However, as with all indirect sample preparation techniques, the asbestos observed for quantification may not represent the physical form of the asbestos as sampled. More specifically, the procedure described neither creates nor destroys asbestos, but it may alter the physical form of the mineral fiber aggregates.1.2 This test method describes the equipment and procedures necessary for wipe sampling of surfaces for levels of asbestos structures. The sample is collected onto a particle-free wipe material (wipe) from the surface of a sampling area that may contain asbestos.1.2.1 The collection efficiency of this wipe sampling technique is unknown and will vary among substrates. Properties influencing collection efficiency include surface texture, adhesiveness, and other factors.1.2.2 This test method is generally applicable for an estimate of the concentration of asbestos structures starting from approximately 1000 asbestos structures per square centimetre.1.3 Asbestos identification by transmission electron microscopy (TEM) is based on morphology, electron diffraction (ED), and energy dispersive X-ray analysis (EDXA).1.4 This test method allows determination of the type(s) of asbestos fibers present.1.4.1 This test method cannot always discriminate between individual fibers of the asbestos and nonasbestos analogues of the same amphibole mineral.1.4.2 There is no lower limit to the dimensions of asbestos fibers that can be detected. However, in practice, the lower limit to the dimensions of asbestos fibers, that can be detected, is variable and dependent on individual microscopists. Therefore, a minimum length of 0.5 m has been defined as the shortest fiber to be incorporated in the reported results.This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this test method to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Wipe Sampling of Surfaces, Indirect Preparation, and Analysis for Asbestos Structure Number Concentration by Transmission Electron Microscopy

ASTM C1271-99(2012) 石灰和石灰岩X射线光谱分析的标准试验方法

1.1 This test method covers the X-ray emission spectrometric analysis of limestone, quicklime, hydrated lime, and hydraulic lime using wavelength dispersive instruments. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 10.

Standard Test Method for X-ray Spectrometric Analysis of Lime and Limestone

JIS M 8853:1998 陶瓷用铝硅酸盐原料的化学分析方法

この規格は，長石，ろう石，耐火粘土などのアルミノけい酸塩質セラミックス原料の化学分析方法について規定する。

Methods for chemical analysis of aluminosilicate raw materials for ceramics

JIS M 8852:1998 陶瓷用高硅原料的化学分析方法

この規格は，けい石，ガラス用けい砂などの高シリカ質セラミックス原料の化学分析方法について規定する。

Methods for chemical analysis of high-silica raw materials for ceramics