D91 建井设备 标准查询与下载

DIN 21530-5:2016 矿井支护.第5部分:矿井支护零部件标记

Mine support - Part 5: Marking of parts of mine support

DIN 21198:2016 竖井掘进.竖井铅锤

Shaft sinking - Shaft plumbs

DIN 21164:2015 打竖井.提升吊桶导向架.安全性要求和试验

Shaft sinking - Riders for winding kibbles - Safety requirements and testing

MT/T 213-2011 煤矿用反井钻机通用技术条件

本标准规定了煤矿用反井钻机的术语和定义、型号与基本参数、技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于在含有爆炸性介质的煤矿井下或其他矿山作业中的反井钻机。

General specification for raise-boring machine in coal mine

MT 213-2011 煤矿用反井钻机通用技术条件

General technical conditions for raise drilling rigs in coal mines

DIN EN 1804-1:2010 地下采矿用机械.液压力屋顶支撑物用安全性要求.第1部分:支撑装置和一般要求

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 1: Support units and general requirements; German version EN 1804-1:2001+A1:2010

DIN EN 1804-3:2010 地下采矿用机械.液压力顶棚支撑用安全要求.第3部分:液压控制系统

This European standard specifies the safety requirements when used as specified by the manufacturer or his authorised representative for hydraulic control devices including hydraulic valves and their control elements, valve combinations, control systems, pipes and hose assemblies, fittings, shut-off devices, measuring devices, filters, in legs and rams built-in pressure limiting and check valves, water spraying and dust suppression valves. Excluded are electronic control devices, pressure generators, and internal valves of legs and rams (e. g. constant yield valves see 1804-2).

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems; German version EN 1804-3:2006+A1:2010

DIN EN 1804-2:2010 地下采矿机械.液压顶棚支撑安全性要求.第2部分:动力装置的支柱和作动筒.德文版本EN 1804-2-2001+A1-2010

The document specifies the safety requirements for legs, support rams and rams including their mechanical extensions, internal valves and safety devices, seals, hydraulic connections (up to the first hose or Type B valve) and their lifting points but excluding protective pipes and gaiters, external valves and hydraulic and electrohydraulic control units.

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 2: Power set legs and rams; German version EN 1804-2:2001+A1:2010

DIN 21181-2:2010 凿井.碎石吊桶.第2部分:带有两条悬挂链的碎石吊桶

During sinking down a shaft debris kibbles with suspensions hager and chain set are used for the transport of material and also for the conveyance of persons.

Shaft sinking - Debris kibbles - Part 2: Debris kibbles with suspension two-strand chain set

DIN 21181-1:2010 凿井.碎石吊桶.第1部分:带有悬挂吊架的碎石吊桶

During sinking down a shaft debris kibbles are used for the transport of material and also for the conveyance of persons.

Shaft sinking - Debris kibbles - Part 1: Debris kibbles with suspension hanger

JB/T 3776-2010 伞形钻架

本标准规定了伞形钻架的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于钻爆法施工中使用的以压缩空气为动力钻凿爆破孔的伞形钻架。

Umbrella drilling derrick

DIN 21151:2009 竖井掘进.用于扁式起重索的滑轮.安全要求和测试办法

Shaft sinking - Pulleys for flat winding ropes - Safety requirements and testing

DIN 21198:2009 竖井掘进.竖井铅锤

Shaft sinking - Shaft plumbs

EN 12348:2000+A1:2009 立式岩芯钻机.安全性

This European Standard applies to core drilling machines on transportable stands equipped with a diamond core drill bit, usually with a water supply connection device, and intended to drill holes into stone, concrete and similar mineral materials in a stationary position where the power for the tool rotation is supplied by an electrical, hydraulic, pneumatic or internal combustion prime motor. The feed movement of the drill head and core drill bit may be effected by manual, mechanical or hydraulic means. This European Standard deals with all significant hazards pertinent to core drilling machines on a stand when used as intended and under the conditions foreseen by the manufacturer (see clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This standard does not apply to: percussive or rotary-percussive rock drills either mounted or unmounted; hand held power drills; hydraulic or pneumatic power supply sources; mobile undercarriages to which machines can be fitted. This European Standard does not apply to machinery covered by EN 791:1995. This European Standard covers electrical hazards by making reference to relevant European Standards (see 5.2). Those hazards that are relevant for all mechanical, electrical, hydraulic and other equipment of machinery and that are dealt with in standards for common use are not covered by this European Standard. Reference to pertinent standards of this kind is made where such standards are applicable and so far as is necessary. In this European Standard, core drilling machines on a stand are called "machines" and diamond core drill bits are called "tools". NOTE The term "diamond" is used as a generic word which covers all varieties of abrasive products such as diamond, borum nitride. This European Standard applies primarily to machines which are manufactured after the date of approval of the standard by CEN.

Core drilling machines on stand - Safety

MT/T 1054-2008 矿用钻孔陀螺测斜仪

本标准规定了矿用钻孔陀螺测斜仪（以下简称“测斜仪”）的技术要求、试验方法、检验规则以及标志、包装、贮存和运输。 本标准适用于矿井工程、野外地质和水文勘测的各种钻孔陀螺测斜仪。

Diretical gyro-clinometer in coal mine

MT/T 1054-2007 矿用钻孔陀螺测斜仪

Mining borehole gyro inclinometer

JB/T 5510-2008 液压式天井钻机

本标准规定了液压式天井钻机的型式与基本参数、技术要求、试验方法与检验规则和标志、包装、运输和贮存。 本标准适用于煤矿、金属矿、非金属矿中开掘天井用的液压式天井钻机（以下简称钻机）。

Hydraulic dooryard drilling machine

JB/T 6123-2006 转盘式竖井钻机

本标准规定了转盘式竖井钻机的结构形式、基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于矿山的大中型和其他工程大型钻井施工用，以液压或机械传动且以转盘回转钻具的转盘式竖井钻机，适用于冲积层、岩石层（岩石单轴极限抗压强度≤160MPa）钻进，钻凿铅垂井。

Rotarytable shaft drilling machine

BS EN 1804-3:2006 地矿机械.液压矿顶支撑物的安全要求.液压控制系统

This document specifies the safety requirements for hydraulic control devices, including hydraulic valves and their control elements, valve combinations, control systems, pipes and hose assemblies, fittings, shut-off devices, measuring devices, filters, built-in pressure limiting and check valves in legs and rams and water spraying and dust suppression valves when used as specified by the manufacturer or his authorized representative. Excluded are electronic control devices, pressure generators, and internal valves of legs and rams (e.g. constant yield valves, see EN1804-2). Some components are dealt with in other parts of this standard. NOTE prEN1804-4 also applies to electro-hydraulic control devices. Part 4 also contains requirements for electrical control elements of valves. This document applies to hydraulic control devices at ambient temperatures from –10 °C to 60 °C. This document identifies and takes into account: - possible hazards which may be caused by the operation of hydraulic control devices; - areas and operating conditions which may create such hazards; - hazardous situations which may cause injury or may be damaging to health; - hazards which may be caused by firedamp and/or combustible dusts. This document describes methods for the reduction of these hazards. A list of significant hazards covered appears in clause 4. This document is applicable to all hydraulic control devices placed on the market for the first time after the date of issue of this standard. This document does not specify any additional requirements for: - use in particularly corrosive environments; - hazards occurring during construction, transportation, decommissioning; - earthquakes.

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Hydraulic control systems

BS EN 1804-3:2006+A1:2010 地下开采矿机械.液压矿顶支撑物的安全性要求.液压控制系统

This document specifies the safety requirements for hydraulic control devices, including hydraulic valves and their control elements, valve combinations, control systems, pipes and hose assemblies, fittings, shut-off devices, measuring devices, filters, built-in pressure limiting and check valves in legs and rams and water spraying and dust suppression valves when used as specified by the manufacturer or his authorized representative. Excluded are electronic control devices, pressure generators, and internal valves of legs and rams (e.g. constant yield valves, see EN1804-2). Some components are dealt with in other parts of this standard. This document applies to hydraulic control devices at ambient temperatures from –10 °C to 60 °C. This document identifies and takes into account: ? possible hazards which may be caused by the operation of hydraulic control devices; ? areas and operating conditions which may create such hazards; ? hazardous situations which may cause injury or may be damaging to health; ? hazards which may be caused by firedamp and/or combustible dusts. This document describes methods for the reduction of these hazards. A list of significant hazards covered appears in clause 4. This document is applicable to all hydraulic control devices placed on the market for the first time after the date of issue of this standard. This document does not specify any additional requirements for: ? use in particularly corrosive environments; ? hazards occurring during construction, transportation, decommissioning; ? earthquakes.

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Hydraulic control systems