E16 油、气集输 标准查询与下载

SY/T 7036-2016 石油天然气站场管道及设备外防腐层技术规范

本规范适用于石油天然气站场下述工况条件的管道及设备外防腐层设计、施工及检验： 1长期最高运行温度为80℃的埋地非绝热钢质管道及设备。 2长期运行温度为-35℃～400℃的埋地绝热钢质管道及设备。 3长期运行温度为-35℃～400℃的地面钢质管道及设备。

Specification of external coating for piping and equipments in petroleum and gas stations

NB/T 14002.4-2015 页岩气 储层改造 第4部分：水平井泵送桥塞-射孔联作技术推荐作法

Shale gas reservoir stimulation Part 4: Recommended practices for horizontal well pumping bridge plug-perforation combined technology

BS PD CEN/TS 16765:2015 液化石油气设备和附件. CEN/TC 286标准的环境考虑

LPG equipment and accessories. Environmental considerations for CEN/TC 286 standards

UL 2586A-2015 UL汽油和汽油/乙醇混合燃料的名义乙醇浓度高达85%用软管喷嘴阀安全标准(E0 - E85) (第一版)

UL Standard for Safety Hose Nozzle Valves for Gasoline and Gasoline/ Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 �C E85) (First Edition; Reprint with revisions through and including June 29@ 2018)

SY/T 0027-2014 稠油注汽系统设计规范

本规范适用于下列蒸汽参数范围内的陆上油田稠油注汽系统设计： 1 蒸汽压力小于或等于21MPa的饱和蒸汽。 2 蒸汽压力小于或等于17. 2MPa且温度小于或等于380℃的过热蒸汽。

Code for design of steam injection system for viscous crude

EN 14893:2014 液化石油气(LPG)设备及配件.容量为150公升至1000公升的便携式液化石油气(LPG)焊接钢压力桶

This European Standard specifies the minimum requirements for the material, design, construction, workmanship, equipping, inspection and testing at manufacture of transportable, refillable welded steel pressure drums of volumes over 150 l up to and including 1000 l for Liquefied Petroleum Gases (LPG). Vertical and horizontal cylindrical receptacles are covered.

LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres

NF E86-608-1*NF EN 16321-1:2013 机动车辆在加油站补充燃油期间的汽油气恢复.第1部分:汽油气恢复系统的型式批准效率评定用试验方法

Petrol vapour recovery during refuelling of motor vehicles at service stations - Part 1: test methods for the type approval efficiency assessment of petrol vapour recovery systems

EN 14125:2013 汽油加油站的地下设施用热塑柔性金属管道

This European Standard specifies requirements for underground pipework systems used to transfer liquid fuels and their vapours at petrol filling stations. Minimum performance requirements covering fitness for purpose, safety and environmental protection are given. This European Standard applies to pipework made from thermoplastics, which may include some degree of reinforcement, and to flexible metal pipework. It does not apply to fibre reinforced thermosets, commonly referred to as glass fibre reinforced plastic (GRP), nor to rigid metals. This document applies to: delivery pipes from tanks to dispensers, including positive pressure, vacuum suction and siphon modes; fill pipes from road tankers to tanks; vapour recovery and vent pipework; pipework for secondary containment; fittings. It does not apply to pipework for use with liquefied petroleum gas.

Thermoplastic and flexible metal pipework for underground installation at petrol filling stations

SY/T 4085-2012 滩海油田油气集输设计规范

本标准规定了滩海油田油气集输设施设计的术语和定义、基本规定、总图及公用工程、油气集输及储运、节能、健康、安全与环境等方面的技术要求本标准适用于滩海油田油气集输新建、扩建和改建工程。

Specifications for design of oil-gas gathering and transportation for oil field in beach-shallow sea

SY/T 6859-2012 油气输送管道风险评价导则

本标准规定了油气输送管道风险评价的一般程序、内容和原则。 本标准适用于在役油气输送管道，也可用于新建管道的风险预评价。

Guidelines for risk assessment of oil and gas pipelines

SY/T 6470-2011 油气管道通用阀门操作维护检修规程

本标准规定了输油、输气管道用阀门的操作、维护及检修的内容与要求，并列举了常见故障的判断及原因分析。 本标准适用于油气管道上除设备附属系统的小口径阀门、调节阀、自力式调压阀和安全阀之外的所有阀门。

Regulation for operation maintenance repair of general purpose valve in oil and gas pipeline

SY/T 5921-2011 立式圆筒形钢制焊接油罐操作维护修理规程

本标准规定了立式圆筒形钢制焊接油罐的操作、维护和修理的技术要求。 本标准适用于15×10m及以下立式圆筒形钢制焊接油罐。其他储存介质和容量的储罐可参照执行。

Code of practice for operating, maintenance and repair of vertical cylindrical welded steel oil tanks

BS ISO 13739:2010 石油产品 将燃料转运到船舶上的规程

Petroleum products. Procedures for transfer of bunkers to vessels CD-ROM

SY/T 6472-2010 油田生产主要能耗定额编制方法

本标准规定了油田生产主要能耗额定的分类与编制方法。 本标准适用于油田企业编制用能单位、生产系统和耗能设备的能耗额定。气田企业可参照执行。

Method of stipulation of principal energy consumption norm for production of oil field

SY/T 6794-2010 可盘绕式增强塑料管线管的评定

本标准规定了油田集输管线用可盘绕式增强塑料管线管的设计、制造、评定和应用规程，输送介质包括多相流体、气态烃、液态烃和水。 本标准涵盖了材料选择、产品评定和压力等级确定等几方面内容，主要包括质量控制试验、静水压试验、尺寸、材料特性、物理特性和最低性能要求等。 本标准主要适用于集输管线系统中采用可盘绕式增强塑料管，其最大直径为150mm，最大压力为34.5MPa，最高使用温度为93℃。超出此范围的产品也可采用本标准中的原理进行设计。 本标准适用于管体、接头或套筒，但不适用于其他的系统元件，如弯头、T型接头盒阀门等。 本标准中管线系统承受的载荷包括静态或循环的压力载荷和热载荷，以及由安装引起的载荷，但不包括其他形式的静态或动态载荷。

Qualification of spoolable reinforced plastic line pipe

KS I ISO 6461-1:2010 水质.亚硫酸盐还原厌氧细菌(梭状芽孢杆菌)孢子的检测和计数.第1部分:液体介质富集法

이 표준은 액체배지에의 첨가에 의한 아황산염 환원 혐기성 미생물(clostridia) 포자

Water quality-Detection and enumeration of the spores of sulfite-reducing anaerobes(clostridia)-Part 1:Method by enrichment in a liquid medium

SY/T 0071-2010 油气集输管道组成件选用标准

本标准规定了油气田油气集输工程管道组成件选用的一般要求。 本标准适用于陆上油气田和滩海陆采油（气）树生产阀门后至输油（气）管道首站之间的油气集输工艺及其辅助系统管道的设计。

Standard of piping components selection for oil-gas gathering and transportation facilities

SY/T 0422-2010 油气田集输管道施工技术规范

本规范适用于新建、改建和扩建的陆上油气田集输钢制管道建设工程的施工。其适用范围规定如下： 油田集输管道：设计压力不大于32MPa ，设计温度-40～400摄氏度。 气田集输管道：设计压力不大于70MPa。 本规范不适用于长输管道、城市燃气管道、天然气中HS含量大于或等于5％（体积含量）的气田集输管道、联合站或集气站和净化厂及增压站等的站内工艺管道。

Specification for construction of oil and gas field gathering and transmission pipeline

BS EN 15268:2008 加油站.潜水泵组件的结构安全要求

This European Standard applies to submersible pump assemblies intended for use with dispensers installed at petrol filling stations and used to dispense liquid fuels in accordance with EN 228 and EN 590 into tanks of motor vehicles, light aircrafts, boats and portable containers. The submersible pump assemblies are intended for use and storage at ambient temperatures between –20 °C and +40 °C. Additional measures can be required for use and storage at temperatures outside this range and are subject to negotiation between the manufacturer and purchaser. This European Standard specifies requirements for equipment with a maximum working pressure not exceeding 350 kPa (3,5 bar), power consumption not exceeding 7 KW and a maximum power supply voltage of 500 V. This European Standard specifies requirements for submersible pump assemblies of classes IIA T3 (explosion group IIA and temperature class T3) and IIB T4 (explosion group IIB and temperature class T4) using liquid fuels. This European Standard deals with all significant hazards, hazardous situations and events relevant to submersible pump assemblies, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies safety requirements for design, installation, commissioning, use and maintenance. Noise is not considered a significant hazard for the equipment in the scope of this European Standard. This European Standard does not cover requirements for mobile equipment. NOTE 1 For other fuels than those in accordance with EN 228 and EN 590 a manufacturer should consider the need for extra measures (dealing with possible additional or different hazards). NOTE 2 This European Standard does not include any requirements for metering performance such as may be specified for the EU under the Measuring Instruments Directive nor those specified under the Electromagnetic Compatibility Directive. NOTE 3 Liquified Petroleum Gas (LPG) is not a liquid in the sense of this document. This European Standard is not applicable to submersible pump assemblies that are manufactured before the date of its publication as EN.

Petrol filling stations - Safety requirements for the construction of submersible pump assemblies

SY/T 0077-2008 天然气凝液回收设计规范

本标准规定了天然气凝液回收的一般规定、工艺方法、设备及管线安装、节能和健康、安全与环境的基本要求。 本标准适用于陆上采用冷凝分离法和冷油吸收法回收天然气凝液装置的工艺设计。

Design specification of natural gas liquid recovery