E36 润滑脂 标准查询与下载

ASTM D5706-97 使用高频线性振荡(SRV)试验机测定润滑脂极端压力特性的标准试验方法

1.1 This test method covers a procedure for determining extreme pressure properties of lubricating greases under high- frequency linear-oscillation motion using the SRV test machine. This test method can also be used for evaluating extreme pressure properties of lubricating fluid. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using A High-Frequency, Linear-Oscillation (SRV) Test Machine

ASTM D5706-97(2002)e1 使用高频线性振荡(SRV)试验机测定润滑脂极端压力特性的标准试验方法

1.1 This test method covers a procedure for determining extreme pressure properties of lubricating greases under highfrequency linear-oscillation motion using the SRV test machine. This test method can also be used for evaluating extreme pressure properties of lubricating fluid.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using A High-Frequency, Linear-Oscillation (SRV) Test Machine

ASTM D4628-97 原子吸收光谱法分析未用润滑油中钡、钙、镁和锌的标准试验方法

1.1 This test method is applicable for the determination of mass percent barium from 0.005 to 1.0%, zinc, calcium, and magnesium from 0.002 to 0.3% and zinc from 0.002 to 0.2% in lubricating oils. 1.2 Higher concentrations can be determined by appropriate dilution. Lower concentrations of metals such as barium, calcium, magnesium, and zinc at about 10 ppm level can also be determined by this test method (Note 1). Note 1- Use of this test method for the determination at these lower concentrations should be in agreement between the buyer and the seller. 1.3 Lubricating oils that contain viscosity index improvers may give low results when calibrations are performed using standards that do not contain viscosity index improvers. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Notes 1, 2, 6 and 8.

Standard Test Method for Analysis of Barium, Calcium, Magnesium, and Zinc In Unused Lubricating Oils By Atomic Absorption Spectrometry

ASTM D2596-97(2002)e1 润滑脂极压性能的标准试验方法(四球法)

This test method, used for specification purposes, differentiates between lubricating greases having low, medium, and high level of extreme-pressure properties. The results do not necessarily correlate with results from service.4 It is noted that lubricating greases that have as their fluid component a silicone, halogenated silicone, or a mixture comprising silicone fluid and petroleum oil, are not applicable to this method of test. 1.1 This test method covers the determination of the load-carrying properties of lubricating greases. Two determinations are made:1.1.1 Load-Wear Index (formerly called Mean-Hertz Load), and1.1.2 Weld Point, by means of the Four-Ball Extreme-Pressure (EP) Tester.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.1 and 7.2.

Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)

ASTM D2596-97 润滑脂极压性能的标准试验方法(四球法)

1.1 This test method covers the determination of the load-carrying properties of lubricating greases. Two determinations are made:1.1.1 Load-Wear Index (formerly called Mean-Hertz Load), and1.1.2 Weld Point, by means of the Four-Ball Extreme-Pressure (EP) Tester.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.1 and 7.2.

Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)

NF T60-102:1996 润滑脂.滴点测定

Lubricating greases. Determination of the dropping point.

BS 2000-132:1996 石油及其产品的试验方法 石油产品 润滑脂 滴点的测定

Identical with IP 132/96.

Methods of test for petroleum and its products. Petroleum products. Lubricating grease. Determination of dropping point

BS 2000-346:1996 石油和石油产品试验方法.第102部分:未用的润滑基油和不含沥青烯的石油馏分物中多环芳香族环烃的测定.二甲硫析取物折射指数法

Identical with IP 346/92(98).

Methods of test for petroleum and its products - Determination of polycyclic aromatics in unused lubricating base oils and asphaltene free petroleum fractions - Dimethyl sulphoxide extraction refractive index method

BS EN 10149-1:1996 冷成型用高屈服强度钢制热轧扁平产品.第1部分:一般交货条件

1 This European Standard specifies requirements for flat products made of weldable, hot-rolled, high yield strength alloy quality and special steels for cold forming. Part 1 of this European Standard specifies the general delivery conditions. Part 2 of this European Standard specifies the delivery conditions for thermomechanically rolled steels in the grades given in table 1 (chemical composition) and table 2 (mechanical properties) of Part 2. Part 3 of this European Standard specifies the delivery conditions for normalized or normalized rolled steels in the grades given in table 1 (chemical composition) and table 2 (mechanical properties) of Part 3. The steels specified in Part 2 and 3 of this European Standard are applicable to hot-rolled flat products in the thickness range of 1,5 mm to 20 mm for the steels with ReH ≤ 460 N/mm and 1,5 mm to 16 mm for the steels with higher minimum yield strength. 2 This European Standard does not apply to products for pressure vessels and products for which other EURONORMS exist or European Standards dealing with steels for general structural applications are being prepared: - Hot-rolled products of non-alloy structural steels - (see EN 10025); - Semi-finished products for forging in general purpose structural steel —(see EURONORM 30); - Weldable fine grain structural steels —(see EN 10113 Parts 1 - 3); - Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened condition —(see EN 10137 Parts 1 - 3); - Structural steels with improved atmospheric corrosion resistance —(see EN 10155); - Steels for shipbuilding —normal and high strength qualities —(see EURONORM 156); - Hot finished structural hollow sections (see EN 10210-1).

Specification for hot-rolled flat products made of high yield strength steels for cold forming - General delivery conditions

SAE AMS3084B-1996 最小限度除气的固态薄膜润滑剂

This specification covers a solid film lubricant in the form of a ready-to-use, sprayable suspension. This lubricant has been used typically in temperature environments ranging from -300 degrees to +750 degrees F (-184 degrees to +399 degrees C) and in space applications requiring minimal outgassing characteristics, but usage is not limited to such applications.

Lubricant, Solid Film Minimal Outgassing

ASTM D5969-96 在稀释合成海水的情况下测定润滑脂防腐蚀性能的标准试验方法

1.1 This test method covers the determination of the corrosion-preventive properties of greases using grease-lubricated tapered roller bearings exposed to various concentrations of dilute synthetic sea water stored under wet conditions. It is based on Test Method D 1743, which is practiced using a similar procedure and distilled water. The reported result is a pass or fail rating as determined by at least two of three bearings. 1.2 The values stated in acceptable inch-pound units for the apparatus dimensions are to be regarded as standard, and the SI conversions are provided for information only. All other values stated in acceptable SI units are standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of limitations prior to use.

Standard Test Method for Corrosion-Preventive Properties of Lubricating Greases in Presence of Dilute Synthetic Sea Water Environments

ASTM D3704-96(2006) 在摆动运动中使用法列克司环和块磨擦试验机测定润滑脂防磨性的标准试验方法

This test method is used to differentiate between greases having high, medium, and low wear preventive properties using oscillating motion. The user of this method should determine to his own satisfaction whether results of this test procedure correlate with field performance or other bench test machines.1.1 This test method covers the determination of wear properties of lubricating greases by means of the Falex block-on-ring friction and wear test machine.1.2 The values stated in SI units are to be regarded as standard except where equipment is supplied using inch-pound units and would then be regarded as standard. The metric equivalents of inch-pound units given in such cases in the body of the standard may be approximate.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use

Standard Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion

ASTM D3704-96(2012) 在摆动运动中使用(法列克司)环和块磨擦试验机测定润滑脂防磨性的标准试验方法

This test method is used to differentiate between greases having high, medium, and low wear preventive properties using oscillating motion. The user of this method should determine to his own satisfaction whether results of this test procedure correlate with field performance or other bench test machines.1.1 This test method covers the determination of wear properties of lubricating greases by means of the Falex block-on-ring friction and wear test machine. 1.2 The values stated in SI units are to be regarded as standard except where equipment is supplied using inch-pound units and would then be regarded as standard. The metric equivalents of inch-pound units given in such cases in the body of the standard may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use

Standard Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion

ASTM D1264-96 确定润滑脂水洗出性能的标准试验方法

1.1 This test method covers the evaluation of the resistance of a lubricating grease to washout by water from a bearing, when tested at 38 and 79oC (100 and 175oF) under the prescribed laboratory conditions. It is not to be considered the equivalent of service evaluation tests. This test method may not be suitable for some greases containing highly volatile components.1.2 The values state in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 6.3 and 7.1.

Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases

NF T60-189:1995 润滑脂.车轮轴承脂的渗漏趋势

Lubricating greases. Leakage tendencies of automotive wheel bearing greases.

SH/T 0391-1995 701防锈添加剂（油溶性石油磺酸钡）

701 antirust additive (oil-soluble barium petroleum sulfonate)

ISO 2176:1995 石油产品 润滑脂 滴点的测定

Cancels and replaces the first edition (1972). Specifies a method for the determination of the dropping point of lubricating grease.

Petroleum products - Lubricating grease - Determination of dropping point

ASTM D4281-95(2005)e1 石油和润滑脂(碳氟化物可提取的物质)的重量测定标准试验方法

A knowledge of the quantity of oil and grease present in a waste is helpful in overcoming difficulties in wastewater treatment plant operation, in determining plant efficiencies, and in controlling the subsequent discharge of these materials to receiving streams. When oils and greases are discharged in wastewater or treated effluents, they often cause surface films and shoreline deposits.1.1 These test methods cover the estimation of oil and grease in water and wastewater by a gravimetric determination of fluorocarbon extractable substances from an acidified sample. Also included in this estimation of oil and grease are any other compounds soluble in chlorofluorocarbon-113 and non-volatile under the conditions of test. 1.2 The following two test methods are included:SectionsTest Method A-Liquid-Liquid ExtractionTest Method B-Soxhlet Extraction 1.3 These test methods are applicable to natural waters and domestic wastewaters. They are also suitable for most industrial wastewaters, although certain wastes may yield low results because of the presence of either excessive concentrations of natural greases or synthetic or modified compounds that are not well recovered by these test methods.1.4 These test methods measure those groups of substance called oil and grease, whether soluble or insoluble, polar or non-polar, or biological or mineral in origin, to the extent these substances partition from the matrix into chlorofluorocarbon-113 and are not volatilized under conditions of the test. (See the Introduction and Section of these test methods.)1.5 Because these test methods include an acidification step prior to extraction, soluble metallic soaps are hydrolyzed and recovered as fatty acids in the extraction step.1.6 These test methods were fully validated by collaborative testing in reagent Type IV water. The information on precision may not apply to other waters. Note 1Refer to companion procedures (Test Method D 3921).1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 12.1, 13.2, 20.1, and 20.5.

Standard Test Method for Oil and Grease (Fluorocarbon Extractable Substances) by Gravimetric Determination

ASTM D3527-95 汽车轮轴承润滑脂寿命性能的标准试验方法

1.1 This test method covers a laboratory procedure for evaluating the high-temperature life performance of wheel bearing greases when tested under prescribed conditions. Note 1-Changes to this test method in the 1985 revision increased test severity. Results will not be comparable with data from earlier procedures. 1.2 The values stated in SI units, except apparatus dimensions, are to be regarded as the standard. Apparatus dimensions in inches are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Notes 2 through 5.

Standard Test Method for Life Performance of Automotive Wheel Bearing Grease

ASTM D5483-95 用压差扫描热量测定法测试润滑脂的氧化反应时间的标准试验方法

1.1 This test method covers the determination of oxidation induction time of lubricating greases subjected to oxygen at 3.5 MPa (500 psig) and temperatures between 155 and 210176;C.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Oxidation Induction Time of Lubricating Greases by Pressure Differential Scanning Calorimetry