E36 润滑脂 标准查询与下载

NF T60-199:1994 润滑脂 能够抵抗假布氏效应

Graisses lubrifiantes - Aptitude à résister au faux effet Brinell

SAE AMS3053-1994 防水合成烃基润滑脂

This specification covers a water resistant lubricant in the form of grease procured in inch/pound units. MAM 3053 is the metric version of this AMS. This grease has been used typically for lubrication of high speed main shaft bearings of missiles and turbine engines, but usage is not limited to such applications.

Grease, Water Resistant Polyalphaolefin Base

SH/T 0596-1994 润滑脂接触电阻测定法

Lubricating Grease Contact Resistance Determination Method

SH/T 0595-1994 7405号高温高压螺纹密封脂

No. 7405 high temperature and high pressure thread sealant

SH/T 0467-1994 4403号合成齿轮油

No. 4403 Synthetic Gear Oil

SH/T 0469-1994 7407号齿轮润滑脂

Gear Grease No. 7407

SH/T 0336-1994 润滑脂杂质含量测定法（显微镜法）

Determination method of grease impurity content (microscopic method)

SH/T 0587-1994 二硫化钼极压锂基润滑脂

Molybdenum disulfide extreme pressure lithium base grease

SH/T 0586-1994 L-CKC工业闭式齿轮油换油指标

L-CKC industrial closed gear oil change index

ASTM D2510-94(2012) 固态膜润滑剂粘附性的标准试验方法

Effective solid film lubricant coatings must adhere to surfaces to provide adequate lubrication in applications with restricted access where fluid lubricants cannot easily be replenished. Loss of coating adhesion results in metal to metal contact causing significant wear of contacting surfaces. Adhesion is critical to the performance of the solid film lubricant. Examples of solid film lubricant applications include fasteners, bearings and sliding members in automotive, aircraft, and aerospace hardware. This test method is intended to determine the adhesion of solid film lubricant coatings when submitted to contact with water and other fluids. Results of this test provide an indication of the suitability of the lubricant coating in applications where contact with water or other fluids is likely.1.1 This test method covers the measurement of the adhesion characteristics of dry solid film lubricants. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Adhesion of Solid Film Lubricants

ASTM D2265-94a 超宽温度范围润滑脂滴点的标准试验方法

1.1 This test method covers the determination of the dropping point of lubricating grease. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range

ASTM D3702-94(2014) 用止推垫圈试验机测定自润滑磨擦接触中材料磨损速率和摩擦系数的标准试验方法

4.1 This test method is used to determine the equilibrium rate of wear and coefficient of friction of materials in rubbing contact under useful operating conditions, that is, combinations of pressure and velocity that fall below the PV (pressure8201;×8201;velocity) limit of the test material. The user of this test method should determine to his own satisfaction whether the results of this test procedure correlate with field performance or other bench test machines. If the test conditions are changed, the wear rates may change and the relative value of one material with respect to another may also change. 4.2 Test conditions may be selected from Table 1. TABLE 1 Test ConditionsA Rotational speed, rpm Rubbing Velocity, ft/min (m/min) Load, lb (kg), to Obtain PV, psi8201;×8201;ft/min (kg/cm 28201;×8201;m/min) at Selected Speeds PV1 1250 (26.8) PV2 2500 (53.6) PV3 5000 (107.1)

Standard Test Method for Wear Rate and Coefficient of Friction of Materials in Self-Lubricated Rubbing Contact Using a Thrust Washer Testing Machine

ASTM D1743-94e1 润滑脂防腐蚀性能测定的标准试验方法

1.1 This test method covers the determination of the corrosion preventive properties of greases using grease-lubricated tapered roller bearings stored under wet conditions. This test method is based on CRC Technique L 41that shows correlations between laboratory results and service for grease lubricated aircraft wheel bearings. 1.2 The values stated in acceptable inch-pound units for the apparatus dimensions are to be regarded as standard, and the metric conversions are provided for information only. All other values stated in acceptable metric units are standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases

ASTM D1831-94e1 润滑脂滚轧稳定性的标准试验方法

1.1 This test method covers determination of the changes in the consistency, as measured by cone penetration, of lubricating greases when worked in the roll stability test apparatus.1.2 The values stated in inch-pound units for the apparatus dimensions are to be regarded as standard; the SI conversions are provided for information only. All other values stated in SI units are standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Roll Stability of Lubricating Grease

NF T60-191:1993 石油产品和润滑脂.润滑脂存储时的脱油现象.承压的静态条件

Petroleum products and lubricating greases. Oil separation on storage of grease. Static conditions under pressure.

IEC TR2 61221:1993 石油产品和润滑剂 三芳基磷酸酯涡轮机控制液(ISO-L-TCD类) 规范

Petroleum products and lubricants; triaryl phosphate ester turbine control fluids (category ISO-L-TCD); specifications

NF T60-132:1993 石油产品.润滑脂的锥入度和耐水性能

Petrolum products. Cone penetration and water resistance of lubricating greases.

BS 2000-142:1993 石油和石油产品的试验方法.润滑脂氧化稳定性的测定.氧弹法

Identical with IP 142/85(92).

Methods of test for petroleum and its products - Determination of oxidation stability of lubricating grease - Oxygen bomb method

BS 2000-50:1993 石油和石油产品的试验方法.润滑脂的锥入度测定

Identical with IP 50/88.

Methods of test for petroleum and its products. Determination of cone penetration of lubricating grease

SH/T 0535-1993 极压复合锂基润滑脂

Extreme pressure lithium complex grease