G38 胶粘剂基础标准与通用方法 标准查询与下载

ISO 16525-4:2014 粘合剂. 各向同性的导电粘合剂的试验方法. 第4部分: 硬料和硬料粘合组件使用中抗剪强度与抗电阻性的测定

This part of ISO 16525 specifies test methods using miniature specimens to determine shear strength and electrical resistance of a bonded joint that consists of isotropic electrically conductive adhesives and rigid adherends in specified conditions.

Adhesives - Test methods for isotropic electrically conductive adhesives - Part 4: Determination of shear strength and electrical resistance using rigid-to-rigid bonded assemblies

ISO 16525-7:2014 粘合剂. 各向同性的导电粘合剂的试验方法. 第7部分: 环境试验方法

This part of ISO 16525 specifies the environmental test methods (cold, dry heat, damp heat and change of temperature) for isotropic electrically conductive adhesives used in the surface assembly of printed circuit boards of electronic devices.

Adhesives - Test methods for isotropic electrically conductive adhesives - Part 7: Environmental test methods

ISO 16525-8:2014 粘合剂. 各向同性的导电粘合剂的试验方法. 第8部分: 电化学迁移试验方法

This part of ISO 16525 specifies test methods for confirming the occurrence of electrochemical migration in electrically isotropic conductive adhesives at high-temperature and humidity. The electrical resistance is also determined.

Adhesives - Test methods for isotropic electrically conductive adhesives - Part 8: Electrochemical-migration test methods

ISO 16525-5:2014 粘合剂. 各向同性的导电粘合剂的试验方法. 第5部分: 抗剪疲劳度的测定

This part of ISO 16525 specifies test methods using miniature specimens to measure shear fatigue of a glued joint that consists of isotropic electrically conductive adhesives and rigid adherends in specified conditions.

Adhesives - Test methods for isotropic electrically conductive adhesives - Part 5: Determination of shear fatigue

ISO 16525-3:2014 粘合剂. 各向同性的导电粘合剂的试验方法. 第3部分: 传热性能的测定

This part of ISO 16525 specifies test methods for heat-transfer properties such as effective thermal conductivity and thermal resistance by a steady-state comparative longitudinal heat-flow method (SCHF method) using cartridge-type specimen for isotropic electrically conductive adhesives used in wiring, die attach, and surface assembly.

Adhesives - Test methods for isotropic electrically conductive adhesives - Part 3: Determination of heat-transfer properties

BS EN 28510-1:2014 粘合剂. 软料与硬料粘合试样组件剥离试验. 90°剥离

Adhesives. Peel test for a flexible-bonded-to-rigid test specimen assembly. 90 peel

EN 28510-1:2014 粘合剂.软质与硬质粘合试样组件的剥离试验.第1部分:90°剥离

This part of EN 28510 specifies a 90° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where at least one adherend is flexible. If a normal tensile testing machine is used for the test, the peel angle will not be constant at exactly 90°. If a constant angle of exactly 90° is required, a roller peeling device is used (see 4.1). The 90° peel test is particularly suitable for use with less flexible adherends for which a 180° peel test is not suitable because the adherends crack, break or delaminate. A 180° peel test is described in EN ISO 8510-2.

Adhesives - Peel test for a flexible-bonded-to-rigid test specimen assembly - Part 1: 90? peel

DIN EN 13999-2:2014 粘合剂.使用后低溶剂或无溶剂粘合剂排放特性的测量用短期方法.第2部分:挥发性有机化合物的测定.德文版本EN 13999-2-2013

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 2: Determination of volatile organic compounds; German version EN 13999-2:2013

DIN EN 13999-1:2014 胶粘剂.使用后低溶剂或无溶剂胶粘剂放射特性快速测量方法.第1部分:通用规程.德文版本EN 13999-1-2013

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure; German version EN 13999-1:2013

ASTM C771-14 预制密封带受热老化后重量损失的标准试验方法

5.1 Preformed tape sealants are tacky, deformable solids that are used under compression between two substrates in a variety of sealing applications. Compared to other types of sealants, that is, gunnable sealants and caulks, sealing tapes are designed to be essentially 1008201;% solids materials. In use, these tapes are intended to give long service with minimal weight loss or volatility. This procedure will give a measure of the weight loss of a preformed tape sealant after a controlled period of exposure at an elevated temperature. 1.1 This test method covers a laboratory procedure for determining the weight loss after heat aging of preformed tape sealants. Note 1—Test Method C681 describes a weight loss or volatility test for knife-grade glazing compounds. 1.2 The values stated in acceptable metric units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Weight Loss After Heat Aging of Preformed Tape Sealants

KS M ISO 17212:2013 结构胶黏剂.粘接前金属和塑料表面处理导则

이 표준은 시험실 평가나 조립 절차 이전에 구성물의 표면을 준비하는 데 이용되는 절차에 대해 규정한다. 이 표준은 일반적으로 만나는 금속과 플라스틱 표면에 적용한다.

Structural adhesives -- Guidelines for the surface preparation of metals and plastics prior to adhesive bonding

KS M ISO 6238:2013 黏合剂.木材与木材黏合剂.用压缩负荷测定剪切强度

이 표준은 압축이 적용되는 표준 시료와 준비, 상태, 시험의 특정한 조건하에서 목재 대 목재 접착제의 전단 강도를 측정하는 방법에 대해 규정한다. 이 방법은 목재와 목재를 접합하는 데 사용되는 접착제에만 적용된다.

Adhesives — Wood-to-wood adhesive bonds-Determination of shear strength by compression loading

KS M ISO 6237:2013 黏合剂.木材与木材黏结体.用拉伸负荷测定剪切强度

이 표준은 인장이 적용되는 표준 시료와 준비, 상태, 실험의 특정한 조건 아래에서 목재 대 목재 접착제의 전단 강도를 측정하는 방법에 대해 규정한다. 이 방법은 평행한 얇은 판이거나 교차한 얇은판에서 목재 대 목재 접착에 사용된 접착제를 시험한 것에 대해서만 적용한다.

Adhesives — Wood-to-wood adhesive bonds–Determination of shear strength by tensile loading

BS EN 13999-1:2013 胶粘剂.低溶剂或无溶剂胶粘剂使用后排放特性的测量用短期方法.通用规程

Adhesives. Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application. General procedure

BS EN 13999-2:2013 胶粘剂.使用后低溶剂或无溶剂胶粘剂排放特性的快速测量方法.挥发性有机化合物的测定

Adhesives. Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application. Determination of volatile organic compounds

KS M ISO 15715:2013 涂料和清漆.水上和水下无腐蚀气体管道内侧的减小摩擦涂层

액체의 혼탁도 측정은 육안 또는 기기를 사용하여 수행할 수 있지만 육안 방법은 주관적이다. 이 표준은 액체 속의 불용성 물질에 의한 빛의 산란을 기기로 측정하여 혼탁도의 객관적 측정값을 얻는시험방법에 대하여 규정한다.액체상의 혼탁도는 불용성 물질(예를 들면 가라앉지 않는 응집물, 겔 또는 입자 또는 작은 방울 같은다른 현탁 물질)의 존재에 의해서 발생된다. 미세하게 분산된 불용성 물질의 경우에 혼탁도는 빛이액체를 통과해서 지나갈 때 입자에 의해서 산란된 빛의 강도를 측정함으로써 결정할 수 있다.이 표준은 투명 액체의 혼탁도를 측정하는 기기 방법에 대하여 규정한다. 이 표준은 투명도가 규정된 수지와 수지 용액, 용매, 투명한 도장 물질, 단량체와 다른 액체에 적용할 수 있다.

Binder for paints and varnishes — Determination for turbidity

NF T76-341:2013 胶粘剂 - 承载木结构用乳剂聚合异氰酸盐 (EPI) - 分类和性能要求

Adhesives - Emulsion polymerized isocyanate (EPI) for load-bearing timber structures - Classification and performance requirements

NF T76-409:2013 粘合剂.粘合镶木地板到底层地板的粘合剂.试验方法和最低要求

Adhesives - Adhesives for bonding parquet to subfloor - Test methods and minimum requirements

DIN EN 301:2013 承重木结构用酚醛和氨基塑料粘合剂. 分类和性能要求; 德文版本EN 301-2013

Adhesives, phenolic and aminoplastic, for load-bearing timber structures - Classification and performance requirements; German version EN 301:2013

SAE AMS3100D-2013 聚硫化物密封化合物用助粘剂

This specification covers adhesion promoters in the form of a liquid, either in bulk or aerosol form. This product has been typically used to enhance the adhesion of polysulfide sealing compounds or adhesives to AMS-C-27725 integral fuel tank coating, MIL-PRF-23377 epoxy primer, MIL-PRF-85582 waterborne primer, and bare titanium alloy substrates, but usage is not limited to such applications. Care should be exercised around plastic substrates (e.g. polycarbonates, acrylics) as the formulary solvents may tend to craze these surfaces. AMS3100 Class 2 may contain halogenated solvents that could cause stress-corrosion cracking when used on titanium alloys which

Adhesion Promoter For Polysulfide Sealing Compounds