G38 胶粘剂基础标准与通用方法 标准查询与下载

NF T76-152-1*NF EN 302-1:2013 承重木构件用粘接材料.试验方法.第1部分:纵向拉伸剪切强度中粘结强度的测定

Adhesives for load-bearing timber structures - Test methods - Part 1: determination of longitudinal tensile shear strength

DIN EN 1242:2013 粘合剂. 异氰酸盐含量的测定; 德文版本EN 1242-2013

Adhesives - Determination of isocyanate content; German version EN 1242:2013

BS EN 302-5:2013 承重结构用粘合剂. 基准条件下最大组合时间的测定

Adhesives for load-bearing structures. Determination of maximum assembly time under referenced conditions

BS EN 302-2:2013 承重木结构用粘合剂.试验方法.抗剥离性测定

Adhesives for load-bearing timber structures. Test methods. Determination of resistance to delamination

BS EN 302-3:2013 承重木结构用胶粘剂.试验方法.通过温度和湿度循环试验测定木纤维酸性腐蚀对横向拉伸强度的影响

Adhesives for load-bearing timber structures. Test methods. Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength

BS EN 302-6:2013 承重木结构用胶粘剂.试验方法.标准条件下最小加压时间的测定

Adhesives for load-bearing timber structures. Test methods. Determination of the minimum pressing time under referenced conditions

ISO 17178:2013 粘合剂.粘合镶木地板到底层地板的粘合剂.试验方法和最低要求

This International Standard specifies test methods for adhesives for bonding parquet and similar wood floorings to a subfloor. It also specifies the minimum requirements for shear strength, tensile strength to be achieved with these adhesives. This International Standard does not refer to the selection and installation of parquet floorings.

Adhesives - Adhesives for bonding parquet to subfloor - Test methods and minimum requirements

DIN EN 828:2013 胶粘剂. 润湿性. 固体表面接触角和表面自由能测定; 德文版本EN 828-2013

Adhesives - Wettability - Determination by measurement of contact angle and surface free energy of solid surface; German version EN 828:2013

BS EN 1242:2013 胶粘剂.异氰酸酯含量的测定

Adhesives. Determination of isocyanate content

EN 302-7:2013 承重木结构用粘合剂.试验方法.第7部分:基准条件下工作寿命的测定

This European Standard specifies a method for determining the working life for adhesives mixed with hardener for load-bearing timber structures, by a viscosity test. This method is not suitable for determining the working life of a multi-component adhesive whose actual working life is very short. This document is only intended for obtaining a reliable basis for comparison between adhesives. The method gives results which cannot be applied to the safe manufacture of timber structures without modifications for the influences of factory temperature and relative air humidity.

Adhesives for load-bearing timber structures - Test methods - Part 7: Determination of the working life under referenced conditions

EN 302-5:2013 承重结构用粘合剂.试验方法.第5部分:基准条件下最大组合时间的测定

This European Standard specifies a laboratory method of determining the maximum assembly time at two spread rate levels in standard atmosphere [20/65]. This European Standard is intended for obtaining a reliable base of comparison of the maximum assembly time between adhesives at referenced conditions.

Adhesives for load-bearing structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions

SN/T 3525-2013 进出口建筑用粘接剂中苯乙烯的测定.气相色谱-质谱法

本标准规定了进出口建筑用粘接剂中苯乙烯的气相色谱-质谱检测方法。本标准适用于进出口建筑用粘接剂中苯乙烯含量的测定。方法的测定低限为25 mg/kg。

Determination of styrene in adhesives used in buiding for import and export.Gas chromatography-mass spectrometry

EN 302-1:2013 承重木结构胶接.试验方法.第1部分:纵向拉伸剪切粘接强度测定

This European Standard specifies a method for determining the shear strength of adhesive bonds in close contact glue line and thick glue line. It is suitable for the following applications: a) for assessing the compliance of adhesives with EN 301, EN 15425 and prEN 16254; b) for assessing the suitability and quality of adhesives for load-bearing timber structures. This test is intended primarily to obtain performance data for the classification of adhesives for load-bearing timber structures according to their suitability for use in defined climatic environments. This method is not intended for use to provide for structural design, and does not necessarily represent the performance of the bonded member in service.

Adhesives for load-bearing timber structures - Test methods - Part 1: Determination of longitudinal tensile shear strength

EN 302-6:2013 承重木结构用粘合剂 试验方法 第6部分：参考条件下最小压制时间的测定

This European Standard specifies a method of determining the minimum pressing time for two glue line thicknesses, close contact glue line and 0,3 mm thick glue line (for gap filling adhesive 1,0 mm), at three temperatures. It is applicable to adhesives used in load-bearing timber structures. This European Standard is only intended for obtaining a reliable base of comparison of pressing time between adhesives. The method gives results that cannot be applied to the safe manufacture of timber structures without modifications for the influences of timber density/absorbency, moisture content, factory temperature and relative air humidity.

Adhesives for load-bearing timber structures - Test methods - Part 6: Determination of the minimum pressing time under referenced conditions

DIN 54458:2013 结构胶粘剂. 采用振荡流变测量法测定粘弹性胶粘剂流动性和应用表现

Structural adhesives - Determination of the flowability and application behaviour of viscoelastic adhesives using the oscillation rheometry

NF T76-150*NF EN 828:2013 粘合剂. 亲水性. 通过测量固体表面接触角度和表面自由能的测定

Adhesives - Wettability - Determination by measurement of contact angle and surface free energy of solid surface

BS EN 828:2013 胶粘剂. 润湿性. 固体表面接触角和表面自由能测定

Adhesives. Wettability. Determination by measurement of contact angle and surface free energy of solid surface

ANSI 405-2013 胶合木结构中用粘合剂标准

Standard for Adhesives for Use in Structural Glued Laminated Timber

ANSI A118.3-2013 耐化学药品水可清洁瓷砖安装和灌浆环氧树脂和水可清洁瓷砖设置安装环氧胶粘剂的标准规格

Standard Specification for Chemical Resistance, Water Cleanable Tile-Setting and -Grouting Epoxy and Water Cleanabel Tile-Setting Epoxy Adhesive

ASTM D297-13 使用倒置探头机测定胶粘剂压合粘结性的标准试验方法

1.1 These test methods cover the qualitative and quantitative analysis of the composition of rubber products of the “R” family (see 3.1). Many of these test methods may be applied to the analysis of natural and synthetic crude rubbers. 1.1.1 Part A consists of general test methods for use in the determination of some or all of the major constituents of a rubber product. 1.1.2 Part B covers the determination of specific polymers present in a rubber product. 1.1.3 The test methods appear in the following order: Part A. General Test Methods: Sections Rubber Polymer Content by the Indirect Method 11-13 Determinations and Report for the General Method 14 and 15 Density 16 Extract Analysis 17-26 Sulfur Analysis

Standard Test Methods for Rubber Productsmdash;Chemical Analysis