G38 胶粘剂基础标准与通用方法 标准查询与下载

KS M 3833-2012 压力管聚丙烯(PP)共聚物配件.热熔接的管接口.米制系列.接口尺寸

이 표준은 압력하에 유체를 이송하는 데에 사용하는 PP관을 융착 접합하는 소켓(이하 소켓이

Polypropylene(PP) fittings for pipes under pressure-sockets for fusion using heated tools-metric series-dimensions of sockets

ASTM D2559-12a 室外暴露条件中层压结构木制品用胶粘剂的标准规格

1.1 This specification covers adhesives suitable for the bonding of wood, including treated wood, into structural wood products for general construction or other uses where a high-strength, durable adhesive bond is required. 1.2 This specification includes test methods that may be referenced by specific product standards for the evaluation and approval of structural wood adhesives. Methods are included to evaluate adhesives intended for use in exterior exposure. Note 18212;Consult the Commentary in Appendix X1 regarding the intent and limitations of each test method contained in this specification. 1.3 Description of Bondline Performance8212;It is recognized that structural wood adhesives are used in various applications and levels of severity in terms of moisture content, loading, cyclic and seasonal weather conditions, heat exposure and other use conditions. It is the intent of this standard to determine the suitability of an adhesive for use under various levels of severity and conditions with specific and appropriate test methods and requirements. Note 28212;This specification does not contain specific tests outlined for different chemical types of adhesives. 1.4 Strength and durability requirements of the adhesive in Service Class A are based on the performance of the adhesive in laminated wood as measured by: 1.4.1 Resistance to shear by compression loading after conditioning to the target moisture content indicated in 14.2.3 and meeting requirements in 14.4. 1.4.2 Resistance to delamination during exposure to three cycles of vacuum pressure wetting followed by drying at elevated temperature as indicated in 15.3 and meeting requirements in 15.4. 1.4.3 Resistance to creep under static load by subjecting test specimens to a specified shear stress and exposing one set of test specimens to an environment of elevated temperature and ambient humidity and another set to an environment of high humidity and meeting requirements set forth in 16.3. 1.4.4 For applications involving chemical treatment, the adhesive shall be evaluated using representative samples of treated wood. Note 38212;When using chemically treated wood, compatibility between the treatment, adhesive, and wood is to be considered and agreed upon between the chemical manufacture and the user. Note 48212;Additional durability testing may also be required as specified by individual product standards. Consult the Commentary in Appendix X1 for additional information and guidance as to the type of durability testing that may be appropriate to supplement this specification when characterizing the adhesive for suitability with specific wood products. 1.5 The evaluation of adhesives for use in ground contact and marine exposures are beyond the scope of this specification. 1.6 The evaluation of binder adhesives is beyond the scope of this specification. 1.7 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.8 The text of this specification references notes, footnotes and a commentary which provide explanatory material. These notes, footnotes and commentary (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro......

Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions

ASTM D907-12a 胶粘剂标准术语

1.1 This terminology standard is a compilation of definitions used in the science and technology of the adhesives industry. Terms that are generally understood or adequately defined in other readily available sources are not included. 1.2 Any changes in this standard since 1988 are documented as follows: 1.2.1 Appendix X1 gives a history of revisions made since 1988. Table X1.1 lists the terms that are affected as: (1) Terms Added, (2) Terms Revised, and (3) Terms Deleted. 1.2.1.1 In Table X1.1, the year of publication in Volume 15.06 is shown in parentheses following the term. 1.2.2 In the text of the standard, the year of publication is shown following each definition. Also, the following codes are included after the year of publication to describe the type change that was made: (A) Addition, (R) Revision, or (E) Edited. 1.2.3 Deletions are shown in Appendix X1, suitably footnoted. The deleted terms do not appear in the text of the standard. 1.2.4 Any special circumstances not covered by 1.2.2 and 1.2.3 are documented in Table X1.1, suitably footnoted.

Standard Terminology of Adhesives

ASTM C882/C882M-12 斜切法测定混凝土用环氧树脂粘结剂的粘结强度的标准试验方法

The strength developed by a bonding system that joins two regions of concrete is its most important property.1.1 This test method covers the determination of the bond strength of epoxy-resin-base bonding systems for use with portland-cement concrete. This test method covers bonding hardened concrete to hardened or freshly-mixed concrete. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazard statement is given in Section 8. (WarningFresh hydraulic cementitious mixtures are caustic and may cause chemical burns to exposed skin and tissue upon prolonged exposure. )

Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete By Slant Shear

ASTM D907-12 胶粘剂标准术语

1.1 This terminology standard is a compilation of definitions used in the science and technology of the adhesives industry. Terms that are generally understood or adequately defined in other readily available sources are not included. 1.2 Any changes in this standard since 1988 are documented as follows: 1.2.1 Appendix X1 gives a history of revisions made since 1988. Table X1.1 lists the terms that are affected as: (1) Terms Added, (2) Terms Revised, and (3) Terms Deleted. 1.2.1.1 In Table X1.1, the year of publication in Volume 15.06 is shown in parentheses following the term. 1.2.2 In the text of the standard, the year of publication is shown following each definition. Also, the following codes are included after the year of publication to describe the type change that was made: (A) Addition, (R) Revision, or (E) Edited. 1.2.3 Deletions are shown in Appendix X1, suitably footnoted. The deleted terms do not appear in the text of the standard. 1.2.4 Any special circumstances not covered by 1.2.2 and 1.2.3 are documented in Table X1.1, suitably footnoted.

Standard Terminology of Adhesives

ASTM D2564-12 聚氯乙烯(PVC)塑料管道系统用液态粘结剂的的标准规格

1.1 This specification covers requirements for poly(vinyl chloride) (PVC) solvent cements to be used in joining poly(vinyl chloride) piping systems. 1.2 These solvent cements are used with poly(vinyl chloride) piping systems made from compounds as defined in Specification D1784. 1.3 A procedure for joining PVC pipe and fittings is given in Practice D2855. 1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems

ANSI/ASTM D2564:2012 聚氯乙烯(PVC)塑料管道系统用液状粘固剂规格

Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems

KS M 3811-2011 聚甲基丙烯酸甲酯板

이 표준은 메타크릴 수지판(이하 판이라 한다.)에 대하여 규정한다. 다만, 항공기용, X선

Polymethyl methacrylate sheets

KS M 3729-2011 胶黏剂剪切冲击强度试验方法

이 표준은 접착제의 충격 접착 강도 시험방법에 대하여 규정한다.

Testing methods for impact shear strength of adhesive bonds

KS M 3728-2011 胶黏剂劈裂强度试验方法

이 표준은 접착제의 쪼갬 접착 강도 시험방법에 대하여 규정한다.

Testing methods for cleavage strength of adhesive bonds

KS M 3726-2011 黏合剂.溶于水与碱性溶液的压敏胶可溶性测量

이 표준은 물에 녹는 감압 접착제의 수용성과 알칼리에 녹는 감압 접착제의 알칼리 가용성을

Adhesives-Determination of solubility of water or alkali soluble pressure sensitive adhesives

KS M 3732-2011 黏合剂蠕变断裂的试验方法

이 표준은 일정 온도에서 접착 시험편에 장시간 정하중을 가한 경우, 접착제의 크리프 파괴

Testing methods for creep rupture of adhesive bonds

KS M 3820-2011 环氧树脂和固化剂试验方法通则

이 표준은 에폭시 수지 및 그 경화제에 대하여 시험에 공통되는 시험항목, 시험방법 및 일반

General rules for testing methods of epoxide resins and hardeners

KS M 3731-2011 黏合剂耐化学物质腐蚀性试验方法

이 표준은 접착제의 내약품성을 정해진 방법으로 제작된 표준 접착 강도 시험편으로 측정하는

Testing methods for resistance of adhesive bonds to chemical substances

KS M 3734-2011 用拉伸负荷测定黏合剂剪切强度

이 표준은 접착제의 인장 전단 접착 강도 시험방법에 대하여 규정한다.

Testing methods for shear strength of adhesives bonds by tensile loading

KS M 3730-2011 黏合剂耐水性试验方法

이 표준은 접착제의 내수성 및 내습성을 정해진 방법으로 제작한 표준 접착 강도 시험편에 의

Testing methods for resistance of adhesive bonds to water or moisture

KS M 3705-2011 黏合剂普通试验方法

이 표준은 접착제의 일반적인 시험 항목에 관한 시험방법에 대하여 규정한다.

General testing methods for adhesives

KS M 3814-2011 工业用硝基漆

이 표준은 일반 산업용(셀룰로이드용 및 화약용의 나이트로셀룰로오스는 제외한다.)의 나이트로

Industrial nitrocellulose

DIN EN ISO 9311-2:2011 热塑性管道系统的粘合剂.第2部分:剪切强度的测定(ISO9311-2-2011).德文版EN ISO 9311-2-2011

Adhesives for thermoplastic piping systems - Part 2: Determination of shear strength (ISO 9311-2:2011); German version EN ISO 9311-2:2011

BS EN ISO 9311-2:2011 热塑性管道系统用粘合剂.剪切强度测定

SAFETY PRECAUTIONS — Persons using this document should be familiar with the normal laboratory practice, if applicable. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. CAUTION — It is understood that some of the material permitted in this standard may have negative environmental impact. As technological advantages lead to acceptable alternatives for these materials, they will be eliminated from this standard to the extent possible. At the end of the test, the user of the standard shall take care to carry out an appropriate disposal of the wastes, according to local regulation. This part of ISO 9311 specifies a method for the determination of the shear strength of joints made with adhesives for thermoplastic piping systems.

Adhesives for thermoplastic piping systems. Determination of shear strength