共找到 402 条与 橡胶密封件 相关的标准,共 27 页
Joints rings used for gaz supply pipes and fittings. Specification for material.
Specifies requirements, but does not apply to the mentioned product with an aromatic content higher than 30 % and liquids polluted by petroleum traces. Other requirements shall be specified in national standards. Iron, steel, copper, plastics are included as pipeline materials. Not included are joint rings made of cellular rubbers. 2 tables with general and optional requirements.
Rubber seals; Joint rings used for petroleum product supply pipes and fittings; Specification for material
1.1 This specification covers gaskets cut from sheet rubber that are intended for general gasket applications on water, air, and low-pressure steam. They are not intended for use with oils and strong acids. 1.2 The values stated in SI units are to be regarded as the standard.
Standard Specification for Rubber Sheet Gaskets
Rubber packing sheet for food containers
Rubber packing ring for food containers
Rubber sealing ring for Pressure cooker
Rubber packing sheet for food containers
Rubber packing ring for food containers
Rubber sealing ring for Pressure cooker
Sheets of elastomers for waterproofing; terms of delivery
Sheets of elastomers for waterproofing; terms of delivery
Specification refers to operating temperatures up to 50 鳦. Other requirements, particularly functional tests for the actual sealing materials, shall be specified in national standards. Applicable to joint rings for all pipeline materials including iron, steel, copper, plastics. The standard does not include joint rings made from cellular rubbers or with enclosed voids. 2 tables with general and optional requirements.
Rubber seals; Joint rings used for gas supply pipes and fittings; Specification for material
本标准适用于活动密封。适用工作条件(介质、温度、压力)决定于被包复胶料的性能。
Technical conditions of "O" type rubber sealing ring coated with fluoroplastic
Non cellular elastomer glazing and panel gaskets; technical delivery conditionsZusammenhang mit den von der International Organization for Standardization (ISO) herausgegebenen Internationalen Normen ISO 3934-1978 und ISO 5892-1981, siehe Erl?uterungen.
Non cellular elastomer glazing and panel gaskets; technical delivery conditions
These tests are used quantitatively, for evaluation, approval, and as a referee method. Also these tests are used qualitatively for quality control purposes.1.1 This specification covers the strength and appearance of the splice in vulcanized rubber-seal material of any size, type, or cross-sectional shape. 1.2 Many types and varieties of seals are used in services of all degrees of severity. In some instances, hollow tubing is spliced and used as a seal. It is also possible to have seals of irregular cross sections, or made of polymers which, due to their nature, or not conducive to a high-strength splice, although they will perform satisfactorily in their intended application. 1.3 Seals are exposed in service to a wide variety of media at various temperatures. The effect of such media on the spliced area must be considered. Details of the test procedures to evaluate the effect of the media shall be agreed upon by the purchaser and seller as part of the purchase contract. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Rubber Sealsmdash;Splice Strength
1.1 This specification covers the strength and appearance of the splice in vulcanized rubber-seal material of any size, type, or cross-sectional shape.1.2 Many types and varieties of seals are used in services of all degrees of severity. In some instances, hollow tubing is spliced and used as a seal. It is also possible to have seals of irregular cross sections, or made of polymers which, due to their nature, or not conducive to a high-strength splice, although they will perform satisfactorily in their intended application.1.3 Seals are exposed in service to a wide variety of media at various temperatures. The effect of such media on the spliced area must be considered. Details of the test procedures to evaluate the effect of the media shall be agreed upon by the purchaser and seller as part of the purchase contract.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Rubber Seals8212;Splice Strength
This handbook was developed by the Army Materiais and Mechanics ResearchCenter, in accordance with established procedures.
GUIDE TO THE SELECTION OF RUBBER O-RINGS
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号