G75 催化剂 标准查询与下载

HG/T 2086-2013 二氧化硫氧化制硫酸催化剂

本标准规定了 S101、S101-2H、S107、S108、S107-1H、S108-1H、S109(S109-1、S109-2)型等二氧化硫氧化制硫酸催化剂的要求,试验方法,检验规则和标志、包装、储存、运输。本标准适用于接触法硫酸生产过程中将二氧化硫氧化为三氧化硫用的S101、S101-2H、S107、S108、S107-1H、S108-1H、S109型等二氧化硫氧化制硫酸催化剂。

The catalyst oxidizing sulphuric dioxide into sulphuric acid

HG/T 2273.1-2013 天然气一段转化催化剂

本标准规定了 Z102、Z107、Z108、Z109-1Y、Z109-2Y、Z110Y、Z111型天然气一段转化催化剂的要求,试验方法,检验规则及标志、包装、储存、运输。本标准适用于合成氨、甲醇及制氢工业中以天然气、水蒸气为原料制取合成气(CO+H)和氢气装置使用的Z102、Z107、Z108、Z109-1Y、Z109-2Y、Z110Y、Z111型天然气一段转化催化剂及其同类型产品。

The natural gas catalyst for primary reforming

HG/T 2273.3-2013 天然气二段转化热保护剂

本标准规定了 Z205型天然气二段转化热保护剂的要求,试验方法,检验规则及标志、包装、储存、运输。本标准适用于合成氨厂二段转化炉中天然气进一步转化制取氢气装置中与天然气二段转化催化剂配套使用的Z205型天然气二段转化热保护剂及其同类型产品。

The heat resistant catalyst of natural gas for secondary reforming

HG/T 3550-2013 氨合成催化剂

本标准规定了 A110 系列(包括 A110-1、A110-2、A110-3、A110-4、A110-5Q、A110-6)、A201、A202、A203、A207、A301型等氨合成催化剂的要求、试验方法、检验规则和标志、包装、储存、运输。本标准适用于氨合成装置中,氢和氮反应制取氨用的A110系列(包括A110-1、A110-2、A110-3、A110-4、A110-5Q、A110-6)、A201、A202、A203、A207、A301 型氨合成催化剂。

Ammonia synthesis catalyst

HG/T 4556-2013 环己醇脱氢催化剂

本标准规定了环己醇脱氢制环己酮催化剂的要求、试验方法、检验规则以及标志、包装、储存、运输。本标准适用于大、中型环己酮生产装置中环己醇脱氢制环己酮用的铜系环己醇脱氢催化剂。

The catalyst for cyclohexanol dehydrogenation

HG/T 4557-2013 硝基苯加氢制苯胺催化剂

本标准规定了硝基苯加氢制苯胺催化剂的要求、试验方法、检验规则和标志、包装、储存、运输。本标准适用于流化床用硝基苯加氢制苯胺催化剂。

The catalyst for nitrobenzene hydrogenation to aniline

ASTM D3907/D3907M-13 使用微活性试验法测试流化床催化裂化(FCC)催化剂的标准试验方法

5.1 The microactivity test provides data to assess the relative performance of FCC catalyst. Because results are affected by catalyst pretreatment, feedstock characteristics, test equipment, and operating parameters, adherence to this test method is a prerequisite for correct interpretation of results. Apparatus, test conditions, and analytical procedures actually used should closely resemble those described in this test method. 5.2 Caution should be used in interpreting results above 80 weight % conversion due to the significance of overcracking. 1.1 This test method covers determining the activity of equilibrium or laboratory-deactivated fluid catalytic cracking (FCC) catalysts, or both. This is evaluated on the basis of weight percent conversion of gas oil in a microactivity unit. The selectivity of FCC catalysts can be determined using Test Method D5154. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Testing Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test

HG/T 2505-2012 有机硫加氢催化剂

本标准规定了T 201、T 203型有机硫加氢催化剂的要求、试验方法、检验规则和标志、包装、储存、运输。本标准适用于合成氨、制氢和合成甲醇原料气(油)中有机硫加氢的T 201、T 203型有机硫加氢催化剂以及同类有机硫加氢催化剂。

Organic sulphur hydrogenation catalysts

HG/T 4347-2012 轻油蒸汽转化催化剂

本标准规定了轻油蒸汽转化催化剂的要求、试验方法、检验规则和标志、包装、储存、运输。本标准适用于以石脑油、炼厂气、液态烃等为原料的轻油蒸汽转化催化剂。

Naphtha steam reforming catalysts

HG/T 4349-2012 常温氧硫化碳水解催化剂

本标准规定了常温氧硫化碳水解催化剂的要求、试验方法、检验规则以及标志、包装、储存和运输。本标准适用于合成氨、制氢、合成甲醇、有机合成原料气以及天然气中脱除氧硫化碳的常温氧硫化碳水解催化剂。

Carbonyl sulfide hydrolyzed catalysts at room temperature

HG/T 4351-2012 甲醇制备甲醛用电解银催化剂

本标准规定了甲醇制备甲醛用电解银催化剂的要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于甲醇制备甲醛,也适用于乙醇制备乙醛、乙二醇制备乙二醛等所用电解银催化剂(以下简称为“催化剂”)。

Electrolytic silver catalysts for preparation of formaldehyde with methanol

HG/T 2508-2012 氧化锌脱硫剂

本标准规定了T302Q、T304-1、T305型氧化锌脱硫剂的要求、试验方法、检验规则和标志、包装、储存、运输。本标准适用于合成氨、制氢、合成甲醇、有机合成原料气(油)中脱除硫化氢和部分有机硫化物的T302Q、T304-1、T305型氧化锌脱硫剂及其同类型产品。

Zinc oxide desulphurizers

HG/T 3556-2012 一氧化碳低温变换催化剂

本标准规定了B202型、B204型、B206型、B207型等一氧化碳低温变换催化剂的要求、试验方法、检验规则和标志、包装、储存、运输。本标准适用于合成氨及制氢装置中一氧化碳加水蒸气制氢的B202型、B204型、B206型、B207型等一氧化碳低温变换催化剂。

Low temperature carbon monoxide shift catalysts

HG/T 2509-2012 甲烷化催化剂

本标准规定了J101、J105、J106Q型等甲烷化催化剂的要求、试验方法、检验规则及标志、包装、储存、运输。本标准适用于合成氨厂、甲醇厂和制氢系统装置内使气体中少量碳氧化物加氢生成甲烷的甲烷化催化剂。

Methanation catalysts

ASTM D4284-12 用压汞仪测定催化剂及催化剂载体的孔隙体积分布的标准试验方法

This test method is intended to determine the volume distribution of pores in catalysts and catalyst carriers with respect to the apparent diameter of the entrances to the pores. In general, both the size and volume of pores in a catalyst affect its performance. Thus, the pore volume distribution is useful in understanding a catalyst's performance and in specifying a catalyst that can be expected to perform in a desired manner.1.1 This test method covers the determination of the pore volume distributions of catalysts and catalyst carriers by the method of mercury intrusion porosimetry. The range of apparent diameters of pores for which it is applicable is fixed by the operant pressure range of the testing instrument. This range is typically between apparent pore entrance diameters of about 100 and 0.003 μm (3 nm). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard information is given in Section 8.

Standard Test Method for Determining Pore Volume Distribution of Catalysts and Catalyst Carriers by Mercury Intrusion Porosimetry

HG/T 3546-2011 一氧化碳高温变换催化剂

本标准规定了B107、B107-1、B108、B109、B110-2、B111、B112、B113、B113-2、B116、B117、B118型等一氧化碳高温变换催化剂的要求、试验方法、检验规则和标志、包装、贮存、运输。 本标准适用于合成氨及制氢等装置中一氧化碳加水蒸气制氢的B107、B107-1、B108、B109、B110-2、B111、B112、B113、B113-2、B116、B117、B118型等一氧化碳高温变换催化剂。

High temperature carbon monoxide shift catalysts

HG/T 4192-2011 氯乙烯合成用低汞触媒

本标准规定了氯乙烯合成用低汞触媒的技术要求、试验方法及检验规则、标志、包装、运输、贮存、安全等。 本标准适用于以氯化汞为活性组分，活性炭为载体生产的氯乙烯合成用低汞触媒。

Low-level mercury catalyst for chloroethylene synthesis

DB34/T 1442-2011 FD型加氢脱硫催化剂

本标准适用于石油化工行业中催化汽油、直馏汽油、焦化汽油、裂解汽油加氢脱硫工艺用的加氢脱硫催化剂，天然气、石油液化等产品的加氢脱硫催化剂也可参照使用。

FD hydrodesulfurization catalyst

ASTM UOP333-10 筛析法测定催化剂和催化剂载体含量中的粉末

This method is for determining the fines content of catalysts or catalyst supports (spheres, extrudates, and trilobes) by screening through appropriate USA Standard Series testing sieves.

Fines in Catalysts and Catalyst Supports by Sieve Analysis

HG/T 2779-2009 一氧化碳耐硫变换催化剂(低压部分)

本标准规定了一氧化碳耐硫变换催化剂(低压部分)的要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于工况压力小于3.0MPa的合成氨及制氢等装置中，使用的一氧化碳加水蒸气制氢的一氧化碳耐硫变换催化剂。

Sulfur-tolerant carbon monoxide shift catalysts(low pressure part)