H20 金属理化性能试验方法综合 标准查询与下载

JIS Z 2280:1993 高温下金属材料的扬式模量试验方法

この規格は，金属材料の高温における動的及び静的ヤング率の試験方法について規定する。

Test method for Young's modulus of metallic materials at elevated temperature

ASTM E1561-93(2009) 应变片花数据分析的标准规范

1.1 The two primary uses of three-element strain gage rosettes are (a) to determine the directions and magnitudes of the principal surface strains and (b) to determine residual stresses. Residual stresses are treated in a separate ASTM standard, Test Method E 837. This practice defines a reference axis for each of the two principal types of rosette configurations used and presents equations for data analysis. This is important for consistency in reporting results and for avoiding ambiguity in data analysis—especially when computers are used. There are several possible sets of equations, but the set presented here is perhaps the most common.

Standard Practice for Analysis of Strain Gage Rosette Data

ASTM E1561-93(2003) 应变片花数据分析标准规范

1.1 The two primary uses of three-element strain gage rosettes are (a) to determine the directions and magnitudes of the principal surface strains and (b) to determine residual stresses. Residual stresses are treated in a separate ASTM standard, Test Method E837. This practice defines a reference axis for each of the two principal types of rosette configurations used and presents equations for data analysis. This is important for consistency in reporting results and for avoiding ambiguity in data analysis-especially when computers are used. There are several possible sets of equations, but the set presented here is perhaps the most common.

Standard Practice for Analysis of Strain Gage Rosette Data

NF A03-012:1992 金属材料.夏比冲击试验.第2部分:试验机的检定(摆锤冲击)

Metallic materials. Charpy impact test. Part 2 : verification of the testing machine (pendulum impact).

ISO 10215:1992 阳极氧化铝和铝合金 阳极氧化膜图像清晰度的目视测定 图表比例尺法

本标准规定了用条标片和明度标片目视测定阳极氧化膜表面影像清晰度的方法。 本标准仅适用于能反映条标影像的平滑表面。

Anodized aluminium and aluminium alloys; visual determination of image clarity of anodic oxidation coatings; chart scale method

ASTM E479-91(2006) 泄漏试验规格的准备

For any product to be tested the geometrical complexity will vary widely. However, the basic concept of determining an operative leakage specification regardless of geometries is much the same for all, whether it be simple, ordinary, or complex. The data required for writing the OS, which is total leakage (moles), time(s), and pressure difference across the leak, are either available or can be determined by tests or measurements. A user who selects values to be used in a leakage specification as a result of someone else having used the value or simply because of prestige reasons, may find the value or values unsatisfactory for the product. A specification that is too restrictive may result in excessive leak testing costs. A specification that is not restrictive enough may result in premature product failure, or increased warranty costs, or both. A typical illustration for determining a leakage specification, using the complex geometry of a refrigerant system for an example, will be used throughout this recommended guide. It is well to point out that the user should realize that the values and test methods selected do not necessarily represent the best or typical ones for this application.1.1 This standard is intended as a guide. It enumerates factors to be considered in preparing a definitive specification for maximum permissible gas leakage of a component, device, or system. The guide relates and provides examples of data for the preparation of leak testing specifications. It is primarily applicable for use in specifying halogen leak testing methods.1.2 Two types of specifications are described:1.2.1 Operational specifications (OS), and1.2.2 Testing specifications (TS):Total, andEach leak.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Preparation of a Leak Testing Specification

ISO 8044:1989 金属和合金的耐腐蚀性.词汇

Corrosion of metals and alloys; vocabulary

ISO/TR 10108:1989 钢 硬度值与抗拉强度值的换算

Describes the bands for conversion of hardness to tensile strength established to hardness scales of Brinell and Vickers as well as rules for their use. Applies to any steel but only to products in full section (thickness over 2 mm).

Steel; conversion of hardness values to tensile strength values

HB 5433-1989 金属材料的销型支承试验方法

本标准规定了金属材料的销型支承试验方法和对试验条件要求。 　　本标准适用于室温〔G1〕条件下，测定金属板材的支承屈服强度和断裂强度。

Test method for pin bearings of metallic materials

JIS H 7101:1989 成型记忆合金相变点的测定方法

Method for determining the transformation temperatures of shape memory alloys

ISO 7373:1987 铁合金 检验样品缩分精度的试验方法

The methods are carried out on the gross sample or sub-sample obtained from a ferroalloy consignment according to the methods prescribed in the relevant International Standard. The methods are applicable to the taking of increments of crushable ferroalloys but are not applicable to uncrushable ferroalloys of which increments are taken by boring.

Ferroalloys; Experimental methods for checking the precision of sample division

ISO 7347:1987 铁合金 检验取样和样品制备偏差的试验方法

Applies to ferroalloys given in the relevant International Standards. Should be read in conjunction with ISO 3713, ISO 7087 and ISO 7373. Includes four annexes.

Ferroalloys; Experimental methods for checking the bias of sampling and sample preparation

ISO 7539-1:1987 金属与合金的腐蚀 应力腐蚀试验 第1部分:试验程序的通用指南

Descsribes the general considerations which apply when designing and conducting tests to assess susceptibility of metals to stress corrosion. Particular methods of test are not treated in detail in this document. These are specified in the additional parts of ISO 7539.

Corrosion of metals and alloys - Stress corrosion testing - Part 1: General guidance on testing procedures

ISO 7087:1984 铁合金 评估质量偏差的实验方法和检验取样精度的方法

Specifies methods for the purposes of determining the parameters of random sampling given in the relevant International Standards. Includes an annex.

Ferroalloys; Experimental methods for the evaluation of the quality variation and methods for checking the precision of sampling

BS 6285:1982 钢的硫印粗视组织检查法(鲍曼法)

Specifies the Baumann method for qualitative assessment of the position and quantity of sulphides present in steel.

Method for the macrographic examination of steel by sulphur print (Baumann method)

NF A04-111:1980 钢铁.非合金高碳钢线材脱碳深度的显微照相法测定

Iron and steel. Micrographic determination of the extent of decarburisation of non alloy high carbon steel wire rod.

HB 5057-1977 铝及铝合金硬质阳极氧化膜层质量检验

Aluminum and aluminum alloy hard anodic oxidation coating quality inspection

HB 5055-1977 铝及铝合金硫酸阳极氧化膜层质量检验

Quality inspection of sulfuric acid anodic oxidation film layer on aluminum and aluminum alloy

HB 5056-1977 铝及铝合金铬酸阳极氧化膜层质量检验（试行）

本标准规定了铝及铝合金铬酸阳极氧化膜层的质量和检验方法。 　　适用于航空产品铝及铝合金零（组）件铬酸阳极氧化膜层的质量验收。

Quality inspection of aluminum and aluminum alloy chromic acid anodic oxidation film layer (trial implementation)

HB 5063-1977 钢铁零件磷化膜层质量检验（试行）

本标准规定了钢铁零件磷化膜层的质量要求和检验方法。 　　适用于航空产品钢铁零（组）件磷化膜层的质量检验。

Quality inspection of phosphating film layer on iron and steel parts (trial implementation)