H20 金属理化性能试验方法综合 标准查询与下载

ASTM G141-03 非金属材料曝光测试中变异度表达的标准导则

Many standards and specifications reference exposure tests performed according to standards that are the responsibility of Committee G03 on Durability of Nonmetallic Materials. In many cases, use of the data generated in these tests fails to consider the ramifications of variability in the exposure test practices. This variability can have a profound effect on the interpretation of results from the exposure tests, and if not taken into consideration in test design and data analysis, can lead to erroneous or misleading conclusions. This guide lists some of the sources for test variability and recommends strategies for executing successful weathering studies. Not all sources of variability in weathering testing are addressed in this guide. Specific materials, sampling procedures, specimen preparation, specimen conditioning, and material property measurements can contribute significantly to variability in weathering test results. Many of these concerns are addressed in Guide G 147. To reduce the contribution of an instrumental method to test variability, it is essential to follow appropriate calibration procedures and ASTM standards associated with the particular property measurement. Additional sources of variability in test results are listed in Guide D 4853, along with methods for identifying probable causes.1.1 This guide covers information on sources of variability and strategies for its reduction in exposure testing, and for taking variability into consideration in the design, execution, and data analysis of both exterior and laboratory accelerated exposure tests. 1.2 The values stated in either inch-pound or SI units are to be regarded separately as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Addressing Variability in Exposure Testing on Nonmetallic Materials

KS D 0056-2002 粉末冶金术语

이 규격은 분말 야금에 관련된 용어의 정의를 규정한다(1). 분말 야금은 야금법의 한 종류

Powder metallurgy－Vocabulary

KS B ISO 1099:2002 金属材料.疲劳试验.轴向力控制法

이 규격은 인위적으로 유기된 응력 집중이 없는 시험편에 대하여 시행하는 축 하중 피로 시험

Metals－Axial load fatigue testing

KS B ISO 12737:2002 金属材料.平面变形断裂韧性的测定

이 규격은 노치를 가공한 뒤 예비 피로 균열을 생성시킨, 균질한 금속 재료의 시험편에 하중

Metallic materials-Determination of plane-strain fracture toughness

KS B ISO 1352:2002 金属材料.扭矩受控的疲劳试验

이 규격은 인위적으로 유기된 응력 집중이 없으며 5 mm에서 12.5 mm사이의 공칭 지름

Steel-Torsinal stress fatigue testing

KS B ISO 17671-2:2002 焊接.金属材料焊接的推荐.第2部分:铁素体钢的电弧焊接

이 국제 표준은 페라이트계 스테인리스강을 제외한 모든 종류의 페라이트 강(5. 참조)의 수

Welding-Recommendations for welding of metallic materials-Part 2:Arc welding of ferritic steels

KS D 0076-2002 阻尼钢板的振动衰减特性试验方法

이 규격은 제진 강판의 양단 자유 진동 및 일단 고정 진동에 대한 진동 감쇠 특성의 시험

Test methods for vibration-damping property in laminated damping steel sheets of constrained type

KS D 0065-2002 阻尼材料术语

이 규격은 주로 금속계 제진 재료에 관한 주된 용어 및 뜻에 대하여 규정한다.

Glossary of terms used in damping materials

KS D 0067-2002 超导体术语

이 규격은 초전도 재료에 관한 주된 용어 및 정의에 대하여 규정한다.

Glossary of terms relating to superconductors

KS D 0066-2002 氢容器合金术语

이 규격은 수소 저장 합금과 그 응용 분야에 주로 사용되는 용어 및 정의에 대하여 규정한다

Glossary of terms used in hydrogen absorbing alloys

KS B ISO 17671-1:2002 焊接.金属材料焊接的推荐.第1部分:电弧焊接通用指南

이 규격은 금속 재료인 모든 형상의 제품(예를 들어, cast, wrought, 압출 제품

Welding－Recommendations for welding of metallic materials－Part 1：General guidance for arc welding

KS B ISO 17671-3:2002 焊接.金属材料焊接的推荐.第3部分:不锈钢的电弧焊接

이 규격은 스테인리스강의 용융 용접에 대한 일반적인 사항에 대하여 규정한다.

Welding－Recommendations for welding of metallic materials－Part 3：Arc welding of stainless steels

KS B ISO 17671-4:2002 焊接.金属材料焊接的推荐.第4部分:铝和铝合金的电弧焊接

이 국제 표준은 알루미늄 단련재 및 주조재의 용접을 수동, 기계식 및 자동 용융 용접할 경

Welding-Recommendations for welding of metallic materials-Part 4:Arc welding of aluminium and aluminium alloys

JIS H 7101:2002 形状记忆合金相变温度的测定方法

この規格は,形状記憶合金の示差走査熱量測定による変態点測定方法について規定する。

Method for determining the transformation temperature of shape memory alloys

ASTM E1139-02 连续监测来自金属压力界面的声发射的标准实施规程

Acoustic emission examination of a structure requires application of a mechanical or thermal stimulus. In this case, the system operating conditions provide the stimulation. During operation of the pressurized system, AE from active discontinuities such as cracks or from other acoustic sources such as leakage of high-pressure, high-temperature fluids can be detected by an instrumentation system using sensors mounted on the structure. The sensors are acoustically coupled to the surface of the structure by means of a couplant material or pressure on the interface between the sensing device and the structure. This facilitates the transmission of acoustic energy to the sensor. When the sensors are excited by acoustic emission energy, they transform the mechanical excitations into electrical signals. The signals from a detected AE source are electronically conditioned and processed to produce information relative to source location and other parameters needed for AE source characterization and evaluation. AE monitoring on a continuous basis is a currently available method for continuous surveillance of a structure to assess its continued integrity. The use of AE monitoring in this context is to identify the existence and location of AE sources. Also, information is provided to facilitate estimating the significance of the detected AE source relative to continued pressure system operation. In addition to immediate evaluation of the AE sources, a permanent record of the total data collected (AE plus pressure system parameters measured) provides an archival record which can be re-evaluated.1.1 This practice provides guidelines for continuous monitoring of acoustic emission (AE) from metal pressure boundaries in industrial systems during operation. Examples are pressure vessels, piping, and other system components which serve to contain system pressure. Pressure boundaries other than metal, such as composites, are specifically not covered by this document.1.2 The functions of AE monitoring are to detect, locate, and characterize AE sources to provide data to evaluate their significance relative to pressure boundary integrity. These sources are those activated during system operation, that is, no special stimulus is applied to produce AE. Other methods of nondestructive testing (NDT) may be used, when the pressure boundary is accessible, to further evaluate or substantiate the significance of detected AE sources.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 6.

Standard Practice for Continuous Monitoring of Acoustic Emission from Metal Pressure Boundaries

EJ/T 1136-2001 轻水堆核电厂安全壳外供暖、通风、空调系统设计准则

Design criteria for HVAC systems located outside containment of LWR nuclear power plant

ASTM E1820-01 裂纹韧性测量的标准试验方法

1.1 This test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD. Toughness can be measured in the R-curve format or as a point value. The fracture toughness determined in accordance with this test method is for the opening mode (Mode I) of loading.1.2 The recommended specimens are single-edge bend, [SE(B)], compact, [C(T)], and disk-shaped compact, [DC(T)]. All specimens contain notches that are sharpened with fatigue cracks.1.2.1 Specimen dimensional (size) requirements vary according to the fracture toughness analysis applied. The guidelines are established through consideration of material toughness, material flow strength, and the individual qualification requirements of the toughness value per values sought.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1--Other standard methods for the determination of fracture toughness using the parameters K, J, and CTOD are contained in Test Methods E399, E813, E1152, E1290, and E1737. This test method was developed to provide a common method for determining all applicable toughness parameters from a single test.

Standard Test Method for Measurement of Fracture Toughness

ASTM G40-01 有关侵蚀和磨损的标准术语

1.1 The terms and their definitions given herein represent terminology relating to wear and erosion of solid bodies due to mechanical interactions such as occur with cavitation, impingement by liquid jets or drops or by solid particles, or relative motion against contacting solid surfaces or fluids. This scope interfaces with but generally excludes those processes where material loss is wholly or principally due to chemical action and other related technical fields, as, for instance, lubrication. 1.2 This terminology is not exhaustive; the absence of any particular term from this collection does not necessarily imply that its use within this scope is discouraged. However, the terms given herein are the recommended terms for the concepts they represent unless otherwise noted. 1.3 Certain general terms and definitions may be restricted and interpreted, if necessary, to make them particularly applicable to the scope as defined herein. 1.4 The purpose of this terminology is to encourage uniformity and accuracy in the description of test methods and devices and in the reporting of test results in relation to wear and erosion. Note 18212;All terms are listed alphabetically. When a subsidiary term is defined in conjuntion with the definition of a more generic term, and alphabetically-listed cross-reference is provided.

Standard Terminology Relating to Wear and Erosion

ASTM G144-01 用高温燃烧分析仪全碳分析法测定材料成分中残余物污染的标准试验方法

1.1 This test method covers the determination of residual contamination in an aqueous sample by the use of a total carbon ( TC) analyzer. When used in conjunction with Practice G 131 and G 136, this procedure may be used to determine the cleanliness of systems, components, and materials requiring a high level of cleanliness, such as oxygen systems. This procedure is applicable for aqueous-based cleaning and sampling methods only.1.2 This test method is not suitable for the evaluation of particulate contamination, or contaminants that are not soluble in or that do not form an emulsion with water.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Residual Contamination of Materials and Components by Total Carbon Analysis Using a High-Temperature Combustion Analyzer

ASTM A751-01 钢制品化学分析的标准试验方法、实施和术语

1.1 This standard covers definitions, reference methods, practices, and guides relating to the chemical analysis of steel, stainless steel, and related alloys. It includes both wet chemical and instrumental techniques. 1.2 Directions are provided for handling chemical requirements, product analyses, residual elements, and reference standards, and for the treatment and reporting of chemical analysis data. 1.3 This standard applies only to those product standards which include this standard or parts thereof as a requirement. 1.4 In cases of conflict, the product specification requirements shall take precedence over the requirements of this standard. 1.5 Attention is directed to Practice A880 when there may be a need for information on criteria for evaluation of testing laboratories. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products