H42 铁合金 标准查询与下载

ISO 5449:1980 硅铬铁 规范和交货条件

Refers to ferrosilicochromium usually supplied for steelmaking and foundry use. Specifies definition, information for ordering, requirements, testing, despatch and storage.

Ferrosilicochromium; Specification and conditions of delivery

JIS G 4106:1979 机械结构用锰钢及锰铬钢钢材

Manganese steels and manganese chromium steels for machine structural use

JIS G 4104:1979 铬钢钢材

Chromium steels

JIS G 4105:1979 铬钼钢钢材

Chromium molybdenum steels

JIS G 4202:1979 铝铬钼钢

Aluminium chromium molybdenum steels

ASTM A610-79(2009) 尺寸测量用铁合金的取样和试验的标准试验方法

1.1 These test methods cover procedures for the sampling and testing of the various ferroalloys for sizing, either before or after shipment from the plants of the manufacturers. 1.2 They are designed to give results representative of each lot that will be comparable with the manufacturer''s certified analysis for the same lot. 1.3 The purchaser may use any sampling procedure he desires, but the results obtained on such samples shall not be a basis for complaint or rejection, unless the procedure followed is of an accuracy equivalent to that prescribed in these test methods. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4.1 Exception8212;The SI units that correspond to mesh sizes in Table 1 are to be regarded as standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Sampling and Testing Ferroalloys for Determination of Size

ASTM A610-79(2004) 尺寸测量用铁合金的取样和试验的标准试验方法

1.1 These test methods cover procedures for the sampling and testing of the various ferroalloys for sizing, either before or after shipment from the plants of the manufacturers. 1.2 They are designed to give results representative of each lot that will be comparable with the manufacturer''s certified analysis for the same lot. 1.3 The purchaser may use any sampling procedure he desires, but the results obtained on such samples shall not be a basis for complaint or rejection, unless the procedure followed is of an accuracy equivalent to that prescribed in these test methods. 1.4 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents of inch-pound units may be approximate. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Sampling and Testing Ferroalloys for Determination of Size

UNI 7857-1978 低锰铁合金．质量，规定和试验

Riguarda la ghisa speculare usata principalmente come deossidante e desolforante o come elemento di lega nella produzione della ghisa e dell' acciaio. La ghisa speculare è fornita allo stato solido. La ghisa speculare è una lega di ferro e carbonio che contiene inoltre manganese da oltre 6 fino al 30%. Qualità. Condizioni di fornitura.

Spiegeleisen. Qualities, requirements and tests.

NF A13-030:1976 铁合金.硅锰铁.规范

Ferro-alloys. Ferrosilicomanganese. Specifications.

NF A13-050:1976 铁合金.硅铬铁.规范

Ferro-alloys. Ferrosilicochromium. Specifications.

NF A13-040:1976 铁合金.铬铁.规范

Ferro-alloys. Ferrochromium. Specifications.

NF A13-020:1975 铁合金.锰铁合金.规范

Ferro-alloys. Ferro-manganese. Specifications.

NF A13-010:1974 铁合金.硅铁.要求

Ferro-alloys. Ferrosilicon. Requirements.

ASTM A324-73(2004) 钛铁合金

1.1 This specification covers four grades of ferrotitanium, designated A, B, C, and D.

Standard Specification for Ferrotitanium

ASTM A144-73(1990) 钨铁合金规范

1.1 This specification covers four grades of ferrotungsten.

Specification for Ferrotungsten

ASTM A144-73(1990)e1 钨铁合金规范

1.1 This specification covers four grades of ferrotungsten.

Specification for Ferrotungsten