H42 铁合金 标准查询与下载

YB/T 093-1996 低铬合金铸铁段

Low chromium alloy cast iron section

NF C28-926:1996 以半加工状态交付的冷轧合金电工钢片和电工钢带

Cold rolled electrical alloyed steel sheet and strip delivered in the semi-processed state.

NF C28-920:1996 以全加工状态交付的晶纹理取向的电工钢片和电工钢带

Grain-oriented electrical steel sheet and strip delivered in the fully processed state.

NF C28-925:1996 以半加工状态交付的冷轧非合金电工钢片和电工钢带

Cold rolled electrical non-alloyed steel sheet and strip delivered in the semi-processed state.

NF C28-900:1996 以全加工状态交付的冷轧非晶纹理取向的电工钢片和电工钢带

Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state.

ASTM B690-96 铁镍铬钼合金无缝管标准规范

1.1 This specification covers iron-nickel-chromium-molybdenum alloys (UNS N08366 and UNS N08367)* cold-finished annealed or hot-finished annealed seamless pipe and tube intended for use in special corrosive service and for heat-resisting applications. 1.2 Pipe and tube shall be supplied in the solution heat treated and descaled condition. When bright annealing is used, descaling is not necessary. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube

ASTM F30-96 铁镍密封合金标准规范

1.1 This specification covers iron-nickel alloys that are intended primarily for sealing to glass in electronic applications. Note 18212;Some of these alloys may be used for sealing to ceramics, but this specification in its present form is not intended to cover material for metal-to-ceramic seals.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The hazard statement pertains only to the test method sections, Sections 10 and 12.

Standard Specification for Iron-Nickel Sealing Alloys

ASTM F30-96(2002) 铁镍密封合金标准规范

1.1 This specification covers iron-nickel alloys that are intended primarily for sealing to glass in electronic applications. Note 18212;Some of these alloys may be used for sealing to ceramics, but this specification in its present form is not intended to cover material for metal-to-ceramic seals.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The hazard statement pertains only to the test method sections, Sections 10 and 12.

Standard Specification for Iron-Nickel Sealing Alloys

ISO 11949:1995 冷轧电镀锡板

Specifies requirements for single and double cold-reduced low-carbon mild steel for manufacture of electrolytic tinplate in form of sheets or coils.

Cold-reduced electrolytic tinplate

KS D 3629-1995 环氧树脂涂层钢筋

이 규격은 해수의 분위기에 사용되는 철근 콘크리티 보강용 이형 철근을 정전 스프레이 방법에

Fusion bonded epoxy coated reinforcing steel bars

YB/T 067-1995 硅钙钡铝合金

Silicon-calcium-barium-aluminium alloy

YB/T 547.1-1995 钒渣化学分析方法.硫酸亚铁铵滴定法测定五氧化二钒量

Methods for chemical analysis of vanadium slag the ammonium ferrous sulfate titrimetric method

ASTM B691-95 铁镍铬钼合金杆材、棒及线材标准规范

1.1 This specification covers iron-nickel-chromium-molybdenum alloys (UNS N08366 and UNS N08367)* in the form of hot-finished and cold-finished rounds, squares, hexagons, octagons, and rectangles. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Rod, Bar, and Wire

ISO 10386:1994 硼铁合金 规范和交货条件

Specifies requirements and conditions of delivery for ferroboron usually supplied for steelmaking and foundry use.

Ferroboron - Specification and conditions of delivery

YB/T 5141-1993 电焊条用还原钛铁矿粉

Reduced ilmenite powder for welding rod

YB/T 5140-1993 氮化铬铁

Ferrochromium Nitride

KS D 3851-1993 钛钯合金丝

이 규격은 단면이 원형인 내식용 티탄 팔라듐합금 선에 대하여 규정한다.

Titanium - Palladium alloy wires

YB/T 053-2000 包芯线

Cored wires

NF A13-601:1992 镍铁.规范和交货要求

Ferronickel. Specification and delivery requirements.

NF A13-602:1992 铁镍合金球.分析取样

Ferronickel shot. Sampling for analysis.