J19 联轴器、制动器与变速器 标准查询与下载

AQ/T 1110-2014 煤矿带式输送机用盘式制动装置安全检验规范

Specification for safety inspection of disc brake device for belt conveyor in coal mine

AQ/T 1109-2014 煤矿带式输送机用电力液压鼓式制动器安全检验规范

Specification for safety inspection of electrohydraulic drum brakes for belt conveyors in coal mines

JB/T 11619-2013 QDX点线啮合齿轮减速器

本标准规定了QDX点线啮合齿轮减速器的型式、基本参数、型号与尺寸、要求、试验方法、检验规则、标志、包装和贮运。本标准适用于QDX点线啮合齿轮减速器。

QDX point-line meshing gear reducers

JB/T 11618-2013 齿轮连环少齿差减速器

本标准规定了齿轮连环少齿差减速器的术语和定义、型式、型号与命名、基本参数、尺寸、技术要求、试验方法、检验规则、标志、包装、运输及贮存。本标准适用于齿轮连环少齿差减速器。

Gear connect-ring reducer with small tooth difference

JB/T 4234-2013 普通型、限矩型液力偶合器 铸造叶轮技术条件

本标准规定了普通型、限矩型液力偶合器铸造叶轮的技术要求、试验方法、运输和贮存。本标准适用于普通型、限矩型液力偶合器的铸造叶轮(以下简称叶轮)。

General type and load limiting type of constant filling fluid couplings.Specification for casting impeller

JB/T 9001-2013 调速型液力偶合器 叶轮 技术条件

本标准规定了调速型液力偶合器、液力偶合器传动装置叶轮的技术要求。本标准适用于调速型液力偶合器、液力偶合器传动装置的叶轮。

Variable speed fluid couplings.Specification for impeller

SAE J318-2013 机动车空气制动线性联接器(汽车气闸线连接)

This SAE Recommended Practice is intended to provide a design, interchangeability dimensions, testing procedures, performance requirements, and minimum identification for gladhand-type air line couplers used to connect the brake systems of trucks, truck-tractors, trailers, and dollies when these vehicles are joint to operate as a combination unit. The purpose is to provide coupler halves for brake lines on one vehicle that will be identified and compatible with the coupler halves on the brake lines of another vehicle.

Automotive Air Brake Line Couplers (Gladhands)

BS ISO 14541:2013 液压机液体.通用螺旋连接到连接器速动联轴器的尺寸规格和要求

Hydraulic fluid power. Dimensions and requirements for screw-to-connect quick-action couplings for general purpose

BS ISO 14540:2013 液压机液体.72 MPa(720 bar)下使用的螺旋到连接速动联轴器要求和尺寸规格

Hydraulic fluid power. Dimensions and requirements for screw-to-connect quick-action couplings for use at a pressure of 72 MPa (720 bar)

JB/T 11587-2013 大型牙嵌式离合器

本标准规定了公称转矩为630N · m~100 000N · m的牙嵌式电磁离合器(以下简称离合器)的分类、结构型式、基本参数和主要尺寸、技术要求、试验方法、检验规则、标志、包装和贮存。本标准适用于DYB型和DYK型,端面齿无润滑、线圈旋转型及接合时主、从动端相对速度为零的牙嵌式电磁离合器。

Large toothed electromagnetic clutch

JB/T 11586-2013 ZJG板带轧机主传动鼓形齿式接轴

本标准规定了ZJG板带轧机主传动鼓形齿式接轴(以下简称接轴)的结构形式、基本参数和主要尺寸、标记、技术要求、试验方法、检验规则、标志、包装和贮存。本标准适用于连接板带轧机轧辊与齿轮机座输出轴两个传动轴系的接轴。

ZJG crown gear type coupling for master drive of continuous board and belt rolling mill

JB/T 11594-2013 WJKC型、CGWK型吊车轨道固定件

本标准规定了WJKC型、CGWK型轨道固定件的结构、尺寸、标识、技术要求以及包装和贮存。本标准适用于大吨位软钩起重机及带水平导向轮起重机轨道的固定件。

The type of WJKC、CGWK crane track fixtures

SAE J1259-2012 公制球形杆端

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard covers the general and dimensional data for industrial quality spherical rod ends commonly used on control linkages in metric automotive, marine, construction, and industrial equipment applications. The rod ends described are available from several manufacturers within the range of the interchangeable specifications. The sliding contact spherical self- aligning bearing members (ball and socket) are availabl

Metric Spherical Rod Ends

ANSI/AWWA C221-2012 钢制机械套筒式补偿器

This standard describes fabricated steel mechanical slip-type expansion joints having packing chambers for use on pipe with plain, flanged, grooved, or shouldered ends in nominal pipe sizes from 3 in. through 144 in. (75 mm through 3,600 mm). The joints shall be manufactured from steel and are intended for use in systems conveying water. Mechanical expansion joints are not intended for use in buried conditions.

Fabricated Steel Mechanical Slip-Type Expansion Joints

JB/T 10163-2011 干式多片电磁离合器

本标准规定了干式多片电磁离合器的术语和定义、分类、特性、产品的有关资料、正常的使用、安装和运输条件、结构和性能要求、试验等。 本标准适用于干式多片电磁离合器（以下简称离合器），该离合器在机械传动系统中，可在主动部分运转的情况下，使从动部分与主动部分结合或分离。 本标准也适用于干式多片电磁制动器。

Electromagnetic multi-disc clutches for dry running

JB/T 11100-2011 螺旋卸料离心机用差速器.渐开线行星齿轮差速器

本标准规定了螺旋卸料离心机用渐开线行星齿轮差速器的型式与基本参数、要求、试验方法、检验、规则、标志、包装、运输和贮存。 本标准适用于传动级数为二级和三级的螺旋卸料离心机用渐开线行星齿轮差速器(以下简称差速器)。

Scroll discharge centrifuge differential case. Involute planetary gear box

JB/T 11099-2011 螺旋卸料离心机用差速器.摆线针轮差速器

本标准规定了螺旋卸料离心机摆线针轮差速器的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于螺旋卸料离心机捏线针轮差速器(以下简称差速器)。

Scroll discharge centrifuge differential case.Cycloidal drives

ANSI/AGMA 9110-2011 柔性耦合器.潜在不平衡的分级(公制版本)

This standard describes coupling unbalance and identifies its sources. It breaks down the requirements into usable groups and outlines how to calculate the potential unbalance of the coupling. A guide is provided for unbalance class selection for purchasers who have not defined the coupling balancing requirements for their system.

Flexible Couplings - Potential Unbalance Classification (Metric Edition)

ANSI/AGMA 9000-2011 柔性耦合器.潜在不平衡的分类

Describes potential coupling unbalance and identifies its sources. The Standard breaks down the requirements into usable groups and outlines how to calculate the potential unbalance of the coupling.

Flexible Couplings - Potential Unbalance Classification

JB/T 7936-2010 直廓环面蜗杆减速器

本标准规定了直廓环面蜗杆减速器(以下简称减速器)的型式与基本参数、技术要求、试验方法与检验规则、标志、包装、运输与贮存等。 本标准适用于冶金、矿山、起重、运输、石油、化工、建筑等机械设备用的减速器。

Hindley worm reduction units