J36 热处理 标准查询与下载

JB/T 9211-1999 中碳钢与中碳合金结构钢马式体等级

本标准规定了中碳钢与中碳合金结构钢马氏体显微组织的检验方法以及马氏体金相图片。 本标准适用于评定中碳钢与中碳合金结构钢整体淬火或淬火后200℃以下回火的马氏体组织。

Martensite grade of medium-carbon steel and medium - carbon alloy structural steel

JB/T 9210-1999 真空热处理

本标准规定了真空热处理设备的特殊要求，真空热处理常用金属材料，真空热处理的工艺过程及其基本工艺参数。 本标准适用于金属的真空淬火、真空回火、真空退火、真空固溶热处理及真空时效等工艺。

Vacuum heat treatment

JB/T 9209-1999 化学热处理渗剂.技术条件

本标准规定了化学热处理渗剂的技术要求、安全要求和试验方法等。 本标准适用于碳素钢、合金钢、铸铁及其它金属材料与粉末冶金制品进行化学热处理时采用的渗剂。

Technical requirement of medium for thermo - chemical treatment

JB/T 9208-1999 可控气氛分类及代号

本标准规定了热处理用的可控气氛分类及代号。适用于渗碳、碳氮共渗等化学热处理和保护加热的可控气氛。

Classifications and symbols of controlled atmospheres

JB/T 9207-1999 钢件在吸热式气氛中的热处理

本标准规定了钢件在吸热式气氛中的原料气、发生器、热处理炉、热处理质量控制、检验及安全等的基本要求。 本标准适用于渗碳，也适用于碳氮共渗、光亮或洁净淬火、正火、氮碳共渗及复碳等工艺。

Heat traetment of steels in endothermic atmospheres

JB/T 9206-1999 钢铁热浸铝工艺及质量检验

本标准规定了钢铁热浸铝工艺要点和热浸铝层质量检验方法。 本标准适用于碳素钢、合金钢、铸铁件的热浸铝工艺和产品的质量检验。不适用于连续式热浸铝生产的薄板带材和线材制品。

Technology and quality inspection for hot-dipped aluminum coatings on iron or steel

JB/T 9205-1999 珠光体球墨铸铁零件感应淬火金相检验

本标准规定了珠光体球墨铸铁零件感应淬火金相检验的技术要求及相应的检验方法。适用于珠光体含量不低于75%的球墨铸铁零件经高、中频感应淬火低温回火(回火温度≤200℃)后的硬化层金相组织及硬化层深度的检验。

Metallographic examination of induction hardened pearlitic spheroidal graphite cast iron parts

JB/T 9204-1999 钢件感应淬火金相检验

本标准规定了钢件感应淬火金相检验的技术要求及相应的检验方法。 本标准适用于中碳碳素结构钢和中碳合金钢制造的机械零件，经高、中频感应淬火后金相组织及有效硬化层深度的检验。

Metallographic examination of induction hardened steel parts

JB/T 9203-1999 固体渗碳剂

本标准规定了固体渗碳剂的技术要求、分析方法、检验规则及包装、运输、贮存和标志。 本标准适用于低碳钢和低碳合金钢零件渗碳用的固体渗碳剂。

Solid carburizer

JB/T 9201-1999 钢铁件的感应淬火回火处理

本标准规定了钢铁件的感应淬火回火质量控制及劳动保护的基本要求。适用于钢铁感应淬火(电流频率50～1000 Hz)并进行炉中回火或自回火的热处理工艺。

Induction hardening and tempering of iron and steel parts

JB/T 9200-1999 钢铁件的火焰淬火回火处理

本标准规定了钢铁件的火焰淬火回火的质量控制及劳动保护的基本要求。适用于钢铁件的火焰淬火后，在加热设备中进行回火的处理，也适用于火焰淬火自热回火的处理。

Frame hardening and tempering of iron and steel parts

JB/T 9197-1999 不锈钢和耐热钢热处理

本标准规定了不锈钢和耐热钢热处理的方法及所用的设备、工艺、工艺材料、质量检验和安全技术。 本标准适用于不锈钢和耐热钢的热处理。

Heat treating for stainless steel and heat - resisting steel

JIS B 6911:1999 钢铁的正火与退火工艺

この規格は，鉄鋼の焼ならし及び焼なまし加工(以下，加工という。)について規定する。備考 部分熱処理は除く。

Process of normalizing and annealing of iron and steel

JIS B 6915:1999 钢铁的渗氮和碳氮共渗工艺

この規格は，鉄鋼の窒化・軟窒化及び酸窒化加工(以下，加工という。)について規定する。

Process of nitriding and nitrocarburizing of iron and steel

JIS B 6913:1999 钢铁的淬火和回火工艺

この規格は，鉄鋼の焼人焼戻し加工(以下，加工という。)について規定する。備考 表面熱処理は除く。

Process of quenching and tempering of iron and steel

JIS B 6901:1998 金属的热处理炉.有效工作区和有效处理区的试验方法

この規格は，金属熱処理設備(以下，熱処理設備という。）の有効加熱带の試験方法について規定する。プラズマ熱処理加熱設備の有効処理带試験方法については，附属書1による。加熱設備の保持温度許容差は，附属2，有効加熱带及び有効処理帯の判定方法は，附属書3による。

Heat treatment furnaces of metals -- Test methods of effective working zone and effective treating zone

BOCA IOTFDC-1998 APPENDIX B-1998 游泳池,温泉及热技术研究所

The following is a listing of the standards referenced in this code, the effective date of the standard, the promulgating agency of the standard and the section(s) of this code that refer to the standard.

Swimming Pools, Spas and Hot Tubs

DIN 17022-4:1998 钢铁材料热处理.热处理方法.第4部分:渗氮和硝基渗碳

The document describes methods of heat treatment and gives notices for nitriding and nitrocarburizing.

Heat treatment of ferrous materials - Methods of heat treatment - Part 4: Nitriding and nitrocarburizing

BS EN 746-1:1997 工业热加工设备.工业热加工设备的通用安全性要求

1 This part of EN 746 specifies common safety requirements for industrial thermoprocessing equipment (for example industrial furnaces and industrial heating equipment), which meets the definition for machinery given in EN 292-1:1991. It details the anticipated significant hazards associated with industrial thermoprocessing equipment and specifies the appropriate preventative measures for reduction or elimination of these hazards. This standard gives general principles and common requirements for the reduction of risks for equipments covered by the scope. The common requirements apply to all of the subsequent parts of this EN 746 dealing with specific equipment unless an exception is stated in the relevant Part. The general principles (subclauses are pointed out) will be used to establish the specific technical measures in the subsequent Part(s) dealing with safety requirements for particular equipment NOTE. For similar equipment not covered by the particular Parts of this standard, EN 746-1 can be used to assist in the reduction of risk for the hazards identified in clause 4 (list of hazards). 2 This Part of EN 746 is applicable to industrial thermoprocessing equipments for use in fields such as: - metallurgical and metal working plant; - glass making plant; - ceramic manufacturing plant; - cement, lime and gypsum manufacturing plant; - chemical plant; - waste incineration equipment; and heated by: - gaseous fuels; - liquid fuels; - solid fuels; - mixed fuels; - electricity. The thermoprocessing equipment covered by this Part of EN 746 is further specified in clause 3. A more detailed list of thermoprocessing equipment within these categories is given in annex A. In the remainder of this standard the expression 'equipment' will be used. This Part of EN 746 is not applicable to blast furnaces, converters (in steel plants), boilers, welding machines or food processing equipment. 3 This Part of EN 746 specifies the requirements to be met by the manufacturer to ensure the safety of persons and property during commissioning, startup, operation, shut-down, maintenance periods and dismantling, as well as in the event of foreseeable faults or malfunctions which can occur in the equipment. It specifies the safety requirements at stages in the life of the equipment, and its design, ordering, construction, use and disposal It specifies safety requirements for: - protection against: - mechanical hazards, movement of machinery and material, ejection of parts or material or liquids and gases, implosion, structural failure; - electrical hazards; - thermal hazards: explosion, fire, scalds, contact with hot parts, gases and flames; - noise and vibration; - thermal, optical and ionising and non-ionising radiation; - harmful by-products and hazardous substances, poisoning, biological and micro-biological contamination, pollution and environmental discomfort; - other hazards such as listed in clause 4; - maintenance, provision for indicators, and inspection. This part of EN 746 applies to equipment which is placed on the market after the date of issue of this standard.

Industrial thermoprocessing equipment - Common safety requirements for industrial thermoprocessing equipment

JB/T 8555-1997 热处理技术要求在零件图样上的表示方法

本标准规定了钢制零件热处理技术要求在图样上的表示方法。 本标准适用于各种钢制的机械零件。

Representation of heat treatment technical requirements on part drawings