J47 手工工具 标准查询与下载

SANS 8764-1:2009 螺钉和螺母用安装工具．十字槽头螺钉用旋具．第1部分：驱动头

Specifies the shapes and dimensions, technical requirements and torque test methods for the tips of hand drivers and of machine-operated bits for cross-recessed head screws. It specifies two forms of driver tips: form PH for form H recesses and form PZ f

Assembly tools for screws and nuts - Screwdrivers for cross-recessed head screws Part 1: Driver tips

SANS 8764-2:2009 螺钉和螺母用安装工具．十字槽头螺钉用旋具．第2部分：手动旋具刀身长度和标记的一般要求

Specifies general requirements, lengths of blades and marking of hand-operated screwdrivers for H and Z cross-recessed head screws as specified in ISO 4757. The specifications for blade tips are given in ISO 8764-1.

Assembly tools for screws and nuts - Screwdrivers for cross-recessed head screws Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers

NF E74-301:2009 螺钉和螺母的组装工具.工程使用低扭矩单头扳手.扳手头和试验扭矩的最大外尺寸

Assembly tools for screws and nuts - Single-head engineer's wrenches for lower torque applications - Maximum outside dimensions of heads and test torques.

NF E74-304:2009 螺钉和螺母装配工具.双头开式扳手,双头套筒扳手和组合扳手.扳手最大开宽度

Assembly tools for screws and nuts - Double-headed open-ended wrenches, double-headed box wrenches and combination wrenches - Maximum widths of heads.

NF E74-367:2009 螺钉和螺母装配工具.动力套筒扳手用六角方形加长杆或圆柱平头加长杆

Assembly tools for screws and nuts - Square drive adaptor with hexagon or cylindrical flat drive, for power socket wrenches.

DIN 905:2009 螺钉和螺母装配工具.内套筒四方T形扳手.技术规范

Assembly tools for screws and nuts - Tee wrenches, male square - Technical specifications

DIN 7427:2009 螺钉和螺母装配工具 机用螺钉旋具插头用带内六角头的连接件 技术规范

Assembly tools for screws and nuts - Square drive sockets and hexagon drive extensions for hexagon insert bits - Technical specifications

DIN 133:2009 螺钉和螺母装配工具.敲击扳手,开口端.技术规范

Assembly tools for screws and nuts - Slugging wrenches, open end - Technical specifications

DIN 5200:2009 螺钉和螺母用装配工具.双偏置槽头螺钉用螺丝刀.尺寸规格和要求

Assembly tools for screws and nuts - Screwdrivers for slotted head screws, double offset - Dimensions and requirements

DIN 7444:2009 螺钉和螺母装配工具.敲击套筒扳手.技术规范

Assembly tools for screws and nuts - Slugging wrenches, box - Technical specifications

ISO 3317:2009 螺钉和螺母用装配工具.机动套筒扳手用带六角形或圆柱平传动的方形传动接头

Assembly tools for screws and nuts - Square drive adaptor with hexagon or cylindrical flat drive, for power socket wrenches

DIN ISO 1173:2009 螺钉和螺母用装配工具.机动和手动螺丝起子的驱动端和连接部件.尺寸和扭矩试验(ISO 1173:2001),DIN ISO 1173:2009-06的英文版本

This International Standard specifies the dimensions and torque testing of drive ends for hand- and machine-operated screwdriver bits as well as to driving spindles of screw driving machines. It ensures the interchangeability of tool bits and tool holders. This International Standard defines only the distinctive features of individual drive ends. Details of design, e.g. of fixing devices, are left to the user of this International Standard.

Assembly tools for screws and nuts - Drive ends for hand- and machine-operated screwdriver bits and connecting parts - Dimensions, torque testing (ISO 1173:2001);English version of DIN ISO 1173:2009-06

ISO 3318:2009 螺钉和螺母用装配工具.双头呆扳手,双头梅花扳手和两用扳手.头部的最大宽度

Assembly tools for screws and nuts - Double-headed open-ended wrenches, double-headed box wrenches and combination wrenches - Maximum widths of heads

DIN 5129:2009 劈木锤

Wood splitting hammers

ISO 4229:2009 螺钉和螺母用装配工具.工程师用低扭矩单头扳手.最大头部尺寸及测试扭矩

Assembly tools for screws and nuts - Single-head engineer's wrenches for lower torque applications - Maximum outside dimensions of heads and test torques

DIN EN 792-13:2009 手持非电动工具.安全性要求.第13部分:紧固件扳拧工具

This standard is applicable to fastener driving tools which are handled by one person and in which energy in a linear movement is applied to a loaded fastener for the purpose of driving this into a workpiece of a determined material. During the driving operation, the fastener leaves the tool partially or entirely, with sufficient velocity to overcome the resistance of penetration, and forms a mechanical connection or attachment of different workpieces. The energy required for driving a fastener is provided by compressed air or combustible gases. NOTE 1 Fastener driving tools are also referred to for example as Nailers, Staplers, Tackers, Pinners. NOTE 2 The workpiece material can, for example, consist of wood, wooden materials, plastic material, fibre materials - loose or condensed, cement- and lime materials, metal. This standard contains requirements for the design, marking and information for use of fastener driving tools, corresponding to the specific hazards listed in clause 4. The standard sets out the means of verification for these requirements. Where, for clarity, an example of a safety measure is given in the text, this shall not be considered as the only possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent level of safety is achieved. This standard is applicable to fastener driving tools which have been produced after the date of publication of the standard. This standard is not applicable to stapling pliers and vibration hammers. NOTE 3 "Stapling pliers" are handheld power operated tools equipped with a fixed or moving anvil bar in front of the muzzle, which are used predominantly for joining paper, leather, textiles and similar materials. This standard is not applicable to fastener driving tools in which the energy for driving fasteners is drawn from cartridges or from any type of electric supply.

Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools; German version EN 792-13:2000+A1:2008

JIS B 4636-1 ERRATUM 1:2008 勘误表

ERRATUM

NF E65-100-13:2008 手持式非电动工具.安全要求.第13部分:紧固件驱动工具

Hand-held non-electric power tools - Safety requirements - Part 13 : fastener driving tools.

SANS 387:2008 锤头和手锤

Covers the requirements for 14 types of hammer heads and hand hammers, the handles of hammers being of wood , steel or glass fibre reinforced plastics. Includes requirements for material, dimensions and hardness of hammer heads, and methods of test for c

Hammer heads and hand hammers

DIN 900:2008 螺钉和螺母用装配工具.管钳子用螺丝钻.技术规范

Assembly tools for screws and nuts - Tommy bars for socket wrenches - Technical specifications