J47 手工工具 标准查询与下载

QB/T 2212.5-2011 建筑工具（泥工类）砌刀

本标准适用于QB/T 2212.1《建筑工具（泥工类）通用技术条件》中规定的砌刀。 本标准规定了砌刀的产品分类、技术要求、试验方法、检验规则及包装、标志、运输、贮存。

Builder's tools (masonry).Brick knives

QB/T 2212.4-2011 建筑工具（泥工类）砌铲

本标准适用于QB/T 2212.1《建筑工具（泥工类）通用技术条件》中规定的砌铲。 本标准规定了砌铲的产品分类、技术要求、试验方法、检验规则及包装、标志、运输、贮存。

Builder's tools (masonry).Brick trowels

QB/T 2212.1-2011 建筑工具（泥工类）通用技术条件

本标准规定了建筑工具(泥工类)的分类与命名、技术要求、试验方法、检验规则及包装、标志、运输、贮存。 本标准的工具图示仅是示例，并不影响对产品的设计。

Builder's tools (masonry).Gengeral requirements

QB/T 2212.6-2011 建筑工具（泥工类）打砖工具

本标准适用于QB/T 2212.1《建筑工具（泥工类）通用技术条件》中规定的打砖工具。 本标准规定了打砖工具的产品分类、技术要求、试验方法、检验规则及包装、标志、运输与贮存。

Builder's tools (masonry).Brick tools

ISO 1174-1:2011 螺钉与螺母的装配工具.驱动方头.第1部分:手动套筒工具的驱动方头

This part of ISO 1174 specifies the dimensions, separation force and designation of driving squares for hand socket tools. NOTE Driving squares for power socket tools are dealt with in ISO 1174-2.

Assembly tools for screws and nuts - Driving squares - Part 1: Driving squares for hand socket tools

ISO 3315:2011 螺钉和螺母用装配工具.手动方榫传动套筒扳手传动件.尺寸规格和试验

This International Standard is applicable to the driving parts of hand-operated square drive socket wrenches identified in ISO 1703 under designations 6 1 00 04 0, 6 1 00 06 0, 6 1 00 06 1, 6 1 00 09 0, 6 1 00 10 0, 6 1 00 10 1, 6 1 00 01 0, 6 1 00 01 1, 6 1 00 03 0, 6 1 00 05 0 and 6 1 00 05 1. NOTE These designations correspond to the former (old) designation numbers 253, 255, 256, 257, 251, 252 and 254. It specifies a) the overall dimensions, b) the minimum Rockwell hardness value for their squares, c) the method of torque testing, d) the minimum torsional strength values, e) the method endurance of testing for ratchet handles, f) designation, and g) marking.

Assembly tools for screws and nuts - Driving parts for hand-operated square drive socket wrenches - Dimensions and tests

DIN 7431:2011 六角嵌入式刀头用螺丝刀

Screwdrivers for hexagon insert bits

DIN EN ISO 11148-6:2011 手持非电动工具.安全性要求.第6部分:螺纹结件用装配电动工具(ISO 11148-6-2010).德文版本EN ISO 11148-6-2010

Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners (ISO 11148-6:2010); German version EN ISO 11148-6:2010

ANSI/SCTE 14-2011 六角压接工具的检定/校准的测试方法

The purpose of this standard is to determine and verify the actual crimp dimension of hex crimp tools, measurement technique for determining the final hex size that may affect pull-off performance of the cable-to-connector interface, calibration technique for adjusting hex crimp tools.

Test Method for Hex Crimp Tool Verification/Calibration

ISO 11148-4:2010 手持式非电动工具.安全要求.第4部分:非旋转冲击动力工具

IMPORTANT — The electronic file of this document contains colours that are considered useful for the correct understanding of the document. Users should consider printing this document using a colour printer. ISO 3864-1 provides colorimetric and photometric properties together with, as a guideline, references from colour order systems. This part of ISO 11148 applies to hand-held non-electric power tools (hereafter referred to as “non-rotary percussive power tools”) intended for chipping, riveting, breaking of concrete and asphalt, ramming, etc. The non-rotary percussive power tool can be powered by compressed air, hydraulic fluid or internal combustion engines and is intended for use by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer. This part of ISO 11148 covers - breakers; - bush hammers; - chipping hammers; - small chisels; - engraving pens; - needle scalers; - pick hammers; - pile drivers; - portable pile drivers; - punches; - rammers; - riveting hammers; - scaling hammers; - stone hammers; - spades; - tampers. NOTE 1 For examples of non-rotary percussive power tools, see Annex B. This part of ISO 11148 does not cover special requirements and modifications on non-rotary percussive power tools for the purpose of mounting in a fixture. This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardous events when the tools are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of non-rotary percussive power tools in potentially explosive atmospheres. NOTE 2 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive atmospheres.

Hand-held non-electric power tools. Safety requirements. Part 4: Non-rotary percussive power tools

ISO 11148-6:2010 手持式非电动工具.安全性要求.第6部分:螺纹结件用装配电动工具

IMPORTANT — The electronic file of this document contains colours that are considered useful for the correct understanding of the document. Users should consider printing this document using a colour printer. ISO 3864-1 provides colorimetric and photometric properties together with, as a guideline, references from colour order systems. This part of ISO 11148 applies to hand-held non-electric power tools (hereafter referred to as “assembly power tools for threaded fasteners”) intended for tightening or installing of threaded fasteners. The assembly power tools for threaded fasteners can be powered by compressed air, hydraulic fluid or internal combustion engines and are intended for use by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer. This part of ISO 11148 covers - air-hydraulic impulse wrenches; - impact wrenches; - fastener installation tools; - nutrunners; - open-ended spanners (crow-foot with open-ended socket or tube nut wrench); - ratchet wrenches; - screwdrivers. NOTE 1 For examples of assembly power tools for threaded fasteners, see Annex B. This part of ISO 11148 does not cover special requirements and modifications of assembly power tools for threaded fasteners for the purpose of mounting them in fixtures. This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardous events when the tools are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of assembly power tools for threaded fasteners in potentially explosive atmospheres. NOTE 2 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive atmospheres.

Hand-held non-electric power tools.Safety requirements.Part 6: Assembly power tools for threaded fasteners

ISO 11148-3:2010 手持式非电动工具.安全要求.第3部分:钻孔机与攻丝机

IMPORTANT — The electronic file of this document contains colours that are considered useful for the correct understanding of the document. Users should consider printing this document using a colour printer. ISO 3864-1 provides colorimetric and photometric properties together with, as a guideline, references from colour order systems. This part of ISO 11148 applies to hand-held non-electric power tools (hereafter referred to as “drills and tappers”) intended for rotary drilling of holes in all kinds of material, e.g. wood, metal, concrete, plastics, etc., or for tapping and cleaning threads in metal and plastics. The drills and tappers can be powered by compressed air, hydraulic fluid or internal combustion engines and are intended for use by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer. This part of ISO 11148 is applicable to ? drills; ? heavy duty drills with two handles; ? tappers. NOTE 1 For examples of drills and tappers, see Annex B. This part of ISO 11148 is not applicable to special requirements and modifications of drills and tappers for the purpose of mounting them in fixtures. This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardous events when drills and tappers are used as intended and under conditions of misuse that are reasonably foreseeable by the manufacturer, with the exception of their use in potentially explosive atmospheres. NOTE 2 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive atmospheres.

Portable non-electric powered machines - Safety requirements - Part 3: Drilling and tapping machines (Second edition)

QB/T 1290.1-2010 钢锤 八角锤

本标准规定了八角锤的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于作业用钢制八角锤。

Hand hammers.Double-face sledge hammers

QB/T 1290.10-2010 钢锤 石工锤

本标准规定了石工锤的产品分类、要求、试验方法、检验规则、标志、标签、包装、运输和贮存。 本标准适用于作业用钢制石工锤。

Hand hammers.Club hammers

QB/T 1290.6-2010 钢锤 敲锈锤

本标准规定了敲锈锤的产品分类、要求、试验方法、检验规则、标志、标签、包装、运输和贮存。 本标准适用于作业用钢制敲锈锤。

Hand hammers.Boiler scaling hammers

QB/T 4062-2010 通用型大力钳

本标准规定了通用型大力钳的产品分类和标记、技术要求、试验方法、检验规则和包装、标志、运输、贮存。 本标准适用于具有夹持、扳拧和夹持锁定或兼有剪切功能的通用型大力钳。

General locking pliers

QB/T 1290.2-2010 钢锤 圆头锤

本标准规定了圆头锤的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于作业用钢制圆头锤。

Hand hammers.Engineer's ball pein hammers

QB/T 1290.7-2010 钢锤 焊工锤

本标准规定了焊工锤的产品分类、要求、试验方法、检验规则、标志、标签、包装、运输和贮存。 本标准适用于作业用钢制焊工锤。

Hand hammers.Welder's chipping hammers

QB/T 1290.3-2010 钢锤 钳工锤

本标准规定了钳工锤的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于作业用钢制钳工锤。

Hand hammers.Double-face sledge hammers

QB/T 1290.4-2010 钢锤 扁尾锤

本标准规定了扁尾锤的产品分类、要求、试验方法、检验规则、标志、标签、包装、运输和贮存。 本标准适用于作业用钢制扁尾锤。

Hand hammers.Cross pein hammers