J47 手工工具 标准查询与下载

SANS 1120:2008 钳子和镊子

Covers the material, dimensional, constructional and performance requirements for 12 types of pliers and 3 types of nippers. Strength of handles, insulation on handles, resistance to torsion, cutting ability and finish are included.

Pliers and nippers

NF E74-382*NF ISO 4228:2008 扳手和扳钳.电动套筒扳手用花键传动头

Spanners and wrenches - Spline drive ends for power socket wrenches.

SANS 1152:2008 手持式金属加工凿

Covers the material, dimensional, finish and hardness requirements for 4 types of metal-working chisels for hand use.

Metal-working chisels for hand use

SANS 1112:2008 呆扳手、梅花扳手和两用扳手

Covers the requirements for the material, dimensions, performance, and finish of three types of wrenches that are commonly referred to as spanners.

Open-end, box, and combination wrenches

SANS 1028:2008 管钳(公制单位)

Covers the material, constructional, finish and performance requirements for adjustable pipe wrenches of the heavy duty and Stillson types of nominal sizes in the range 200-1200 mm.

Pipe wrenches (Metric units)

QB/T 3002-2008 梅花扳手

本标准规定了梅花扳手的产品分类、技术要求、试验方法、检验规则与包装、标志、运输、贮存。 本标准适用于扳拧螺栓和螺母或其他坚固件的梅花扳手。

Box wrenches

QB/T 3001-2008 呆扳手

本标准规定了呆扳手的产品分类、技术要求、试验方法、检验规则与包装、标志、运输、贮存。 本标准适用于扳拧螺栓和螺母或其他坚固件的呆扳手。

Open ended wrenches

QB/T 3003-2008 两用扳手

本标准规定了两用扳手的产品分类、技术要求、试验方法、检验规则与包装、标志、运输、贮存。 本标准适用于扳拧螺栓和螺母或其他坚固件的两用扳手。

Combination wrenches

QB/T 3004-2008 电讯剪切钳

本标准规定了电讯剪切钳的产品分类、技术要求、试验方法、检验规则与标志、包装、运输、贮存。 本标准适用于电讯剪切钳。本标准不适用于带电作业剪切钳。 本标准的产品型式图示仅是示例，并不是影响对产品的设计。

Electronic nippers

QB/T 3005-2008 电讯夹扭钳

本标准规定了电讯夹扭钳的产品分类、技术要求、试验方法、检验规则与标志、包装、运输、贮存。 本标准适用于电讯夹扭钳。本标准不适用于带电作业夹扭钳。 本标准的产品型式图示仅是示例，并不影响对产品的设计。

Electronic pliers

SANS 390:2008 叉子和耙子

Covers the material, dimensional, constructional, strength, finish and marking requirements for 6 types of forks and 7 types of rakes.

Forks and rakes

BS EN 3711:2008 航空航天系列.十二角双头扳手.曲柄直线偏移量

This standard specifies the properties of the following types of double end box wrenches: double head flat, double head offset and double end modified offset.

Aerospace series - Wrench-double ended, bi-hexagonal - Straight, cranked, offset

DIN 898:2008 螺钉和螺母用装配工具.命名和术语(修改的ISO 1703-2005)

Assembly tools for screws and nuts - Designation and nomenclature (ISO 1703:2005, modified)

JIS B 4652:2008 手动扭矩工具.要求和试验方法

This Standard specifies the requirements, test method and marking for the hand torque tools used for controlled tightening of bolted connections (hereafter referred to as "torque tools"). This Standard is applicable to torque tools of clause 4, in particular to indicating and setting torque wrenches in accordance with No. 258 and No. 259 of ISO 1703: 1983 Assembly tools for screws and nuts Nomenclature. NOTE I This Standard specifies the requirements and test methods of torque tools shown for the target values for quality control, and it is not intended to perform the conformity assessment with this Standard. NOTE 2 The International Standard corresponding to this Standard is as follows. ISO 6789: 2003 Assembly tools for screws and nuts Hand torque tools-- Requirements and test methods for design conformance testing, quality con- /brmance testing and recalibration procedure (MOD) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/ IEC Guide 21.

Hand torque tools -- Requirements and test methods

JIS B 1015:2008 螺栓和螺钉用内板拧的六角花形

この規格は，ポルト及び小ねじ用のへクサロビュラ穴(以下，穴という。)の形状及び基準寸法並びにゲージによろ検査方法について規定する。

Hexalobular internal driving feature for bolts and screws

JIS B 4648:2008 内六角头螺丝扳手

This Standard specifies the hexagon socket screw keys (hereafter referred to as "screw keys"). Screw keys of this Standard shall be used for tightening of hexagon socket head screws for property class specified in JIS B 1051 and _j.!.S__B___!0_54-!., and for tighten- ing of hexagon socket set screws for property class specified in JIS B 1053 and JIS_B 1054-3. NOTE ~ The International Standard corresponding to this Standard is as follows. ISO 2936: 2001 Assembly tools for screws and nuts--Hexagon socket screw keys (MOD) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/ IEC Guide 21.

Hexagon socket screw keys

DIN 3125:2008 旋压式六角套筒扳手.尺寸和试验扭矩

Hexagon socket wrenches, spin type - Dimensions and test torques

ASME B107.600-2008 螺丝起子(ASME B107.15、B107.26、B107.30和B107.31的汇编)

This Standard covers straight handle-type screwdriversof flat tip design intended for manual operation indriving or removing screws with slotted recesses. Thescrewdrivers are of the types normally used by cabinetmakers,carpenters, sheet metal workers, productionworkers, mechanics, etc. The intention is to specify performancerather than design detail.Inclusion of dimensional data in the Standard is notintended to imply that all of the products describedherein are stock production sizes. Consumers arerequested to consult with manufacturers concerning listsof stock production sizes.Using a screwdriver as a pry bar or striking it with ahammer are clearly misuses of the tool, and nothing inthis Standard shall be interpreted as condoning any toolmisuse. Further information about proper use of screwdriversis contained in the Guide to Hand Tools —Selection, Safety Tips, Proper Use and Care.

Screwdrivers (Incorporation of ASME B107.15, B107.26, B107.30, and B107.31)

ANSI/ASME B107.41-2008 钉锤

This Standard provides performance and safety requirements for nail hammers that are intended specifically for use in driving or pulling unhardened nails and ripping apart or tearing down wooden components. It is intended to serve as a guide in selecting, testing, and using the hand tools covered herein. This Standard may be used as a guide by state authorities or other regulatory bodies in the formulation of laws or regulations. It is also intended for voluntary use by establishments that use or manufacture the tools covered.

Nail Hammers

ANSI/ASME B107.54-2008 重型锤击工具.安全要求

This Standard provides safety requirements for the design, construction, testing and use of the following styles of heavy striking tools: Blacksmith's Double-Face Sledges, Hand Drilling Hammers, Woodchoppers' Maul, Railroad Spike Maul, Spalling Hammers, Stone Sledge, Bush hammers, Boat Mauls and Lineman's or Farrier's Turning Hammers.

Heavy Striking Tools - Safety Requirements