J58 组合机床 标准查询与下载

JB/T 9889-1999 组合机床.滑台.精度检验

　 本标准规定了组合机床滑台的几何精度要求和检验方法。 　 本标准适用于组合机床及其自动线的滑台。

Combined machine tool Sliding table Accuracy inspection

JB/T 9890-1999 组合机床.多工位移动工作台.精度检验

　　本标准规定了组合机床多工位移动工作台的几何精度要求和检验方法。 　 本标准适用于组合机床及其自动线的工作台。

Combined machine tool Multi-position movable workbench Accuracy inspection

JB/T 9882-1999 组合机床.侧底座.精度检验

　　本标准规定了组合机床侧底座的几何精度要求和检验方法。 　 本标准适用于组合机床及其自动线的滑台侧底座,也适用于立柱侧底座。

Combined machine tool Wing base Accuracy inspection

JB/T 9884-1999 组合机床.精镗头.精度检验

　　本标准规定了组合机床精镗头的几何精度要求和检验方法。 　 本标准适用于组合机床及其自动线的精镗头。

Combined machine tool Fine boring heads Accuracy inspection

JB/T 9885-1999 组合机床.液压滑台.技术条件

　　本标准规定了组合机床液压滑台的制造和验收要求。 　 本标准适用名义尺寸100～800mm的组合机床液压滑台(含长台面型)。

Combined machine tool Hydraulic sliding table Technical conditions

JB/T 9886-1999 组合机床.镗孔车端面头.技术条件

　　本标准规定了组成合机床镗孔车端面头的制造和验收要求。 　 本标准适用于名义尺寸100～630mm的组成合机床镗孔车端面头。

Combined machine tool Hole boring end-face-turning unit head Technical conditions

JB/T 9887-1999 组合机床.镗削头.技术条件

　　本标准规定了组成合机床镗削头的制造和验收要求。 　 本标准适用于名义尺寸100～630mm的组成合机床镗削头。

Combined machine tool Boring and drilling head Technical conditions

BS ISO 10791-3:1999 加工中心检验条件.第3部分:分度或连续的万能主轴头机床的几何精度检验(垂直Z轴)

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with integral indexable or continuous universal heads (vertical Z-axis). This part of ISO 10791 applies to machining centres having basically six numerically controlled axes, of which three are linear (X, Y and Z) up to 2 000 mm in length, and three are rotary (A or D and B on the head, and C' on the table). Movements other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for three possible types of accessory universal heads, in the annexes: — annex A: Integral universal 45°split indexable heads (B and D axes), with mechanical indexing of the different angular positions of the two bodies (e.g. Hirth couplings): the relevant tests (AG1 to AG9) check only the resulting position of the spindle; — annex B: Integral universal swivel heads (B and A axes), with two numerically controlled rotary axes perpendicular to each other (tests BG1 to BG7); — annex C: Integral universal 45°split continuous heads (B and D axes), similar to the first type but provided with continuous positioning of the two numerically controlled rotary axes: the relevant tests (CG1 to CG7) check all the geometric features (planes and axes) which contribute to the resulting position of the spindle, excluding the positioning accuracy of the two rotary axes; these tests can also be used for a deeper investigation on the 45°indexable heads, if their movements and locks allow this. This part of ISO 10791 deals only with the verification of accuracy of the machine and does not apply to the testing of the machine operation, which should generally be checked separately. Certain tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions for machining centres - Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis)

NF E60-172-1:1999 多工序数控加工中心的试验条件.第1部分:带水平主轴和辅助头的机床的几何尺寸试验(水平的Z轴)

Test conditions of machining centres. Part 1 : geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z axis).

ISO 10791-3:1998 加工中心检验条件 第3部分:分度或连续的万能主轴头机床的几何精度检验(垂直Z轴)

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with integral indexable or continuous universal heads (vertical Z-axis). This part of ISO 10791 applies to machining centres having basically six numerically controlled axes, of which three are linear (X, Y and Z) up to 2 000 mm in length, and three are rotary (A or D and B on the head, and C' on the table). Movements other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for three possible types of accessory universal heads, in the annexes: — annex A: Integral universal 45°split indexable heads (B and D axes), with mechanical indexing of the different angular positions of the two bodies (e.g. Hirth couplings): the relevant tests (AG1 to AG9) check only the resulting position of the spindle; — annex B: Integral universal swivel heads (B and A axes), with two numerically controlled rotary axes perpendicular to each other (tests BG1 to BG7); — annex C: Integral universal 45°split continuous heads (B and D axes), similar to the first type but provided with continuous positioning of the two numerically controlled rotary axes: the relevant tests (CG1 to CG7) check all the geometric features (planes and axes) which contribute to the resulting position of the spindle, excluding the positioning accuracy of the two rotary axes; these tests can also be used for a deeper investigation on the 45°indexable heads, if their movements and locks allow this. This part of ISO 10791 deals only with the verification of accuracy of the machine and does not apply to the testing of the machine operation, which should generally be checked separately. Certain tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions of machining centres - Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis)

ISO 10791-1:1998 加工中心检验条件.第1部分:卧式和带附加主轴头的几何精度检验(水平Z轴)

This part of 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with horizontal spindle (i.e. horizontal Z-axis). This part of ISO 10791 applies to machining centres having basically four numerically controlled axes, of which three are linear (X, Y and Z) up to 2 000 mm in length, and one is rotary (B'), but refers also to supplementary movements, such as those of sliding spindles, rams, or accessory universal heads. Movements other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 takes into consideration, in annexes A, B and C, three possible types of accessory universal heads, described as follows: — annex A: 45°split indexable heads, with mechanical indexing of the different angular positions of the two bodies (e.g. Hirth couplings): the relevant tests (AG1 to AG9) check only the resulting position of the spindle; — annex B: swivel heads, with two numerically controlled rotary axes perpendicular to each other (tests BG1 to BG7); — annex C: 45°split continuous heads, similar to the first type but provided with continuous positioning of the two numerically controlled rotary axes: the relevant tests (CG1 to CG7) check all the geometric features (planes and axes) which contribute to the resulting position of the spindle, excluding the positioning accuracy of the two rotary axes; these tests can also be used for a deeper investigation of the 45°indexable heads, if their movements and locks allow this. This part of ISO 10791 deals only with the verification of geometric accuracy of the machine and does not apply to the testing of the machine operation, which should generally be checked separately. Certain tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions for machining centres - Part 1: Geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z-axis)

BS ISO 10791-4:1998 加工中心的试验条件.第4部分:线性和旋转轴定位的精度和可重复性

This part of ISO 10791 specifies, with reference to ISO 230-2, the tolerances which apply to the positioning tests for linear axes, up to 2 000 mm in length, and rotary axes of machining centres. It does not deal with environmental conditions, warm-up of the machine and measuring methods, already described in ISO 230-2.

Test conditions for machining centres - Accuracy and repeatability of positioning of linear and rotary axes

ISO 10791-4:1998 加工中心检验条件 第4部分:线性和回转轴线的定位精度和重复定位精度

This part of ISO 10791 specifies, with reference to ISO 230-2, the tolerances which apply to the positioning tests for linear axes, up to 2 000 mm in length, and rotary axes of machining centres. It does not deal with environmental conditions, warm-up of the machine and measuring methods, already described in ISO 230-2.

Test conditions for machining centres - Part 4: Accuracy and repeatability of positioning of linear and rotary axes

ISO 10791-6:1998 加工中心检验条件 第6部分:进给率、速度和插补精度

This part of ISO 10791 specifies, with reference to ISO 230-1, certain kinematic tests for machining centres, concerning the spindle speeds, the feeds of the individual NC linear axes and the accuracy of the paths described by the simultaneous movement of two or more NC linear and/or rotary axes (see clause 4).

Test conditions of machining centres - Part 6: Accuracy of feeds, speeds and interpolations

BS ISO 10791-5:1998 加工中心的试验条件.第5部分:工件夹紧盘定位的精度和可重复性

This part of ISO 10791 specifies, with reference to ISO 230-1 and ISO 230-2, the tests intended to assess the repeatability of positioning of individual pallets and the total accuracy of positioning of a batch of pallets associated with a specific machine. In a manufacturing system the accuracy of positioning of a workpiece or a work-holding fixture depends on the fitting between pallets and receivers. It should be noted that this part of ISO 10791 applies to a single machining centre, i.e. to the single receiver, with multiple pallets. The results of the tests considered here could be extended to the whole manufacturing system only if the measuring instruments were placed on the different machines exactly in the same position with respect to the origins of the linear axes. This, in practice, is difficult and inaccurate, because origins of the linear axis are affected by the repeatability of the axes.

Test conditions for machining centres - Accuracy and repeatability of positioning of work-holding pallets

ISO 10791-5:1998 加工中心检验条件 第5部分:工件夹持板的定位精度和重复定位精度

This part of ISO 10791 specifies, with reference to ISO 230-1 and ISO 230-2, the tests intended to assess the repeatability of positioning of individual pallets and the total accuracy of positioning of a batch of pallets associated with a specific machine. In a manufacturing system the accuracy of positioning of a workpiece or a work-holding fixture depends on the fitting between pallets and receivers. It should be noted that this part of ISO 10791 applies to a single machining centre, i.e. to the single receiver, with multiple pallets. The results of the tests considered here could be extended to the whole manufacturing system only if the measuring instruments were placed on the different machines exactly in the same position with respect to the origins of the linear axes. This, in practice, is difficult and inaccurate, because origins of the linear axis are affected by the repeatability of the axes.

Test conditions for machining centres - Part 5: Accuracy and repeatability of positioning of work-holding pallets

ISO 10791-7:1998 加工中心检验条件 第7部分:精加工试件精度

This part of ISO 10791 specifies, with reference to ISO 230-1, series of cutting tests, under finishing conditions, of standard test pieces, as well as the characteristics and dimensions of the test pieces themselves. This part of ISO 10791 is intended to supply minimum requirements for assessing the cutting accuracy of the machine. Different, more severe or more expensive tests may be performed by agreement between supplier/manufacturer and user.

Test conditions for machining centres - Part 7: Accuracy of a finished test piece

JB/T 7447.2-1994 机床通用部件 名义尺寸大于800mm的工件随行托板

The workpiece accompanying pallet with the nominal size of the common parts of the machine tool greater than 800mm

JB/T 7447.1-1994 机床通用部件 名义尺寸至800mm的工件随行托板

The workpiece accompanying pallet with the nominal size of the common parts of the machine tool up to 800mm

JB/T 7448.1-1994 小型组合机床 精度

本标准规定了小型组合机床的几何精度和工作精度的要求及检验方法。 本标准用于名义尺寸至250mm的主轴部件组成的回转工作台式、移动工作台式和固定工作台工式小型组合机床。如有特殊要求，可另提补充规定。

Accuracy of small combination machine tool