J78 真空技术与设备 标准查询与下载

NF X10-502-2:2012 真空技术 - 词汇 - 第2部分: 真空泵和相关术语.

Vacuum technology - Vocabulary - Part 2 : vacuum pumps and related terms.

NF X10-502-1:2012 真空技术 - 词汇 - 第1部分: 一般术语.

Vacuum technology - Vocabulary - Part 1 : general terms.

NF X10-510-1:2012 真空技术.测量真空泵性能的标准方法.第1部分:通用描述

Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 1 : general description.

NF X10-510-2:2012 真空技术.测量真空泵性能的标准方法.第2部分:蒸汽真空泵

Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 2 : positive displacement vacuum pumps.

ISO 14291:2012 真空计.四极质谱仪定义和规格

Vacuum gauges - Definitions and specifications for quadrupole mass spectrometers

BS ISO 21360-2:2012 真空技术.测量真空泵性能的标准方法.容积式真空泵

Vacuum technology. Standard methods for measuring vacuum-pump performance. Positive displacement vacuum pumps

BS ISO 21360-1:2012 真空技术.测量真空泵性能的标准方法.总则

Vacuum technology. Standard methods for measuring vacuum-pump performance. General description

JB/T 11282-2012 喷雾冷却制粒机

本标准规定了喷雾冷却制粒机的术语和定义、型号与标记、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于石蜡、硬脂酸、氨基脂肪酸固化物料的喷雾冷却制粒机（以下简称制粒机）。

Spray cooling granulator

JB/T 11281-2012 沸腾制粒机

本标准规定了用于粉体物料制粒的沸腾制粒机的术语和定义、型号与标记、技术要求、试验方法、检验规则、标志、使用说明书、包装、运输及贮存。 本标准适用于沸腾制粒机（以下简称制粒机）。

Fluidized granulator

JB/T 10176-2012 旋转闪蒸干燥机

本标准规定了用于粉状、颗粒状物料干燥的旋转闪蒸干燥机的术语和定义、型号与标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于旋转闪蒸干燥机（以下简称干燥机）。

Rotary flash dryer

JB/T 11283-2012 沸腾干燥机

本标准规定了用于颗粒状、粉状物料干燥的沸腾干燥机的术语和定义、分类与标记、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于沸腾干燥机（以下简称干燥机）。

Fluidized drying machine

ISO 21360-1:2012 真空技术.测量真空泵性能的标准方法.第1部分:一般描述

Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 1: General description

ISO 21360-2:2012 真空技术.测量真空泵性能的标准方法.第2部分:蒸汽真空泵

This part of ISO 21360 specifies methods for measuring the volume flow rate, base pressure, water vapour tolerance, power consumption, and the lowest start-up temperature of positive displacement vacuum pumps, which discharge gas against atmospheric pressure and with a usual base pressure

Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 2: Positive displacement vacuum pumps

BS ISO 3567:2012 真空计.通过直接与标准真空计的比较进行校准

Vacuum gauges. Calibration by direct comparison with a reference gauge

JB/T 8107-2011 容积真空泵 振动测量方法

本标准规定了容积真空泵的振动测量方法,三项振动量值振动速度、振动位移、振动加速度的标示方法,测量环境,测量仪器,测量时的安装、负载、工作条件和测点位置。本标准适用于在容积真空泵(以下简称泵)的非旋转或非往复式部件上进行的振动测量。本标准不适用于液环式真空泵。

Positive-displacement vacuum pump - Measuring methods for mechanical vibration

JB/T 11237-2011 真空技术 多级罗茨干式真空泵

本标准规定了多级罗茨干式真空泵基本参数、技术要求、测量方法与检验规则、标志、包装、运输和贮存。本标准适用于除单级、双级以外的多级罗茨干式真空泵。

Vacuum technology - Multi-stage Roots dry pumps

JB/T 7673-2011 真空技术 真空设备型号编制方法

本标准规定了真空泵、真空机组、真空阀门和真空镀膜机型号的编制方法。本标准适用于上述各种真空设备的型号编制。

Vacuum technology - Methods for compiling vacuum equipment models

JB/T 4081-2011 真空技术 溅射离子泵

本标准规定了普通型式的溅射离子泵(以下简称离子泵)的型式与基本参数、要求、测量方法、检验规则、标志、包装、运输、贮存及质量保证要求。本标准适用于普通型式的溅射离子泵。

Vacuum technology - Sputter ion pump

JB/T 11238-2011 真空技术 液环真空泵效率

本标准规定了单级液环(水或其他液体)真空泵入口压力为400 hPa时的等温压缩效率(以下简称为效率)曲线及应用方法。本标准适用于气量大于或等于1 m/min的单级液环真空泵(以下简称泵)。

Vacuum technology - Efficiency of liquid- ring vacuum pumps

ISO 3567:2011 真空计.同参考量规直接比较进行校准

This International Standard specifies the physical, technical and metrological conditions to be fulfilled when calibrations of vacuum gauges are performed by direct comparison with a reference gauge. From the conditions described, the design of an apparatus that can perform vacuum gauge calibrations in an adequate manner can be deduced. The vacuum gauges to be calibrated can be of any kind. Many types of gauges consist of several parts. Typically, these are: gauge head, cable, operational device and signal read out. This entire set is considered as the unit that has to be calibrated. Whereas, if only the gauge head (i.e. the part of the vacuum gauge directly exposed to the vacuum) is calibrated, all set-ups and conditions would have to be recorded such that the user of the calibrated gauge head would be able to perform the measurements in the same manner as during the calibration. The reference gauge is either a calibrated gauge, traceable to a vacuum primary or national standard (normal case), with a calibration certificate according to ISO/IEC 17025, or an absolute measuring instrument (rare case), traceable to the SI units and to which a measurement uncertainty can be attributed. This International Standard does not give guidance on how to treat special types of vacuum gauges, be they reference standards or units under calibration; it is intended that such guidance be given in other International Standards. The pressure range for calibrations treated in this International Standard depends on the realized design of the calibration apparatus and on the type of reference gauge. The range varies in its limits from 10 −6 Pa to 110 kPa. The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC Guide 98-3, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) ISO/IEC 17025:2005, General requirements for the competence of testing and calibration laboratories 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 primary standard measurement standard established using a primary reference measurement procedure ISOURCE: ISO/IEC Guide 99:2007, 5.4, modified] 3.2 national standard measurement standard recognized by national authority to serve in a state or economy as the basis for assigning quantity values to other measurement standards for the kind of quantity concerned ISOURCE: ISO/IEC Guide 99:2007, 5.3]  1

Vacuum gauges - Calibration by direct comparison with a reference gauge