K05 电工产品机械结构 标准查询与下载

BS 4662:2006+A1:2009 电气附件的埋入安装用盒子.要求,试验方法和尺寸规格

This British Standard specifies dimensional and other " requirements for boxes for flush mounting of electrical accessories in a wall, or other flat surfaced structure to ensure interoperability. The performance and safety requirements for products conforming to this standard are contained in BS EN 60670-1. This standard specifies requirements for boxes made from metal and for boxes made from non-metallic materials. This standard also specifies !dimensional and other requirements for mounting lugs necessary for mounting the electrical accessory in the box and the fixing holes necessary for fixing the box to the surface to which it is to be attached. This includes the position and numbers of accessory fixing lugs, requirements for M3.5 threaded fixing holes for the mounting of electrical accessories and provisions for lugs allowing angular adjustment of the accessory with threaded M3.5 holes for accessory fixing.

Boxes for flush mounting of electrical accessories - Requirements, test methods and dimensions

BS 4662:2006 电气附件嵌入装置用箱.要求、试验方法和尺寸

This British Standard specifies requirements for boxes for flush mounting of electrical accessories in a wall, or other flat surfaced structure to ensure interoperability. It is applicable to boxes for the mounting of electrical accessories with a rated voltage up to and including 440 V. This standard specifies requirements for boxes made from metal and for boxes made from non-metallic materials. This standard also specifies the mounting lugs necessary for mounting the electrical accessory in the box and the fixing holes necessary for fixing the box to the surface to which it is to be attached. This includes the position and numbers of accessory fixing lugs, requirements for M3.5 threaded fixing holes for the mounting of electrical accessories and provisions for lugs allowing angular adjustment of the accessory with threaded M3.5 holes for accessory fixing.

Boxes for flush mounting of electrical accessories - Requirements and test methods and dimensions

UL SUBJECT 2062-2006 危险(已分级)场所用外壳调查大纲.发布编号:2

1.1 These requirements cover enclosures classified with respect to explosion and fire hazard only. These enclosures are intended for installation and use in hazardous (classified) locations, Class I, Groups A, B, C, and D, and Class II, Groups E, F, and G, in accordance with the National Electrical Code, NFPA 70. 1.2 A product that contains features, characteristics, components, materials, or systems new or different from these in use when the Outline of Investigation was developed, and that involves a risk of fire, electric shock, or injury to persons, shall be evaluated using the appropriate additional component and end-product requirements as determined necessary to maintain the level of safety for the use of the product as originally anticipated by the intent of this Outline of Investigation.

Outline of Investigation for Enclosures for Use in Hazardous (Classified) Locations Issue Number 2

BS EN 60670-1:2005 家用和类似固定电气装置的电气附件用盒和外壳.一般要求

This part of IEC 60670 applies to boxes, enclosures and parts of enclosures (hereafter called “boxes” and “enclosures”) for electrical accessories with a rated voltage not exceeding 1 000 V a.c. and 1 500 V d.c. intended for household or similar fixed electrical installations, either indoors or outdoors. NOTE Requirements for particular types of boxes and enclosures are given in the relevant parts 2 of IEC 60670. Boxes and enclosures complying with this standard are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C. This International Standard is intended to apply to boxes and enclosures for electrical accessories within the scope of IEC technical committee 23. NOTE This standard may also be used as a reference document for other IEC technical committees and subcommittees. A box or an enclosure which is an integral part of an electrical accessory and provides protection for that accessory against external influences (for example mechanical impact, ingress of solid objects or water, etc.) is covered by the relevant standard for such an accessory. This standard does not apply to – ceiling roses; – luminaire supporting couplers; – boxes, enclosures and parts of enclosures specifically designed to be used for cable trunking and ducting systems complying with IEC 61084 and which are not intended to be installed outside of these systems.

Boxes and enclosures for electrical accessories for household and similar fixed electrical installations. General requirements

SANS 62262:2004 外壳法抵御电气设备受到的外来机械冲击时，其所能提供的防护程度(IK规范)

Refers to the classification of the degrees of protection provided by enclosures against external mechanical impacts when the rated voltage of the protected equipment is not greater than 72,5 kV. It will only apply to enclosures of equipment where the specific standard establishes degrees of protection of the enclosure against mechanical impacts (expressed in this standard as "impacts")

Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)

SANS 60670-22:2003 家用和类似固定电气装置的电气附件用机箱和外壳．第22部分：连接机箱和外壳的特殊要求

Applies to connecting boxes for junctions or tappings (or both), and enclosures and parts of enclosures for electrical accessories with a rated voltage not exceeding 1 000 V a.c. and 1 500 V d.c. intended for household or similar fixed electrical install

Boxes and enclosures for electrical accessories for household and similar fixed electrical installations Part 22: Particular requirements for connecting boxes and enclosures

UL SUBJECT 2441-2003 部件连接器外壳调查大纲.发布编号:1

1 Scope 1.1 These requirements cover single and multi-pole insulating housings without electrical contacts. They are intended for factory assembly to contacts (pins) by the end use manufacturer and are evaluated using the material construction requirements of the end use product. 1.2 This outline supplements the following: a) Connector housings for assembly onto flexible cord or cable that are covered by the Standard for Cord Sets and Power-Supply Cords, UL 817; b) Connector housings for use with attachment plugs, cord connectors, receptacles, inlets, and outlets, that are covered by the Standard for Attachment Plugs and Receptacles, UL 498; c) Connector housings for use with wire connectors and soldering lugs that are covered by the Standards for Wire Connectors - For Use With Copper Conductors, UL 486A; Splicing Wire Connectors, UL 486C; or Equipment Wiring Terminals, UL 486E; d) Connector housings for use with quick-connect terminals that are covered by the Standard for Quick Connect Terminals, UL 310. e) Connector housings for use with component connectors that are covered by the Standard for Component Connectors for Use in Data, Signal, Control and Power Applications, UL 1977.

OUTLINE OF INVESTIGATION FOR COMPONENT - CONNECTOR HOUSINGS Issue Number 1

JB/T 10382-2002 电气设备机械门锁通用技术条件

本标准规定了电气设备机械门锁产品的型号、技术要求、检测方法、检验规则、抽样和标志、包装与贮存。 　　本标准适用于电气设备机械门锁产品的设计、制造、检验与验收。

General technical specification for mechanical door lock of electronic equipment

JB/T 10324-2002 电气设备机柜通用技术条件

本标准规定了电气设备机柜的技术要求、检验方法、检验规则及标志、包装、运输和贮存。 　　本标准适用于型材或金属板材制造的机柜。

General technical specification for cabinets of electronic equipment

UL 50E BULLETINS-2001 (草案)(草案)电气设备用外壳环境UL安全标准

Covers electrical equipment enclosures for use in accordance with the National Electrical Code, NFPA 70. Specific applications covered by this standard include cabinets and cutout boxes and junction and pull boxes. Each type of enclosure covered by this standard is described in general and functional terms where practicable, and omits reference to structural details and specific applications except where they are essential to the identification of the enclosure type. Such additional details and specifications are included in applicable standards for the end-product involved.

(Draft)(DRAFT) UL Standard for Safety for Enclosures for Electrical Equipment, Environmental Considerations

CSA C50052-99-CAN/CSA-1999(R2007) 外壳在 aZZ3a.ed鎶媄unzinium couZ5 用于 Z鎶瞤paueeiZZuge 高压下的气压 Premiere Edition;文件编号 1：4/1999

EnveZoppes en aZZ3a.e d抋Zunzinium couZ5 pour Z抲ppaueeiZZuge a haute tension sous pression de gaz Premiere Edition; Fiche no 1: 4/1999

CSA C50069-99-CAN/CSA-1999(R2007) 充气高压开关和控制设备用锻铝和铸铝合金焊接复合外壳

Enveloppes en acier soud?pour l抋ppareillage a haute tension sous pression de gaz Premiere edition; Incorporates Fiche No 1: 4/1999

CSA C50064-99-CAN/CSA-1999(R2007) 用于高压气体压力 pauizing 的 aZuminium 和铝 aZZiZZizing cowoyi5s 外壳 第一版：合并 第 1 号表：4/1999

EnveZoppes en aZuminium et aZZiage d抋luminium cowoyi5s pour Z抋ppaueiZZage a haute tension sous pression de gaz Premiere edition: Incorporates Fiche no 1: 4/1999

BS EN 60917-1:1999 电子设备机械结构研制用模数序列.通用标准

This International Standard relates to equipment practices. The modular order is applicable to the main structural dimensions of electronic equipment mounted in various installations where dimensional interfaces have to be considered. It refers to basic design parameters and is not intended to be used for manufacturing tolerances or clearances. In addition, information on interfaces to other technical fields, on technology and advanced design aspects is included. This standard also covers standard terms for parts and assemblies of mechanical structures for electronic equipment. This generic standard gives the definitions of a modular order for mechanical structures of electronic equipment and provides for dimensional compatibility at mechanical interfaces with related engineering applications, e.g. printed boards, components, instrumentation, furniture, rooms, buildings, etc. Furthermore, it supports the introduction and application of the modular order rules considering that: - compatibility of interface dimensions is aimed at the electronic field on the basis of the SI unit metre; - technical and economic advantages can be achieved when using the rules. The terms in this standard should be used in all standards for mechanical structures of electronic equipment and in related technical documents.

Modular order for the development of mechanical structures for electronic equipment practices - Generic standard

CSA C50068-99-CAN/CSA-1999(R2007) 气压下高压开关设备的焊接钢外壳第一版；合并文件编号 1：4/1999

Enveloppes en acier soud?pour l抋ppareillage a haute tension sous pression de gaz Premiere edition; Incorporates Fiche no 1: 4/1999

KS C 6458-1997 多层印刷线路板用预浸料坯(玻璃布基、环氧化物树脂)

이 규격은 다층 프린트 배선판에 사용하는 유리천 바탕재 에폭시 수지 프리프레그에 대하여 규

Prepreg for multilayer printed wiring boards (Epoxy resin-Impregnated glass cloth)

JB/T 6753.2-1993 电工设备的设备构件公差.金属剪切件一般公差

本标准规定了料厚至12mm的金属板材剪切件的一般公差。 本标准适用于电工设备的设备构体中用剪板机剪切下料和直接获得的剪切件。对用其它方法加工的板材、带材、条料及型材的剪切下料和加工件也可参照使用。

Tolerance of component parts of electrical equipments General tolerance of metal shear parts

JB/T 6753.3-1993 电工设备的设备构件公差.金属冷冲压件一般公差

本标准规定了料厚至12mm的金属冷冲压件的一般公差。 本标准适用于电工设备的设备构件中冷冲压件的一般公差。对于其它加工方法加工的钣金件和非金属板的孔加工件也可参照使用。

Tolerance of component parts of electrical equipments General tolerance of metal cold stamping parts

JB/T 6753.4-1993 电工设备的设备构件公差.焊接结构一般公差

本标准规定了焊结构的一般公差。 本标准适用于电工设备的焊接结构的设备构体的加工。

Tolerance of component parts of electrical equipments General tolerance of welded structures

JB/T 6753.5-1993 电工设备的设备构件公差.组装结构一般公差

本标准规定了组装结构的一般公差。 本标准适用于电工设备的组装结构，以及各组装结构单元的设备构体的加工。

Tolerance of component parts of electrical equipments General tolerance of assembled structures